• 한국환경과학회지
• /
• 제27권2호
• /
• pp.99-107
• /
• 2018

In order to design the improvement process for T-N removal, the treatment process of Suyoung, Gangbyeon, and Noxan sewage treatment plants (STP) in Busan was anlayzed. Suyoung STP shows a T-N removal efficiency of about 69.8% with MLE(Modified Ludzack ettinger) and A2O+MBR. However, it is necessary to improve the process to maintain over DO of 1 mg/L and is required to install a flow control tank to minimize the rainfall effect. Gangbyun STP shows a about 70.2% T-N removal efficiency with A2O+GFF(gravity fiber filtration). However, in order to improve T-N removal efficiency, it is needed to install MLE process to treat recycle water. Noksan STP shows a T-N removal efficiency of about 71.0% with MLE+Chemical treatment and shows stable T-N concentration in effluent. However, it is required a toxic chemical management process because bad wastewater flows into the STP, also is necessary a process improvement in order to increase internal recycling ratio. Especially, it is required a process improvement to increase HRT of nitrification tank because Suyoung and Gangbyeon STPs shows low nitrification efficiency during winter season.

• 대한기계학회논문집B
• /
• 제23권5호
• /
• pp.670-677
• /
• 1999

An analysis of generation and growth of multicomponent particles has been carried out to predict the size and composition distributions of particles generated in the Modified Chemical Vapor Deposition(MCVD) process. In MCVD process. scale-up of sintering and micro-control of refractive index may need the Information about the size and composition distributions of $SiO_2-GeO_2$ particles that are generated and deposited. The present work solved coupled steady equations (axi-symmetric two dimensions) for mass conservation, momentum balance. energy and species(such as $SiCl_4$, $GeCl_4$, $O_2$, $Cl_2$) conservations describing fluid flow. heat and mass transfer in a tube. Sectional method has been applied to obtain multi-modal distributions of multicomponent aerosols which vary in both radial and axial directions. Chemical reactions of $SiCl_4$ and $GeCl_4$ were included and the effects of variable properties have also been considered.

• 공업화학
• /
• 제30권3호
• /
• pp.261-279
• /
• 2019

The aim of this review article is to summarize the role of titanium oxide ($TiO_2$) nanomaterials in the remediation of the aquatic environment contaminated with various emerging pollutants. The advanced oxidation process led by the semiconductor $TiO_2$ is an impetus in the remediation technology. Therefore, a vast number of literature works are available in this area. Further, the role of modified $TiO_2$ or thin film materials were discussed in the review. Also, the Localized Surface Plasmon Resonance (LSPR) effect of using noble metaldoped $TiO_2$ played an interesting role in the remediation process.

• 공업화학
• /
• 제5권6호
• /
• pp.1016-1023
• /
• 1994

Acrylonitrile 제조시 부산물로 생성되는 acetonitrile-water 공비혼합물에서 용매추출하여 acetonitrile을 회수하기 위하여 benzene, toluene, o-xylene, ethylacetate 및 monochlorobenzene을 용매로 선택하여 $25^{\circ}C$ 에서 solvent(1)-water(2)-acetonitrile(3)계의 액-액 평형데이타를 구하였으며, 그 실험데이타의 건전성을 조사하였고, tie line과 plait point조성을 결정하였다. 또한 NRTL, UNIQUAC 및 modified UNIQUAC모델식에 적용하여 parameter를 추산하고 각 용매에 대한 분배계수와 선택도를 결정하였다.

• Bulletin of the Korean Chemical Society
• /
• 제25권2호
• /
• pp.182-184
• /
• 2004

Fine $La_{2/3}Ca_{1/3}MnO_3$ nanocrystalline powders have been successfully prepared by modified citrate pyrolysis process. The obtained LCMO nanoscale grains have a mean particle size of about 30 nm under optimal treatment conditions. The particle size can be controlled by adjusting processing parameters, such as treatment temperature and calcination time. X-ray diffraction, SEM and magnetoresistance effect were employed to study the crystal structure, morphology and magnetic property of these nanosized powders. A novel MR effect (MR > 45% (0 K < T < 340 K)) at room temperature has been found.

• 한국재료학회지
• /
• 제31권12호
• /
• pp.657-664
• /
• 2021

To build a highly active photocatalytic system with high efficiency and low cast of TiO₂, we report a facile hydrothermal technique to synthesize Ag₂Se-nanoparticle-modified TiO₂ composites. The physical characteristics of these samples are analyzed by X-ray diffraction, scanning electron microscopy with energy dispersive X-ray analysis, transmission electron microscopy and BET analysis. The XRD and TEM results show us that TiO₂ is coupled with small sized Ag₂Se nanoplate, which has an average grain size of about 30 nm in diameter. The agglomeration of Ag₂Se nanoparticles is improved by the hydrothermal process, with dispersion improvement of the Ag₂Se@TiO₂ nanocomposite. Texbrite BA-L is selected as a simulated dye to study the photodegradation behavior of as-prepared samples under visible light radiation. A significant enhancement of about two times the photodegradation rate is observed for the Ag₂Se@TiO₂ nanocomposite compared with the control sample P25 and as-prepared TiO₂. Long-term stability of Ag₂Se@TiO₂ is observed via ten iterations of recycling experiments under visible light irradiation.

• 한국물환경학회지
• /
• 제23권3호
• /
• pp.309-313
• /
• 2007

In Activated Sludge Model, COD fraction of primary settled municipal wastewater was a very important parameter. In this study, the COD fraction was determined using the oxygen utilization rate experiments. Readily biodegradable COD ($S_S$) fraction was observed about 29.7% of influent TCOD. $S_I$, $X_I$, and $X_S$ were analyzed to be 7.6%, 7.3%, and 55.4% of TCOD, respectively. The model used in this study was developed based on ASM3 and modified Bio-P module in order to simulate the existing BNR process. Parameter estimation results showed that $Y_{STO,O2}$, $Y_{STO,NO}$, $Y_{H,O2}$, $Y_{H,NO}$, $Y_{PO4}$, ${\mu}_H$, $b_H$, ${\mu}_A$, $q_{PHA}$, $q_{PP}$ and ${\mu}_{PAO}$ were 0.7, 0.64, 0.61, 0.48, 0.31, 3.9, 0.1, 1.35, 4.98, 1.8 and 0.59, respectively. Using the presented model and the estimated parameters, the simulation of the existing BNR process was successfully conducted.

• 접착 및 계면
• /
• 제7권4호
• /
• pp.32-38
• /
• 2006

A series of organic-inorganic hybrids, PCL/EP/$SiO_2$, involving epoxy resin and triethoxysilane-terminated polycaprolactone elastomer (PCL-TESi) were prepared via polymerization of diglycidyl ether of bisphenol A (DGEBA) with amine curing agent KB-2 and sol-gel process of PCL-TESi. The curing reactions were started from the initially homogeneous mixture of DGEBA, KB-2 and the PCL-TESi. The organicinorganic hybrids containing up to 4.95% (wt) of $SiO_2$ were obtained and characterized by FT-IR, transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). It was experimentally shown that the swelling property in toluene, morphologies and thermal properties of the resulting hybrids were quite dependent on the contents of $SiO_2$. The crosslink network density decreases with increasing of the PCL-TESi. And in TEM, the phase separated morphology of these hybrids was found, which resulted from the coagulation of Si-O-Si networks resulting from $-Si(OC_2H_5)_3$ of PCL-TESi self-curing by hydrolytic silanol condensation, with the advancement of the curing reaction in the modified epoxy resin systems. Meanwhile, the change of the $SiO_2$ content made the morphologies changed from aggregated particles of Si-O-Si in the hybrid to nanocluster of interconnected Si-O-Si particles, then to aggregated Si-O-Si dispersing in the continuous cured epoxy phase again, and last to co-continuous interpenetrating network. The glass transition behavior of the hybrid material was cooperative motion of large chain segments, which were hindered by the inorganic Si-O-Si network. And in TG analysis, the characteristic temperature at 5% of weight loss was evidently increased from $120.5^{\circ}C$ of pure cured epoxy to $277.6^{\circ}C$ of 3.84% (wt) of $SiO_2$ modified epoxy due to the existence of Si-O-Si when PCL-TESi was added in the hybrid.

• 한국분말재료학회지
• /
• 제8권3호
• /
• pp.201-206
• /
• 2001

$>LaMnO_3$$(La, Sr)MO_3$, and $(La, Sr)MO_3/YSZ$ gel films were deposited by spin-coating technique on scandium-doped zirconia (YSZ) substrate using the precursor solution prepared from $La(O-i-C_3H_7)_3$, $Co(CH_3COO)_2$or $Mn(O-i-C_3H_7)_2$,2-methoxyethanol, and polyethylene glycol. By heat-treating the gel films, the electrochemical cells, $(La, Sr)MnO_3{\mid}ScSZ{\mid}Pt$ were fabricated. The effect of polyethylene glycol on the microstructure evolution of $$LaCoO_3and $LaMnO_3$thin films was investigated, and NOx decomposition characteristics of the electrochemical cells were investigated at $500^{\circ}C$ to $600^{\circ}C$. By applying a direct current to the $(La, Sr)MnO_3{\mid}ScSZ{\mid}Pt$ electrochemical cell, good NOx conversion rate could be obtained relatively at low current value even if excess oxygen is included in the reaction gas mixture.

• 한국가스학회지
• /
• 제8권1호
• /
• pp.37-47
• /
• 2004

탄소분자체(CMS)를 사용하여 산소를 정제하기 위한 압력순환식 흡착 공정(PSA)을 연구하였다. 본 연구에서는 zeolite를 사용하는 일반적인 평형 분리 PSA 공정의 생산제품으로 가정된 2성분 혼합가스 ($O_2$/Ar- 95:5 vol.$\%$)와 두 개의 서로 다른 3성분 혼합가스를 ($O_2/Ar/N_2$- 95:4:1, 90:4:6 vol.$\%$) 공급기체로서 사용하였고, $99\%$ 이상의 고순도를 얻기 위한 공정이 개발되었다. 두번의 연속 감압 단계를 포함하는 개발공정의 결과로서 산소 $93\%$를 포함한 공급류의 경우 약 $99.8\%$의 고순도와 함께 $56\%$정도의 회수율을 얻을 수 있었으며, 산소 $90\%$를 포함한 공급류에 대하여도 $97\%$이상의 고순도 산소를 생산해 낼 수 있었다. 본 연구에서 개발된 공정의 경우 흡착제에 대한 흡탈착속도 차이를 이용하여 분리 정제가 진행되며, 공정을 정확히 모사하기 위하여 Langmuir isotherm이 결합된 modified structural diffusion model을 적용하였다.