• Journal of Welding and Joining
• /
• v.2 no.2
• /
• pp.62-69
• /
• 1984

In this study, cold crack susceptibility of high strength steel (ABS EH32 Steel) welded zone with shielded metal are welding was investigated by tensile restraint cracking test method. Effects of diffusible hydrogen content on root cracking, lower critical stress, crack initiation and fracture mode, hardness value distribution of welded zone and fractograph were mainly investigated. Following conclusions are made: 1. In the view of the lower critical stress level, wet electrode, containing much diffusible hydrogen content shows lower value than dried electrode. 2. Hardness value(Hv 5kg) in Heat Affected Zone of wet electrode is higher than that of dried electrode caused by hydrogen embrittlement. 3. In the case of wet electrode, root crack is initiated and propagated in Heat Affected Zone and then propagated to weld metal, but using of dried electrode, root crack is initiated in Heat Affected Zone and propagated to weld metal without propagating in HAZ. 4. For wet electrode, quasi-cleavage fracture mode is majorly observed on the fracture surface of HAZ and partially of weld metal due to hydrogen embrittlement.

• Journal of Korean Society on Water Environment
• /
• v.27 no.3
• /
• pp.357-363
• /
• 2011

In spite of numerous advantages in railroads such as mass transportation, high reliability, and environmental soundness etc., the value of railroad construction is relatively underestimated compared to road. This is because the current method of evaluation focuses mainly on economic effect. In this study, considering recent research results, the environmental value of railroad construction was assessed by calculating the effect of reduction of emissions and water contamination. With these two benefits, the environmental effect produced by railroads and road construction was calculated and compared to each other using EMME/3. As a result, the senario 4 which considers 'Hot/Cold start' condition and water contamination had highest benefits. Furthermore, the environmental effect produced by railroad is 55~101% higher than road construction. If the suggested method is used in the current appraisal system, the environment-friendly mode like railway would be highly valued, much more than before.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.288-298
• /
• 2017

The system of high-speed and conventional railway vehicles is diversified, and significant technological development in performance has been achieved. This study analyzed the modal change characteristics; furthermore, it estimated the value of travel time by improving the travel time and cost for the passenger's perception of railway. In this study, we formulate a mode choice model for passengers and compare it with the mixed logit model which reflects individual taste variation. In addition, the validity of the analysis is presented through an estimation the value of travel time using the derived model. For this purpose, a stated preference survey was conducted with 510 people using public transportation. The benefits of time-saving can be accurately determined by estimating the value of time spent on the railway. Appropriate fares for public transportation can also be estimated.

• Journal of ILASS-Korea
• /
• v.18 no.3
• /
• pp.132-139
• /
• 2013

Smoke emissions from light duty diesel vehicles were measured using light extinction method with the free acceleration test mode. The smoke emissions for each measurement cycle of the free acceleration method showed large variations according to driver's pedal pushing pattern. The smoke values for each measurement cycle initially increased and reach a peak value. Integration of the smoke emissions with time for each measurement cycle was performed to get a representative smoke value which was obtained by averaging the integrated results. Two kinds of integration time range were used. One is range over the whole measurement cycle of the free acceleration method. The other is only the acceleration range in the measurement cycle. Overall, variation of the representative smoke values obtained by the integration method was reduced comparing to the traditional representative smoke value which was obtained from a peak smoke value over the measurement cycle. Ten vehicles of the same model with 2.5 liter diesel engines, and seven vehicles of the same model with 2.7 liter diesel engines, were tested using the free acceleration test method.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.276.2-278
• /
• 2000

In a recent years, a number of approaches have been studied, including passive, active, and hybrid mode-locking of semi-conductor lasers for short pulse generation and research has been devoted to achieve low timing-jitter operation since the timing jitter is unfavorable for system applications. Among the methods of mode locking, passive mode locking does not need external rf drives, and therefore the operation and fabrication procedures are simplified. In spite of these attractive advantages of passive mode-locked laser, it has critical drawbacks such as large timing jitter and the difficulty in synchronization with external circuits. Their inherent large timing jitter value was shown to be suppressed to certain levels by means of hybrid mode-locking technique$^{(1)}$ , where the saturable absorber section was modulated by an external signal with the cavity round trip frequency. Furthermore, the subharmonic mode-locking (SHML) technique alleviates the restrictions of high speed driving electronics. It has been demonstrated experimentally$^{(1)}$ that the hybrid subharmonic mode-locking technique has lead to significant reduction of the timing jitter. (omitted)

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.90-96
• /
• 2011

In this study, the characteristic of fractured portion and shape on solder joints were investigated according to the thermal shock test for Automotive Application Component using Sn-3.0Ag-0.5Cu solder, which has a outstanding property as Lead-free solder. The value of pull and shear strength was decreased in principle after 432 cycles thermal shock test. In addition, fracture mode was verified by using EDS and SEM to observe fractured shape on the solder joints before and after thermal shock. In before thermal shock test, the fracture mode revealed typically solder layer's fracture mode. In after thermal shock test, we identified multiple fracture mode of the ductile and brittle fracture. Even though same composition of solder was used to experimental for estimating. the fracture mode varied on the fracture portion's height and the directional angles of shear strength. In conclusion, we identified that mechanical strength was affected on the solder layer's fracture mode.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.4
• /
• pp.379-384
• /
• 1999

In this paper, we present a new time-varying sliding surface to achieve fast and robust tracking of higher-order uncertain systems. The surface passes through an initial error, and afterwards, it moves towards a predetermined target surface by means of a variable named by sliding surface gain and its intercept. Specifically, the sliding surface gain is determined so that its initial value can minimize a shifting distance of the surface and that the system roots in sliding mode can follow certain stable trajectories. The designed sliding mode control forces the system errors to stay always on the proposed surface from the beginning. By this means, the system remains insensitive to system uncertainties and disturbances for the whole time. To illustrate the effectiveness of the proposed method, the comparative study with conventional time-invariant sliding mode control is performed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.99-110
• /
• 1995

An industrial robot needs a simple and robust control algorithm obtaining high precision control performance in spite of disturbance and parameter's change. In this paper, for solving this problem, a new sliding mode control algorithm is proposed and applied to the trajectory control of a SCARA type robot. The proposed algorithm has diminished the chattering occurring in sliding mode by setting a dead band along the switching line on the phase plane. It shows that we can easily obtain a simple switching control input satisfying sliding mode in spite of regarding nonlinear terms of a manipulator and servo system as disturbance. A guideline for selection of dead-band width is determined by optimal value of cost function presenting magnitudes of chattering and error. By this algorithm, we can expect the high performance of the trajectory tracking of an industrial robot which needs a robust and simple algorithm.

• Knowledge Management Research
• /
• v.17 no.4
• /
• pp.163-189
• /
• 2016

The importance of Information technology (IT) has been growing. Thus, it is critical for firms to choose the optimal information technology development mode in order to ensure that maximum benefit is derived from IT. Despite its importance, however, there is little comprehensive research on choosing the IT development mode that firms undertake. To fill this gap, this study attempts to propose a parsimonious as well as comprehensive IT development framework based on strategic value and the uniqueness of IT resources. In addition, this study analyzes the impact of the fit between the theoretically proposed IT development mode and the actually used mode on the performance of Korean firms. This study contributes to and expands the literature on IT development modes by considering various development modes in real time. Moreover, the results serve as a stepping stone for managers who want to develop or adopt IT effectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.49-50
• /
• 2006

We have developed vertical alignment liquid crystal display (VA-LCD), of which the viewing angle can be controlled. The VA-LCD has the function of switching between the wide viewing mode and narrow viewing angle mode using one homogeneous aligned (HA) LC layer and one compensation film with a negative C-plate. The retardation of the HA layer at off axis can be controlled by applying an electric field while keeping the retardation value to be zero at normal direction. Consequently, the device exhibits a viewing mode over $170^{\circ}$ in terms of CR = 10 in wide viewing mode and about $60^{\circ}$ in terms of CR = 2 in narrow viewing angle mode m horizontal direction.