• Journal of the Korean Society of Safety
• /
• v.24 no.5
• /
• pp.28-33
• /
• 2009

The thermochemical parameters for safe handling, storage, transport, operation and process design of flammable substances are explosion limit, flash point, autoignition temperatures(AITs), minimum oxygen concentration(MOC), heat of combustion etc.. Also it is necessary to know explosion limit at high temperature and pressure. For the safe handling of benzene, lower explosion limit(LEL) at $25^{\circ}C$, the temperature dependence of the explosion limits and flash point were investigated. And the AITs for benzene were experimented. By using the literatures data, the lower and upper explosion limits of benzene recommended 1.3 vol% and 8.0 vol%, respectively. This study measured relationship between the AITs and the ignition delay times by using ASTM E659-78 apparatus for benzene, and the experimental AIT of benzene was $583^{\circ}C$. The new equations for predicting the temperature dependence of the explosion limits of benzene is proposed. The values calculated by the proposed equations were a good agreement with the literature data.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.497-501
• /
• 2000

One of the way to derive design parameters of the fuel feeding system in satellite is to analyze unsteady flow of liquid propellant (hydrazine) in the propulsion system. During steady thruster firing the flow rate is constant: if a thruster valve is abruptly shut down among a sets of thrusters, pressure spikes much higher than the initial tank pressure occur. This renders the fuel flow unsteady, and the fluid pressure and flow rate to oscillate. If the pressure spikes are high enough, there are possibilities that propellant explosively decomposes, thruster valves are damaged, and adiabatic detonation of the hydrazine propellant is potentially incurred. Reflected shockwaves could also affect the calibration and operation of the pressure transducers. These necessitate the analysis of unsteady flow in the propulsion system design, and the calculation results obtained through some governing parameter variation are presented in this work.

• Nuclear Engineering and Technology
• /
• v.29 no.4
• /
• pp.320-326
• /
• 1997

The nuclide transport in the one-dimensional porous medium is considered as a first step in developing a decay chain transport in multidimensional inhomogeneous media. A method of solving conventional advection-dispersion equation with decay chain of arbitrary length by using the method of characteristics (MOC) is introduced. In specific cases where the advection are dominant rather than dispersion, the method is known to be useful : one of the most distinctive advantages in applying the model is that the MU minimizes the numerical dispersion, which is distinguished in such common numerical schemes as finite element method and finite difference method. The suggested model is considered to be effective through several illustrations for the case that decay chain of arbitrary length is involved during transport which is difficult to solve by standard numerical solutions if the medium becomes more complicated.

• Nuclear Engineering and Technology
• /
• v.44 no.2
• /
• pp.113-150
• /
• 2012

The point we made in this paper is that, although detailed and precise three-dimensional (3D) whole-core transport calculations may be obtained in the future with massively parallel computers, they would have an application to only some of the problems of the nuclear industry, more precisely those regarding multiphysics or for methodology validation or nuclear safety calculations. On the other hand, typical design reactor cycle calculations comprising many one-point core calculations can have very strict constraints in computing time and will not directly benefit from the advances in computations in large scale computers. Consequently, in this paper we review some of the deterministic 3D transport methods which in the very near future may have potential for industrial applications and, even with low-order approximations such as a low resolution in energy, might represent an advantage as compared with present industrial methodology, for which one of the main approximations is due to power reconstruction. These methods comprise the response-matrix method and methods based on the two-dimensional (2D) method of characteristics, such as the fusion method.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.287-291
• /
• 1999

This study was performed to develop an information processing system for the sound conservation of soil and groundwater resources. The system contains the geographic spatial information system(GSIS), and the numerical model of groundwater flow and contamination. Numerical models (MODFLOW, MOC3D, MT3D, PMPATH, PEST, UCODE) and GSIS(ArcView) were integrated for the construction of an integrated management system of subsurface environment. The developed system was applied to the management of three mineral water companies located in clean mountain area. The impact of pumping over the overall catchment basin was modeled using the developed system for the decision of future management criteria.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.775-780
• /
• 2003

In this study, a computer analysis has been developed for predicting the pipe pressure of the intake and exhaust manifold in a single cylinder engine. To get the boundary conditions for a numerical analysis, one dimensional and unsteady gas dynamic calculation is performed by using the MOC(Method Of Characteristic). The main numerical parameters are the variation of the exhaust pipe diameters to calculate the pulsating flow when the intake and exhaust valves are working. As the results of numerical analysis, the shapes and distributions of the exhaust pipe pressures were influenced strongly on the cylinder pressure. As the exhaust pipe diameter is decreased, the amplitude of exhaust pressure is large and the cylinder pressure was showed low in the region of intake valve opening time.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.1
• /
• pp.27-35
• /
• 2012

A numerical simulation for particle collection efficiency in a wire-plate electrostatic precipitator (ESP) has been performed. Method of characteristics and finite differencing method (MOC-FDM) were employed to obtain electric field and space charge density, and lattice boltzmann method (LBM) was used to predict the Electrohydrodynamic (EHD) flow according to the ion convection. Large eddy simulation (LES) was considered for turbulent flow and particle simulation was performed by discrete element method (DEM) which considered field charging, electric force, drag force and wall-collision. One way coupling from FDM to LBM was used with small and low density particle assumption. When the charged particle collided with the collecting plate, particle-wall collision was calculated for re-entertainment effect and the effect of gravity force was considered.

• Journal of Power System Engineering
• /
• v.8 no.1
• /
• pp.24-29
• /
• 2004

In this study, a computer analysis has been developed for predicting the pipe pressure of the intake and exhaust manifold. To obtain the boundary conditions for a numerical analysis, one dimensional and non-steady gas dynamic calculation is performed by using the MOC(Method Of Characteristic). The main numerical parameters are the variation of the engine revolution to calculate the pulsating flow which the intake and exhaust valves arc working. The comparison of exhaust pressure in case of numerical results is quite matched with in case of experimental results. When engine revaluation is increased, the pressure amplitude showed a high value, but the pressure frequency was decreased.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.14 no.1
• /
• pp.34-40
• /
• 2014

Today, with the wide use of mobile devices, the amount of business transactions conducted through such devices is increasing drastically. However, there are several limitations in the area of authentication for mobile use, which requires strong authentication mechanisms to satisfy security and convenience requirements. The proposed model and application system provide a framework to ensure the security and reliability of the flow of biometric information for telebiometric applications using mobile devices. We also specify protocols for each model and implement a mobile telebiometric application to improve security vulnerabilities compared to storage in a microSD match on card (MOC) based on the proposed model. As a consequence of this implementation, we propose substantial guidelines for security countermeasures from both technical and managerial perspectives in order to establish a safe mobile environment for the use of telebiometric systems.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.11 no.2
• /
• pp.79-92
• /
• 2003

This study is to identify the hazard of ozone and to evaluate ozone effect that is flowed into the cabin when the airplane is flying at high altitude. For this purpose, it is studied that how ozone is generated in the air, what the effect on human body is due to the cabin ozone and what the design criteria is considering or preventing the ozone hazard. And, finally the regulations and means of compliance are studied and introduced to assure that the aircraft satisfies the design criteria related to ozone.