• 한국버섯학회지
• /
• 제3권4호
• /
• pp.140-144
• /
• 2005

여름철 팽이버섯 병재배시 톱밥배지에서 발생하는 균사생장 억제증상의 원인을 구명하고 그 경감대책을 확립하기 위하여 톱밥배지 배합시 물온도를 $24^{\circ}C$(상온수)와 $6^{\circ}C$(저온수)로 하고, 배지제조후 살균전 경과시간을 0, 3, 6, 9시간으로 달리하여 팽이버섯의 재배시험을 수행하였다. 배지제조 후 살균전 시간이 경과함에 따라 배지온도가 상승하고, pH는 6.5에서 5.2~5.6으로 낮아지는 경향이었다. 이때 톱밥배지 내에서 세균밀도가 증가하였으며, 물온도 $24^{\circ}C$에서는 $6^{\circ}C$보다 6시간 이후의 세균밀도가 1.9~4.1배 높았다. 톱밥배지에서 분리한 세균과 대치배양시 팽이버섯균의 생장이 억제되었다. 또한 배지제조후 살균전 시간이 경과함에 따라 배지내의 전질소 함량이 감소하였으며 유리당의 함량도 종류에 따라서 증가 또는 감소하였다. 배지배합시 $24^{\circ}C$물 처리구는 $6^{\circ}C$물 처리구에 비하여 팽이버섯 병재배사에서 균배양기간 및 버섯발생기간이 각각 1~2일 지연되는 경향이었으며, 자실체 수량도 저온수 처리구에서 안정적이었다. 그리고 9시간 경과한 배지에서는 균사생장이 정지되었다. 배지제조후 경과시간에 따라 팽이버섯 발생기간은 1~3일이 지연이 되었으며, 자실체 수량은 6시간이 경과된 배지에서 7~12% 감소하는 경향이었다. 본 시험은 여름철 고온기의 팽이버섯 재배시 배지제조에 $6^{\circ}C$이하의 저온수를 사용하여 배지내 미생물 증식을 억제시키고, 입병작업을 마치는 즉시 고압살균 함으로써 배지의 성분을 안정화시켜 버섯의 안정생산에 기여할 것으로 기대된다.

• 상하수도학회지
• /
• 제21권3호
• /
• pp.359-366
• /
• 2007

Slow sand filtrations have been widely used for water treatment in small communities, however their capacity is often limited by high turbidity in the raw water. For this reason, several pre-treatment facilities were required for a slow sand filter. Turbidity removal from the highly turbid raw water was investigated in roughing filters as a pre-treatment process. The roughing filters followed by rapid mixing tank were operated in the form of a contact filtration. In several jar tests, the predetermined optimum aluminium sulfate (alum) doses for turbid water of 30 and 120NTU were 30 and 50mg/L, respectively. At the optimum alum dose, physically optimum parameters including G value of $220sec^{-1}$ and rapid mixing time of 3 minutes were applied to the contact filtration system. Without addition of alum, the filtrate turbidity from the roughing filters, packed respectively with different media such as sand, porous diatomite ball and gravel, was in the range of 5~30NTU at filtration velocities of 30 and 50m/day. However, the application of a contact filtration to roughing filters showed stably lower filtrate turbidity below 1.0NTU at filtration velocity of 30 m/day. Although the filtration velocity increased to 50m/day, filtrate turbidity was still below 1.0NTU in both single and double layer roughing filters. At influent turbidity of 120NTU, the filtrate turbidity was over 5 NTU in the triple layer roughing filter, which shortened the filter run time. The flocs larger than $10{\mu}m$, formed in the rapid mixing tank, were almost captured through the roughing filter bed, while the almost flocs smaller than $10{\mu}m$ remained in filtrate.

• 한국해양학회지:바다
• /
• 제18권3호
• /
• pp.111-121
• /
• 2013

지역규모의 정확한 일기예보와 해양생태계 변화 이해에 있어서 수온 예측은 매우 중요하다. 황해는 조류가 매우 빠르고 탁도가 높다. 이러한 해역에서는 수치 모델의 수직 혼합 기법 및 해수의 탁도에 따른 수형(water type)이 수온 구조 결정에 많은 영향을 미친다. 수직 혼합 기법 변화와 탁도의 변화에 따른 황해 수온 모사의 민감도를 알아보기 위해 3차원 해양 순환 모델인 Regional Ocean Modeling System (ROMS)을 사용하여 수치 실험을 수행하였다. 수직 혼합 기법은 해양 순환 모델에서 많이 사용되는 Mellor-Yamada level 2.5 closure(M-Y)와 K-Profile parameterization (KPP)을 사용하고, 탁도는 Jerlov의 분류에 따른 수형 1, 3, 5를 사용하여 수치 실험을 수행하고 그 결과를 국립수산과학원에서 제공하는 정선 해양 관측 자료와 비교, 분석하였다. M-Y 기법은 수직적 혼합을 상대적으로 강하게 모의하였으며 그 결과로 저층수온이 높게 형성되었다. 높은 저층 수온은 탁도를 높게 설정하면 완화되지만 표층 수온이 높아지는 단점이 있다. KPP 기법은 M-Y 기법보다는 수직 혼합을 약하게 모의하고 이 약한 수직 혼합 때문에 황해 연안을 따라 형성되는 조석전선을 잘 재현하지 못하였으나, 저층 수온은 관측 수온에 더 가깝게 재현하였다. 결과적으로 황해 3차원 해양순환 모델실험에서 M-Y 기법은 수직 혼합이 잘 되어 표층과 저층의 수온 차이가 작게 나타나고, KPP 기법은 이와 반대로 모의하였다. 탁도의 영향을 표현하는 Jerlov 수형은 높을수록 일사량이 낮은 수심까지만 투과되어 성층을 잘 표현하였고, 낮을수록 깊은 수심까지 일사량이 투과되어 표층과 저층의 수온차를 작게 모의하였다.

• International Journal of Fluid Machinery and Systems
• /
• 제3권3호
• /
• pp.227-234
• /
• 2010

Numerical analyses have been performed to investigate the effects of geometric parameters of a straight groove micromixer on mixing performance and pressure drop. Three-dimensional Navier-Stokes equations with two working fluids, water and ethanol have been used to calculate mixing index and pressure drop. A parametric study has been carried out to find the effects of the number of grooves per cycle, arrangement of patterned walls, and additional grooves in triangular dead zones between half cycles of grooves. The three arrangements of patterned walls in a micromixer, i.e., single wall patterned, both walls patterned symmetrically, and both walls patterned asymmetrically, have been tested. The results indicate that as the number of grooves per cycle increases the mixing index increases and the pressure drop decreases. The microchannel with both walls patterned asymmetrically shows the best mixing performance among the three different arrangements of patterned walls. Additional grooves confirm the better mixing performance and lower pressure drop.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2002년도 제18회 학술발표대회 논문초록집
• /
• pp.18-23
• /
• 2002

Liquid phase mixing of impinging injector is a resultant byproduct from the momentum exchange between a pair of impinging jets and penetration of opponent jet. Principal aim of the present study is revealing the liquid phase mixing mechanism of split triplet impinging injection sprays, and thus extending our understanding on this particular injection element. Overall mixing extent is estimated from patternation tests by the use of purified tap water and kerosene to simulate the real propellant components, respectively, and with the liquid jet momentum ratio, a controlling mixing parameter, in the range of 0.5 to 6.0. Emphasis is placed on the effect of liquid sheet superposition and disintegration, and the results with detailed spray visualization revealed the fact that superposed liquid sheet disintegration is the main pathway of liquid phase mixing of split triplet impinging injector to yield enhanced mixing qualities.

• Journal of the korean society of oceanography
• /
• 제36권3호
• /
• pp.59-71
• /
• 2001

In order to investigate the temporal variability of dissolved and particulate trace metals in the Han River, water samples were collected intermittently at two sites for 3 years (August 91 to December 94). Surface seawaters covering the range of salinity were also collected at the estuarine region to evaluate the role of estuary for the riverine fluxes of trace metals within the estuary during October 95 and 96. During the study period, dissolved metal concentrations in riverwaters varied by a factor of 5-10 for Fe, Ni, Co and Cu and 50-100 for Mn, Cd and Pb depending upon the water level; high concentration during the low water and low concentration in high water period except for Fe. The concentration of dissolved Fe increased with increasing water discharge. These concentration-discharge relationships of the studied trace metals are explained by the successive dilution of waters from two different origins, which can be presumably identified as anthropogenic discharges and watershed flushing. Although estuarine waters at early mixing region were not collected due to the difficulty of sampling, mixing behaviors of metals were inferred from the concentration-salinity relationships through the laboratory mixing experiment and field sampling, and distribution coefficients between dissolved and labile particulate phases. It is suggested that the Han River estuary plays a role of accumulating Fe, Mn, Co and Pb from riverine sources due to high turbidity caused by strong tidal current, whereas this system serves as a source of dissolved Cd due to release caused by extended residence time of riverine particles.

• 한국환경과학회지
• /
• 제1권2호
• /
• pp.15-23
• /
• 1992

Development of cumulus is studied by numerically integrating the equation of motion equations of conservation for water vapor mixing ratio, and the thermodynamic energy equuation. We use the terrain-following coordinate system called z'-coordinate system, in which we can easily treat any calculation domain with terrain configuration such as mountains. The model domain of calculation is restricted vertically to 4.Skin and horizontally to 100 km, has a bell-type mountain in the centeral part. Four cases are considered, one in a neutral environment, second in a slightly stable environment, third in a environment decreasing water content with low value of initial water vapor mixing ratio, the fourth in a case with higher vapor gradient. The more the atmosphere is unstable, the more cumulus develops easily and the more water vapors is abundant, the more cumulus develops easily too. More detailed cloud microphysics parameterizations and wet deposition must be conridered to use in air pollutants prediction model.

• 대한방사선기술학회지:방사선기술과학
• /
• 제24권2호
• /
• pp.53-57
• /
• 2001

The purpose of this study is to investigate the contamination rate of barium sulfate suspension made in the exposed state in usual circumstances. This study was performed in four university hospital using the contrast media by barium sulfate powder. The specimen were detected at dispensing water, agitator and mixing tank. We also classified the suspension into general bacteria, mycete, and Bacillus coli infection. The tap water were used to dispense water in the all hospitals. Bacillus colt were not detected in the all. General bacteria and mycete were not detected in the one specimen, but detected in two specimen over defined value. In the contamination rate of agitator, mixing tank, and the manufactured, Bacillus coli were not detected in all. However, general bacteria and mycete were detected too numberous to count. In conclusion, the refined water must be used in dispensing water in manufacturing suspension. The disinfectant is also used in washing the agitator and mixing tank for sterilization. Hand washing is indispensible to manufacturing suspension for preventing from infection.

• Ocean and Polar Research
• /
• 제44권3호
• /
• pp.191-207
• /
• 2022

Using the results of CTD casts made in Spring from 2017 to 2021, in this study we investigated the water mass distribution and occurrence of temperature inversion in the western seas of Jeju Island in spring. The distribution of water masses was characterized by cold and fresh water in the northwest and warm and saline water in the southeast, forming a strong thermohaline front running in the southwest-to-northeast direction. Strong temperature inversion mainly occurred in the frontal boundary when the cold water intrudes beneath the warm water at depths of 30-50 m. Analysis of the mixing ratio demonstrated that Jeju Warm Water is dominantly distributed in the western seas of Jeju Island, but its ratio can be modified depending on the southward extension of Yellow Sea Cold Water (YSCW). Results of in situ measurement showed that in 2020, the YSCW largely expanded to the western seas of Jeju Island, occupying approximately 40 % of the mixing ratio. Due to the expansion of YSCW, a strong thermohaline front was formed in the study area, thereby causing thick and strong temperature inversion. On the other hand, in 2018 the mixing ratio of YSCW was minimum (~18%) during the study period of 2017-2021, and thus a relatively weak frontal boundary was formed, without the occurrence of temperature inversion. The observational results also suggest that the interannual changes of water mass distribution and the associated temperature inversion in the western seas of Jeju Island are closely related with wind-driven Yellow Sea circulation in spring, which is the summer monsoon transition period.

• 콘크리트학회논문집
• /
• 제27권4호
• /
• pp.419-426
• /
• 2015

본 연구는 지하식 LNG 저장탱크의 시공에 앞서 연약지반의 개량을 위하여 현장 원위치의 흙과 시멘트, 벤토나이트 등을 사용하는 소일-시멘트 연속벽체를 효과적으로 시공하는 SMW 공법에 대한 배합설계 및 현장적용 사례를 실험적으로 규명하기 위한 것이다. 현장조건을 고려하여, 보통 포틀랜드 시멘트와 벤토나이트를 주재료로 선정하였고, 흙의 단위용적중량은 $1,833kg/m^3$을 적용하였으며, 이에 따른 물-시멘트비 4종류와 배합속도 3수준을 대상으로 블리딩 및 압축강도 실험을 실시하였다. 실험은 실내실험 및 현장적용 사례로 나누어 수행되었으며, 실험을 통하여 얻은 결론은 다음과 같다. (1) 물-시멘트비가 감소할수록, 배합속도(rpm)이 증가할수록, 블리딩량 및 블리딩율이 감소하는 것으로 나타났다. (2) 물-시멘트비 150% 이하에서 현장적용강도(1.5 MPa)를 만족하였으며, 현장 코아강도는 공시체 강도에 비해 8~23% 증가하였다. 따라서 적용현장 조건을 고려하여 단위시멘트량 $280kg/m^3$, 벤토나이트 $10kg/m^3$, 물-시멘트비 150%, 그리고 배합속도 90 rpm을 현장시공의 최적배합으로 제안하였으며, 현장적용 사례의 실험결과로부터 요구되는 성능을 만족하였다.