• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.6
• /
• pp.353-358
• /
• 2016

In this paper, we have studied about the optimum fabrication condition of the printed Indium Tin Oxide (ITO) layers for the electrical resistance-type sensor application. We have investigated on the substrates surface treatments, mixing ratio of organic binder/ITO powder, and viscosity of the printing paste to determine the optimum condition of the screen printed ITO layer. Also, we found that the printing condition is closely related with the sensor performance. To know the feasibility of printed ITO layer as an electrical resistance-type sensor, we have fabricated the ITO sensors with a printed and sputtered ITO layers. The printed ITO films revealed $10^2$ times higher sensitivity than the sputtered ITO layer. Also, the sputtered ITO layer exhibited an operating temperature of $127^{\circ}C$ at the operating voltage of 5 V. While, in case of the printed ITO layer showed the operating temperature of $27.6^{\circ}C$ in high operating voltage of 30 V. We found that the printed ITO layer is suitable for the various sensor applications.

• Fire Science and Engineering
• /
• v.22 no.3
• /
• pp.188-193
• /
• 2008

Numerical simulation was carried out for a propane fire of mass transfer rate 3g/m^2-s$ on a 1m high vertical wall. The objectives of this study are to confirm the outcomes of evaluation of the simulator through simulation of natural convection, and to compare the results of the wall fire with those of previous studies. It was confirmed that the simulated boundary layer was laminar at C_s=0.2$ while it was turbulent at C_s=0.1$. The z direction velocity showed lack of turbulent mixing as seen in the natural convection case, and the profiles of temperature and velocities were in relatively good agreement with those of experiment and previous simulation. It was found that the air entrainment into the boundary layer was well predicted.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.413-419
• /
• 2009

As the refractive index of the prism layer becomes higher, the optical performance of the prism sheet gets better and the efficiency of the LCD backlight unit is improved. In order to increase the refractive index of the prism layer, the ultraviolet curing type resins were prepared by mixing high refractive index materials containing aromatic groups and the multi-functional reactive diluents. By using 9,9-bis [4-(2-acryloyloxyethoxy)phenyl] fluorene, the refractive index of the prism layer was increased up to 1.58 and the brightness of the backlight unit was improved. Since the light source used in the backlight unit caused the yellowing in the prism sheet and deteriorated the brightness accordingly, the hindered amine light stabilizer was used to improve the yellowing resistance successfully.

• The Korean Journal of Ceramics
• /
• v.5 no.1
• /
• pp.44-49
• /
• 1999

In order to improve the oxidation resistance of $Ti_3Al$, Ti-25at.%Al composites containing dispersed particles of 15wt.%SiC were prepared by a tubular mixing-spark plasma sintering method. The sintered composites had $Ti_3Al$, SiC, $Ti_5Si_3$ and TiC. The presence of $Ti_5Si_3$ and TiC indicates that some of SiC particles reacted with Ti to from more stable phases. From oxidation tests at 800, 900 and $1000^{\circ}C$ under 1 atm of pure oxygen, it was found that the oxidation rate of Ti3Al was effectively reduced by the addition of SiC. The scale was primarily composed of an outer $TiO_2$ layer having some $Al_2O_3 $islands, an intermediate relatively thick $Al_2O_3 $ layer, and an inner $TiO_2+Al_2O_3+SiO_2$ mixed layer. Beneath the scale, Kirkendall voids were seen.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.755-759
• /
• 2008

For the development of a new white dielectric layer in plasma display panel, different $TiO_2$ types as a filler was add to the $Bi_2O_3$-BaO-ZnO glass matrix. The reflectance and dielectric constant of dielectric have been investigated as a function of the mixing content (rutile and anatase), and sintering temperature. The reflectance of dielectric sintered at the 520$^{\circ}C$ appeared most highly and suitable in terms of the adhesion and reflectance of the soda-lime glasses. Also, the thermal expansion coefficient of dielectric was found to be $85.6\times10^{-7}/K$, which was similar to that of the soda-lime glasses. Especially, the dielectric constants were not increased with increasing of $TiO_2$ filler contents.

• 한국해양학회지
• /
• v.12 no.1
• /
• pp.7-12
• /
• 1977

Vertical mixing in the ocean affects the formation of water masses as well as the vertical distribution of nutrients and dissolved substances. this study is to investigate the effect of stability on the intensity of vertical transfer in the case of shallow and straitfied channel. It is found that the relation of the stability and vertical turbulent diffusion is given by K$\sub$z/ = -${\beta}$-(c+${\beta}$) / ${\alpha}$(E-1/${\alpha}$) where K$\sub$z/ and E denotes the vertical turbulent diffusion coefficient and stability, respectively. The empirical coefficients ${\alpha}$, ${\beta}$ and c depend on the magnitude of vertical components and stability, i.e., through thermocline intensity. The study indicates that the diffusivity of the surface mixed layer is (K$\sub$z/)=300∼1,200$\textrm{cm}^2$/sec, the thermocline layer is (K$\sub$z/)= 50∼200$\textrm{cm}^2$/sec and the cold layer is (K$\sub$z/)=200∼600$\textrm{cm}^2$/sec based on near- minimum least-squares error estimates from the regression analysis. An important result of our study comes out that the model is in accordance with the general trends of the effect of stability on the vertical turbulent diffusion coefficients in the case of shallow and strongly stratified channel.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.3
• /
• pp.1-8
• /
• 1997

The surface properties after plasma etching of TiW alloy using the chemistries of BCl$_{3}$ and SF$_{6}$ gases with varying mixing ratio have been investigated using XPS(X-ray photoelectron spectrocopy). The elements existed on the etched sampled have been extracted with BCL$_{3}$/SF$_{6}$ ratio and their chemical binding states have also been analysed. It was confirmed that the thickness of native oxide formed on the TiW films is thinner than 10nm by using Ar sputtering. At the same time, the roughness of etched surface has been esamnied using AFM (atomic force microscopy). on the basis of the basis of this results, the relations between the caanges of oxygen contents detected by XPS and the rouhness of etched surface have been discussed. And the etch rate and etched profile of Tiw films have been examined and the changes of the etch rate and etched prfile have been discussed with XPS results. From XPS results, the role of passivation layer consisted of Ti-S compound with XPS results. From XPS results, the role of passivation layer consisted of Ti-S compound has been proposed. Ti-S compound seems to make a role of passivation layer that surpresses Ti-O formation.ion.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.5
• /
• pp.361-369
• /
• 1997

In order to investigate the abundance and transboundary fluxes of air pollutants over the Yellow Sea, airborne measurements were made aboard the SF-600 aircraft (Pan-Asia Engineering) in March, 1996. The data presented in this paper are preliminary results and airborne experiment will be carried out until 1999. The vertical profile of relevant meteorological parameters such as temperature, water vapor, wind direction and wind speed were also observed at Taean. Mixing layer height was about 1000~1100m during the flights. The SO$_2$ and NO$_{x}$ concentrations were 3~6 ppb and 5~7 ppb below 1000 m, within 1 ppb and 3~5 ppb at 1000~2000m, respectively. Backward trajectory analyses were also carried out. A mathematical method by Lelieveld et al.(1989) was used to estimate the flux of air pollutants through the planetary boundary layer of Yellow Sea area. Transboundary fluxes were calculated using the measurement results with respect to the pollutants concentration, depth of the planetary boundary layer, wind speed and wind direction. The estimated transboundary flux of SO$_2$through the western boundary of Korea was about 39~42 tons/hour.r.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.4
• /
• pp.27-39
• /
• 1989

The effect of gas mixing ratios during gas nitrocarburizing treatment on the formation of compound layer and the mechanical properties has been studied for hot work tool steel by using a combined heat treating technique. The thickness of compound and diffusion layers has been shown to grow as a parabolic relation with increasing the amount of ammonia at a given flow quantity of $CO_2$ gas. The compound layer consists mainly of ${\varepsilon}-Fe_3$(C, N) with small amounts of ${\gamma}^{\prime}-Fe_4N$ and ${\alpha}$-Fe. The combined heat treated hot work tool steel has shown that the thickness of compound layer increases with increasing nitrocarburizing time, but the rate of growth slows down as gas nitrocarburizing time goes more than two hours. Tensile properties have given a remarkable improvement. In particular, the wear resistance of combined heat treated hot work tool steel has exhibited an improvement of about 165% greater than that obtained from conventional quenching and multi-tempering treatments.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.4
• /
• pp.285-297
• /
• 1997

Finned segment, with which are lined inner wall of the turbine combustors, are subject to severe degradation when they are exposed to a hostile environmment at elevated temperature. To protect the finned segment from this environment and to maintain good mechanical properties of components at high temperature, they are preferred to be coated. The most governing factor for the durability of coatings used in the high temperature is the microstructure of coatings; these are splat from, distibution of microcacks, size and distribution of pores, thickness of coating layer, adhesion between coating layer, and oxidation of band coating. In this study, based on the evaluation of the imported finned segment, new finned segment segment was manufactured with optimum plasma spraying parameters, and their properties were examined. Using $ZrO_2(8wt$Y_2O_3)$,/TEX> powder for ceramic coating and 67Ni-22Cr-10Al-0.5Y mixing powder for bond coating, thickness of ceramic and bond coating layer were varied in order to find optimum condition, the results showed that B2T4(bond coating : 100~250$\mu\textrm{m}$, ceramic coating : 250~300$\mu\textrm{m}$) was the best among the specimens tested. Compared to the imported finned segment, B2T4 has better bond strength, hardness, and isothermal and cyclic oxidation resistance.