• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2083-2099
• /
• 1991

본 연구에서는 다른 실험 조건은 일정하게 유지하면서 아래 벽면의 표면조도 를 체계적으로 변화시켜 표면조도가 후향계단 뒤의 재부착 흐름 및 재발달경계층에 미 치는 영향을 조사하고자 하며 구체적인 내응은 다음과 같다. (1) 표면조도가 재부착 길이와 재발달경계층에 미치는 영향의 조사. (2) 표면조도가 평균속도와 난류량 분포 에 미치는 영향의 조사. (3) 여러 종류 표면조도 변화에 따른 재부착길이와 재발달 경 계층 회복에 미치는 영향과 결과의 상호 비교.

• 한국해양학회지
• /
• 제20권1호
• /
• pp.12-21
• /
• 1985

하계 동지나해에서 가장 중요한 해양학적 현상들을 재검토하였다. 계절적 수 온약층 상부 표층수는 태양가열과 주로 양자강으로 부터의 담수의 유입 그리고 하 계 계절풍에 의해 지대한 영향을 받고 있다. 수온약층 하부층에는 여러가지 해양역 학적 작용에 대한 질량장의 조정에 의해서 몇가지 분명히 구별되는 수괴들 즉 쿠로 시오 표층수, 서북태평양 중앙수, 황해저층 냉수등이 잠입되고 있다. 잠입된 황해저 층 냉수와 서북태평양 중앙수와의 전선역 혼합이 제주 남방 대륙붕상의 저층에서 일어난다. 이 혼합수는 제주 주변과 한국 남해안 중저층의 해수 특성에 커다란 영 향을 미칠 것으로 보인다.

• 환경영향평가
• /
• 제21권5호
• /
• pp.665-681
• /
• 2012

This study investigates the influence of anthropogenic heat (AH) release on urban boundary layer in the Gyeong-In region using the Weather Research and Forecasting model that includes the Seoul National University Urban Canopy Model (SNUUCM). The gridded AH emission data, which is estimated in the Gyeong-In region in 2002 based on the energy consumption statistics data, are implemented into the SNUUCM. The simulated air temperature and wind speed show good agreement with the observed ones particularly in terms of phase for 11 urban sites, but they are overestimated in the nighttime. It is found that the influence of AH release on air temperature is larger in the nighttime than in the daytime even though the AH intensity is larger in the daytime. As compared with the results with AH release and without AH release, the contribution of AH release on urban heat island intensity is large in the nighttime and in the morning. As the AH intensity increases, the water vapor mixing ratio decreases in the daytime but increases in the nighttime. The atmospheric boundary layer height increases greatly in the morning (0800 - 1100 LST) and midnight (0000 LST). These results indicate that AH release can have an impact on weather and air quality in urban areas.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.285-288
• /
• 2008

본 연구는 연료(수소)층과 산화제(공기)층의 사이에 불활성기체(질소)또는 연료(수소)를 평행분사하는 수치해석을 다루고 있다. 수치해석을 위해서 완전 보존되는 비정상 2차 시간정확도법과 2차 TVD방법이 유한 체적법과 사용되었다. 결과는 3가지 종류로 구성되어있다. 첫째는 연료와 산화제의 단일 혼합층이고, 둘째는 연료와 산화제의 사이에 불활성기체를 분사하는 방식이며, 세 번째는 연료와 산화제의 사이에 연료를 분사하는 방식이다. 전체 유동층의 수직두께는 4cm이며 삽입된 중간층의 두께는 1,2,4mm의 세가지 경우에 대하여 계산하였다.

• Ocean and Polar Research
• /
• 제32권3호
• /
• pp.331-336
• /
• 2010

The CREAMS (Circulation Research of the East Asian Marginal Sea) survey in 1999 revealed a sharp mid-depth discontinuity of the phosphate:silicate ratio in all basins of the East/Japan Sea. Incidentally, this discontinuity layer corresponds to the oxygen minimum layer. Directly below the discontinuity layer, oxygen concentration is increased. This increase in oxygen concentration is interpreted as a proof of intermediate water formation. Oxygen minimum indicates that the water parcel is old and stable against mixing. So it seems be an efficient barrier to vertical exchange of materials. This means that, once materials enter the lower domain, they rarely return to the upper domain. Therefore, the biogeochemistry of the East/Japan Sea depends heavily on material input through the Korea Strait, and flux is expected to be sensitive to the climate change. As a result, the East/Japan Sea ecosystem seems vulnerable to tipping (regime shift), which occurred on a decadal time scale.

• 한국표면공학회지
• /
• 제35권1호
• /
• pp.17-32
• /
• 2002

Electroplating methods by molten salts and non-aqueous melts were employed for aluminium coating on STS 316L stainless steel. After coated with Ni or non-coated surface on stainless steel, Al pulse plating was carried out in two different types of electrolytes at room temperature. The Al layer from $AlCl_3$-TMPAC melts could not obtain appreciable thickness for engineering application due to chemical reactions between deposits and moisture of air. However, The Al coating by pulse plating in the Ethylbenzene-Toluene-$AlBr_3$ systems was found to be solid coating layer with a few $\mu\textrm{m}$ scale. The conductivity of Ethylbenzene-Toluene-$AlBr_3$ electrolyte was as functions of time and agitation. By seven days exposure after mixing of the electrolyte, Al-deposited layer shows uniform and near by pore-free with high current density (higher than 30mA/$\textrm{cm}^2$). The roughness and imperfection of coating layer were decreased with a increasing agitation speed. It was found that the optimum condition for the Al pulse plating on the 316L stainless steel was a 400mA peak current, duty cycle, $t_{on}$ $t_{ off}$=3ms/1ms, and a current density of 30mA/$\textrm{cm}^2$.

• 한국주조공학회지
• /
• 제28권6호
• /
• pp.282-287
• /
• 2008

The effect of CaO mold on the formation of reaction layer was investigated. CaO mold was prepared by mixing of Colloidal silica($NALCO^{(R)}$ 1130) and an $ZrO_2$, CaO at room temperature. The dried at $20{\pm}3^{\circ}C$, 75% humidity for 12hrs. Sample was prepared from the Cp-Ti(grade-2) and melted by high frequence induction melting system in the vacuum condition. The react ion layer of Ti was confirmed by optical microscopy, microhardness(Hv) and X-ray diffraction. Thickness of reaction layer using the CaO stabilized ZrO2 was thinner than the CaO added ZrO2. And thickness of reaction layer were decreased with decreasing pH of slurry. CaO addition in the slurry could not controlled reaction between molten Ti and investment mold. On the other hand, the CaO chemical bonded ZrO2 by stabilization treatment could controlled reaction between molten Ti and investment mold.

• Membrane and Water Treatment
• /
• 제3권2호
• /
• pp.113-121
• /
• 2012

Up-flow multi-layer bioreactor (UMBR) is a hybrid system using dual sludge that consists of an up-flow multi-layer bioreactor as anaerobic/anoxic suspended growth microorganisms followed by an aeration tank. The UMBR acts as a primary settling tank, anaerobic/anoxic reactor, thickener which requires low energy due to mixing by up-flow stream. This study focused on using a pilot UMBR plant with capacity of 20-30 $m^3$/day for domestic wastewater in HCMC. HRTs of UMBR and aeration tank were 4.8 h and 7.2 h, respectively. The average MLSS of UMBR ranged from 10,000-13,600 mg/l SS. Internal recycle rate and sludge return were 200-300% and 150-200%, respectively. The results obtained from this study at flow rate of 20 $m^3$/day showed that removal of COD, SS, TKN, N-$NH_4$, T-N, and color were 91%, 87%, 86%, 80%, 91% and 91%, respectively.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
• /
• pp.108-109
• /
• 2011

유기태양전지를 제작 시에 요구되는 것 중 하나는 active layer의 thermal annealing이다. Thermal thermal annealing 없이는 P3HT의 self-organization이 잘 이뤄지지 않아 비정질의 모습을 보인다. 또한 low band-gap이나 열에 취약한 물질을 사용 시에 태양전지 효율이 낮아지게 된다. 이 점을 착안하여 Active layer에 사용되는 유기용매의 solvent vapor pressure 차이를 이용하여 co-solvent가 되도록 mixing하여, co-solvent로 poly(3-hexylthiopene)(P3HT):[6,6] - phenyl $C_{61}$-butyric acid methyl ester (PCBM)를 blending 하여 active layer로 사용하였으며, 유기태양전지 디바이스 제작 결과 thermal thermal annealing 없이 2.8%까지 도달하였다. X-Ray Diffraction(XRD)과 Atomic Force Microscopy(AFM)를 통하여 P3HT의 결정화가 이루어 졌음을 확인하고 이를 통해 active layer의 thermal annealing이 없이도 P3HT의 self-organization이 이뤄짐을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제31권6호
• /
• pp.408-411
• /
• 2018

We fabricated highly flexible Mn-doped $SnO_2$ (MTO)/Ag/MTO/polydimethylsiloxane (PDMS)/MTO multilayer transparent conducting films. To reduce refractive-index mismatching of the MTO/Ag/MTO/polyethylene terephthalate (PET), index-matching layers were inserted between the oxide-metal-oxide-structured films and the PET substrate. The PDMS layer was deposited by spin-coating after adjusting the mixing ratio of PDMS and hexane. We investigated the effects of the index-matching layer on the color and reflectance differences with different PDMS dilution ratios. As the dilution ratio increased from 1:100 to 1:130, the color difference increased slightly, while the reflectance difference decreased from 0.62 to 0.32. The MTO/Ag/MTO/PDMS/MTO film showed a transmittance of 87.18~87.68% at 550 nm. The highest value of the Haacke figure of merit was $47.54{\times}10^{-3}{\Omega}^{-1}$ for the dilution ratio of 1:130.