• 유기물자원화
• /
• 제12권1호
• /
• pp.84-93
• /
• 2004

본 연구는 생물학적 처리공정의 하나인 SBR을 이용하여, 양돈폐수중의 유기물과 질소, 인의 동시 제거를 목적으로 적정의 수리학적 체류시간(HRT)과 반응기간 중 교반/폭기 시간비(M/A) 및 적정의 교반/폭기 시간비에서의 외부탄소원의 주입기간(Injection Time)에 따른 변화에 따른 실험 결과로부터 다음과 같은 결론을 얻었다. (1) $NH_4{^+}-N$의 제거효율은 M/A가 0.0/22.0일 때(Run 1) 가장 효율이 좋았으며, 외부탄 소원을 주입했을 경우 탈질균의 증식으로 인해서 질산화가 잘 이루어지지 않기 때문에 주입시간이 길어질수록 증가하였다. T-N의 제거효율은 M/A가 증가할수록, 외부탄소원 주입시간이 길어질수록 증가하였다. (2) T-P의 제거효율은 운전조건에 따라 큰 차이를 보이고 있으며, M/A가 증가할수록 제거효율은 증가하였으며, 외부탄소원의 주입기간을 두고 보았을때, 주입기간을 짧게 할 경우 탈질균의 증식으로 인해서 탈질이 더 효율적으로 이루어지기 때문에 그 제거효율은 증가하였다. (3) 총 반응시간 22시간 중 M/A 16.5/5.5, 무산소 기간의 16.5시간 중 15시간동안 외부탄소원을 주입했을 경우(Run 4-1)의 운전조건에서 유기물 및 질소 제거에 가장 효율적이었다. 각각의 효율을 살펴보면, $COD_{Cr}$, $COD_{Mn}$ 그리고 $BOD_5$인 경우, 각각 90.6%, 87.7% 그리고 96.1%이고, T-N의 경우 86.6%, T-P인 경우는 84.5%로 나타났다.

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.31-38
• /
• 2009

Supercharging system was adopted to investigate the influence of boost pressure on operating range and exhaust emissions by using a supercharger at low temperature diesel combustion (LTC) condition in a 5-cylinder 2.7 L direct injection diesel engine. The experimental parameters such as injection quantity, injection timing, injection pressure and exhaust gas recirculation (EGR) rate were varied to find maximum operating range in LTC condition. As a result of adopting increased boost pressure in LTC, wider operating range was achieved compared with naturally aspirated condition due to increased mixing intensity. Increased boost pressure resulted in lower hydrocarbon (HC) and carbon monoxide (CO) emissions due to increased swirl rate and mixing intensity, which induced complete combustion. Moreover, increased boost pressure in LTC resulted in much lower soot emissions compared with high speed direct injection (HSDI) condition.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.93-101
• /
• 2003

The extinction of unsteady diffusion flame was experimentally studied in an opposing jet counterflow burner using diluted methane. The stabilized flame was perturbed by linearly varying velocity change that was generated by pistons installed on both sides of the air and fuel stream. As the results, the extinction of unsteady flame is dependent not only on the history of unsteadiness, but also on the initial condition. We found that there are several unsteady effects on the flame extinction. First, the extinction strain rates of unsteady cases are extended well beyond steady state extinction limits. Second, as the slope of the strain rate change increases, the unsteady extinction strain rate becomes larger. Third, the extension of unsteady extinction strain rate becomes smaller as the initial strain rate increases. We also found that the extension of the extinction limit mainly results from the unsteady response of the reaction zone because there is no retardation effect of a mixing layer for our experimental condition.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.262-268
• /
• 1998

This research is to examine the selected method of optimal mixing proportion and cost analysis in the super flowing concrete. As confined water $ratio($\beta_p$)$ and K is introduced, itis to establish optimal mixing design of super flowing concrete according to the steps of paste, mortar and concrete. From paste and mortar test, it was led to $$\beta_p$$ and $K_p$satisfying the optimum condions depending on the kinds of binders. Then $$\beta_p$$ and $K_p$ is reflected to the mix condition of super flowing concrete. The result of test, the mix condition of super flowing concrete satisfied the quality performance of concrete with adjustment of additional rate of the superplasticizer. Besides, in case of design strength $350kg/\textrm{cm}^2$ of concrete, material cost in super flowing concrete is able to be reduced 5~16% in replacement of fly ash 30% in ordinary portland cement and slag cement.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.30-36
• /
• 2020

In SMART, the flow mixing header assembly (FMHA) is used to mix the coolant flowing into the reactor core to maintain a uniform temperature. The FMHA is designed to have enough stiffness so the resonance with reactor internal structures does not occurs during the pipe break and the seismic accidents. Since the gap between the FMHA and the core support barrel assembly is very narrow compared with the diameter of FMHA, the hydrodynamic mass effect acting on the FMHA is not negligible. Therefore the hydrodynamic mass characteristics on the FMHA are investigated to consider the fluid and structure interaction effects. The result of modal analysis for the dry and underwater conditions, the natural frequency of primary vibration mode for the horizontal direction is reduced from 136.67 Hz to 43.76 Hz. Also the result of frequency response spectrum seismic analysis for the dry and underwater conditions, the maximum equivalent stress are increased from 13.89 MPa to 40.23 MPa. Therefore, reactor internal structures located in underwater condition shall consider carefully the hydrodynamic mass effects even though they have sufficient stiffness required for performing its functions under the dry condition.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.920-925
• /
• 2008

In this presentation, a leaching experiment which is followed the pH changes(pH=4, pH=7) and the mixing rates(1%, 3%, 5%, 7%) was carried out to examine the arsenic reduction effects and the leaching characteristics on arsenic contaminated soil after stabilization treatment in which 5 materials were used as stabilization agencies, i.e. ZVI(zero valent iron), blast furnace slag, steel refining slag, quick lime, and oyster shell meal. Except for blast furnace slag, the arsenic removal rate increased as the mixing rate increases of stabilization agencies. Arsenic leaching concentration was indicated that pH=7 condition is higher than pH=4 condition. This result shows because arsenic immobilization reaction increases as pH decreases, and arsenic adsorption takes place as pH decreases.

• 한국환경보건학회지
• /
• 제19권2호
• /
• pp.1-9
• /
• 1993

In public water supply systems, Alum and/or PAC being used as a coagulant. It is well known that their use increased frequently the concentration of residual aluminum in filtered water upon operating conditions. This study was conducted to find the optimum conditions that both the concentration of residual aluminum and turbidity are minimized by changing such factors as pH, temperature, alum dosage, mixing rate, alkalinity and hardness. The results can be summarized as follows: The pH values for the minimum concentration of residual aluminum and turbidity as a given experimental condition were found at pH 6 and pH 7 respectively, the apparent clarity was best at pH 8. The floc settling rate was the greatest at pH 6.5, but the turbidity was high at the same condition. The more alum dosage, the higher the concentration of residual aluminum. However the alum dosage less than 15 mg/l tend to decrease in turbidity. Restabilization and enmeshment occurred near 15 mg/l and 20 mg/l of alum dose respectively. With the increase of mixing rate (rapid and slow), the concentration of residual aluminum and turbidity are increased and the same trend was found in increment of mixing time. At low water temperature, the concentration of residual aluminum was decreased, but turbidity was increased. It was confirmed that alkalinity had an effect on the coagulation efficiency, but hardness did not.

• 한국응용과학기술학회지
• /
• 제15권1호
• /
• pp.25-33
• /
• 1998

Photoresist is defined as substance that makes chemical changes in its solubility, colouring and hardening by light energy. In this study, photosensitive photoresists of the positive type for a printing plate were studied. PF, o-, m-, p-CF resins as a matrix resin were synthesized at an identical condition. Photoresists were prepared by mixing NDS derivatives with a matrix resin at various mixing ratios. Characteristics of photoresists were studied by yield method of residual using solubility and Optical microscope was also analyzed. Prepared photoresist using NDS derivatives shows excellent photosensitivity and solubility compared with commercial product. The mixing ratio of 1:4(by mass) of NDS derivative[III] and m-CF resin shows the highest dissoultion rate among others. In addition, photoresist was obtained at this condition resulted in the superior sensitivity and contrast.

• Korean Chemical Engineering Research
• /
• 제44권5호
• /
• pp.547-554
• /
• 2006

응집공정에서 교반조건과 응집제 주입농도에 따른 알루미늄 가수분해종 변화에 대한 실험결과 다음과 같은 결론을 얻을 수가 있었다. 알루미늄 표준용액을 이용하여 모노머성 알루미늄과 페론 반응을 살펴본 결과 반응초기에 급격한 반응률을 보이며 반응시간 3분 정도에 평형에 도달함을 알 수 있었다. 순수의 경우 교반시간에 따른 영향은 거의 나타나지 않고 있으며 거의 일정한 반응률을 보이고 있었다. 상수원수의 경우 입자상 물질과 유기물의 존재함에 따라 응집제 주입시 수중에서 형성되는 알루미늄 가수분해종이 입자상 물질 및 유기물과 우선적으로 반응하기 때문에 형성되는 알루미늄 가수분해 종에 대한 반응률이 교반시간에 따라 다르게 나타났다. 응집제 주입량이 증가할수록 페론과 반응율이 빠르게 일어나나 일정한 시간이 경과한 후에 반응율을 살펴보면 응집제 주입량이 증가할수록 반응이 느리게 나타났다. 순수의 경우 교반시간에 따른 Ka 값은 교반시간이 증가할수록 Ka 값은 감소함을 알 수 있으며 응집제 주입량의 영향은 크게 나타나지 않고 있다. 그러나 Kb의 경우 응집제 주입량이 증가할수록 반응속도 상수값이 낮아지는 경향을 보이고 있으며, 마찬가지로 교반시간이 증가할수록 Kb 값은 감소함을 알 수 있다. 상수원수를 사용한 경우 순수와 마찬가지로 교반시간에 따른 Ka, Kb값 은 교반시간이 증가할수록 감소하였다. 그러나 응집제 주입량이 증가할수록 Ka 값은 감소하였다.

• Korean Chemical Engineering Research
• /
• 제59권1호
• /
• pp.94-99
• /
• 2021

2단 Rushton turbine 날개를 장착한 접시바닥형 교반조 내의 유동 상태가 어떤 회전수에서 변화하는 현상을 찾아냈다. 층류 영역에서는 회전수를 변화시켜도 안정적인 도넛 링이 형성되어 혼합 패턴에 특이한 변동은 관찰되지 않았다. 전이영역에서의 평바닥형 교반조에서는 회전수에 변화를 주어도 두꺼운 2개의 미혼합 도넛 링에 변화가 없는 반면, 접시바닥형 교반조에서는 회전수가 450 rpm이 되면 두꺼운 2개의 미혼합 도넛 링이 아주 얇은 3개의 도넛 링으로 바뀌어 혼합이 개선되었다. 접시바닷형 교반조에서는 Re=138~178의 영역에서 링 모양의 미혼합 영역이 3곳에서 나타났고 그 크기도 컸지만, 평바닥형 교반조에서는 Re=116~176에서 링모양의 미혼합 영역은 2곳에서 나타났으며 그 크기도 작았다. 이러한 현상이 관찰되는 조건은 전이영역으로, 방해판을 부착하였을 때가 방해판이 없을 때와 비교하여 동력수가 커지기 시작하는 영역임을 알 수 있었다. 또한 교반 레이놀즈수가 300을 넘어 유동 상태에 약간의 난류가 섞이게 되면, 이 같은 흐름 양상의 단절이 해소되어 완전히 혼합되었다.