• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.519-524
• /
• 2021

The impact properties of two austenitic Fe-23Mn-0.4C steels with different Al contents for cryogenic applications are investigated in this study. The 4Al steel consists mostly of austenite single-phase microstructure, while the 5Al steel exhibits a two-phase microstructure of austenite and delta-ferrite with coarse and elongated grains. Charpy impact test results reveal that the 5Al steel with duplex phases of austenite and delta-ferrite exhibits a ductile-to-brittle transition behavior, while the 4Al steel with only single-phase austenite has higher absorbed energy over 100 J at -196 ℃. The SEM fractographs of Charpy impact specimens show that the 4Al steel has a ductile dimple fracture regardless of test temperature, whereas the 5Al steel fractured at -100 ℃ and -196 ℃ exhibits a mixed fracture mode of both ductile and brittle fractures. Additionally, quasi-cleavage fracture caused by crack propagation of delta-ferrite phase is found in some regions of the brittle fracture surface of the 5Al steel. Based on these results, the delta-ferrite phase hardly has a significant effect on absorbed energy at room-temperature, but it significantly deteriorates low-temperature toughness by acting as the main site of the propagation of brittle cracks at cryogenic-temperatures.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.2
• /
• pp.96-101
• /
• 2021

NaNbO₃:Eu³⁺ phosphor thin films were grown on quartz substrates by radio-frequency magnetron sputtering at a growth temperature of 100 ℃, with subsequent annealing at temperatures of 800, 900, and 1000 ℃. The effects of annealing temperature on the structural, morphological, and optical properties of the thin films were investigated. The NaNbO₃:Eu³⁺ sputtering target was synthesized by a solid-state reaction of raw materials Na₂CO₃, Nb₂O₅, and Eu₂O₃. The X-ray diffraction patterns exhibited that the thin films had two mixed phases of NaNbO₃ and Eu₂O₃. Surface morphologies were investigated by using field emission-scanning electron microscopy and indicated that the grains of the thin film annealed at 1000 ℃ showed irregular shapes with an average size of approximately 300 nm. The excitation spectra of Eu³⁺-doped NaNbO₃ thin film consisted of a strong charge transfer band centered at 304 nm in the range of 240-350 nm and two weak peaks at 395 and 462 nm, respectively, resulting from the ⁷F₀→⁵L₆ and ⁷F₀→⁵H₂ transitions of Eu³⁺ ions. The emission spectra under excitation at 304 nm exhibited an intense red band centered at 614 nm and two weak bands at 592 and 681 nm. As the annealing temperature increased from 800 ℃ to 1000 ℃, the intensities of all the emission bands and the band gap energies gradually increased. These results indicate that the higher annealing temperature enhance the luminescent properties of NaNbO₃:Eu³⁺ thin films.

• Korean Journal of Environmental Agriculture
• /
• v.38 no.1
• /
• pp.47-53
• /
• 2019

BACKGROUND: This experiment was conducted to examine the effects of organic Se concentration and the number of foliar applications on growth characteristics and Se content in rice. METHODS AND RESULTS: A series of multiple foliar applications were performed at (1) 3 times (maximum tillering stage + booting stage + heading stage), (2) 4 times I (effective tillering stage + maximum tillering stage + booting stage + heading stage), (3) 4 times II (maximum tillering stage + booting stage + heading stage + grain filling stage) according to the development stage. Each set of the foliar application plots was treated with 0, 10, 20, 40, 60, 100 ppm of Se and with mixed pesticide ($P^*$ + Se 40 ppm) in which the treatment time was the same as that of the treatment 4 times II. The total cultivation period of rice was 184 days. Se contents in rice (brown rice, white rice) were analyzed by ICP. CONCLUSION: The number of grains per head tended to decrease with increasing concentrations of organic Se in all treatments. However, number of panicles per hill did not show statically significant differences between the 3 times and 4 times I treatments. The grain yield decreased with the 3 times and 4 times II, but there was no significant difference in 4 times I. Se content in brown rice was the highest at 100 ppm Se (5268.64) treatment and lowest at 10 ppm Se ($1269.19{\mu}g{\cdot}kg^{-1}$) treatment. Se content in the polished rice was the highest at 100 ppm Se (5047.33) treatment and lowest at 10 ppm Se ($885.05{\mu}g{\cdot}kg^{-1}$) treatment. The higher selenium was treated, the higher Se content was found in the rice (brown rice, polished rice).

• Geomechanics and Engineering
• /
• v.31 no.2
• /
• pp.167-181
• /
• 2022

Soil liquefaction has been one of the most important concerns in geotechnical earthquake engineering in recent years, due to its damages to structures and its destructive effects. The cyclic liquefaction of silty sands, in particular, remains of great interest for both research and application. Although many factors are known that affect the liquefaction resistance of sands, the effect of fine grain content is perhaps one of the most studied and still controversial. In this study, 48 deformation-controlled cyclic simple shear tests were performed on BS and CS silt samples mixed with 5%, 15% and 30% by weight of Krk085, Krk042 and Krk025 sands in constant-volume conditions to determine the liquefaction potential of silty sands. The tests were carried out at 30% and 50% relative density and under 100 kPa effective stress. The results revealed that the liquefaction potential of silty sand increases with increasing average particle size ratio (D_50sand / d_50silt) of the mixture for a fixed silt content. Furthermore, for identical base sand, the liquefaction potentials of coarse grained sands increase with increasing silt content, while the respective potentials of fine grained sands generally decrease. However, this situation may vary depending on the silt grain structure and is affected by the nature of the fine grains. In addition, the variation of the void ratio interval was shown to provide a good intuition in determining the liquefaction potentials of silty sands, while the intergranular void ratio alone does not constitute a criterion for determining the liquefaction potentials of silty sands.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.11
• /
• pp.1615-1622
• /
• 2014

An accurate assessment of moisture content in feed ingredients is important because moisture influences the nutritional evaluation of feedstuffs. The objective of this study was to evaluate various methods for moisture content determination. In Exp. 1, the weight loss on drying (LOD) of corn, soybean meal (SBM), distillers dried grains with solubles (DDGS), whey permeate, whey powder, spray-dried porcine plasma (SDPP), fish meal, and a mixed diet of these 7 ingredients were measured by oven drying at $135^{\circ}C$ for 2 h. Additionally, the samples were dried at $105^{\circ}C$ for 3, 6, 9, 12, or 15 h. The LOD contents of the DDGS, whey permeate, and whey powder measured by drying at $135^{\circ}C$ for 2 h were greater than the values measured by drying at $105^{\circ}C$ for 3 h (p<0.05). All samples except SDPP (p = 0.70) dried at $105^{\circ}C$ for 6, 9, 12, or 15 h caused more LOD compared with the samples dried for at $105^{\circ}C$ for 3 h (p<0.05). The LOD contents of the individual ingredients were additive when dried at $105^{\circ}C$ regardless of drying time. In Exp. 2, moisture contents of corn, SBM, wheat, whey permeate, whey powder, lactose, and 2 sources of DDGS (DDGS1 and DDGS2) were measured by the Karl Fischer method, oven drying at $135^{\circ}C$ for 2 h, and oven drying at $125^{\circ}C$, $115^{\circ}C$, $105^{\circ}C$, or $95^{\circ}C$ for increasing drying time from 1 to 24 h. Drying samples at $135^{\circ}C$ for 2 h resulted in higher moisture content in whey permeate (7.5% vs 3.0%), whey powder (7.7% vs 3.8%), DDGS1 (11.4% vs 7.5%), and DDGS2 (13.1% vs 8.8%) compared with the Karl Fischer method (p<0.05). Whey permeate and whey powder were considerably darkened as the drying time increased. In conclusion, drying samples at $135^{\circ}C$ for 2 h is not appropriate for determining the moisture content in whey permeate, whey powder, or DDGS as well as the mixed diet containing these ingredients. The oven-drying method at $105^{\circ}C$ for 5 to 6 h appears to be appropriate for whey permeate and whey powder, and at $105^{\circ}C$ for 2 to 3 h for DDGS.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1074-1082
• /
• 2002

Nanocomposite PMN-PT-BT/Ag/MgO was prepared by sintering at $950{\circ}C$ with addition of $AgNO_3$ and MgO sol to the PMN-PT-BT powder sinterable at $1200{\circ}C$. The low-temperature-sinterable PMN-PT-BT/Ag powder prepared by the modified mixed oxide method was calcined at $600{\circ}C$ for 1h and surface modified with the MgO sol of 0-10 wt% and then subjected to consolidation at $850-950{\circ}C$ for 4h under a flowing oxygen. The nanocomposite PMN-PT-BT/Ag/MgO(0.5wt%) sintered at $950{\circ}C$ showed the microstructure with grains of $1-3{\mu}m$, the second phase of MgO of $0.1-0.3{\mu}m$ by SEM and Ag of << $1{\mu}m$ qualitatively by SIMS. It showed the sintered relative density of 99%, the room temperature dielectric constant of 17200, the dielectric loss of 2.1% and the specific resistivity of $5.46{\times}10^{12}{\Omega}{\cdot}cm$. But the PMN-PT-BT/Ag/MgO(0 wt%) nanocomposite sintered at $950{\circ}C$ showed a little better properties : the sintered relative density of 99.5%, the room temperature dielectric constant of 19500, the dielectric loss of 2.1% and the specific resistivity of $7.30{\times}10^{12}{\Omega}{\cdot}cm$.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.3
• /
• pp.187-190
• /
• 2006

In order to produce hemp with low cannabinoids and appropriate fiber yield, seeds of the IH3 (non drug type germplasm) and local variety (drug type cultivar) were mixed to 1:1, 2:1, 3:1 on base of seed weight ratio and cultivated for seed production. In the seed yield trial, the weight of 1000 grains were around 21 g, which was increased in proportion to the ratio of IH3 seeds but seed yield were 100 kg/10a, which were not significantly different by the seeds-mixing ratio. In fiber yield trials with seeds from seed yield trial, fiber yield ranged $193{\sim}198kg/10a$ which was not significantly different by the seeds mixing ratio but the content of THC(${\Delta}$-9-tetrahydrocannabinol) was lowered in proportion to the ratio of IH3 seeds. Variation of THC and CBD (Cannabidiol) level in the 150 plant cultivated with various seed mixing ratio reflected that the percentage of drug and intermediate type were decreased but non drug type were increased in proportion to the ratio of IH3 seeds.

• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.7
• /
• pp.985-993
• /
• 2017

Objective: The objective of this study was to evaluate increasing doses of a novel microbial phytase (Cibenza Phytaverse, Novus International, St. Charles, MO, USA) on standardized total tract digestibility (STTD) of P in canola meal (CM), corn, corn-derived distiller's dried grains with solubles (DDGS), rice bran (RB), sorghum, soybean meal (SBM), sunflower meal (SFM), and wheat. Methods: Two cohorts of 36 pigs each (initial body weight = $78.5{\pm}3.7kg$) were randomly assigned to 2 rooms, each housing 36 pigs, and then allotted to 6 diets with 6 replicates per diet in a randomized complete block design. Test ingredient was the only dietary source of P and diets contained 6 concentrations of phytase (0, 125, 250, 500, 1,000, or 2,000 phytase units [FTU]/kg) with 0.4% of $TiO_2$ as a digestibility marker. Feeding schedule for each ingredient was 5 d acclimation, 5 d fecal collection, and 4 d washout. The STTD of P increased (linear or exponential $p{\leq}0.001$) with the inclusion of phytase for all ingredients. Results: Basal STTD of P was 37.6% for CM, 37.6% for corn, 68.6% for DDGS, 10.3% for RB, 41.2% for sorghum, 36.7% for SBM, 26.2% for SFM, and 55.1% for wheat. The efficiency of this novel phytase to hydrolyze phytate is best described with a broken-line model for corn, an exponential model for CM, RB, SBM, SFM, and wheat, and a linear model for DDGS and sorghum. Based on best-fit model the phytase dose (FTU/kg) needed for highest STTD of P (%), respectively, was 735 for 64.3% in CM, 550 for 69.4% in corn, 160 for 55.5% in SBM, 1,219 for 57.8% in SFM, and 881 for 64.0% in wheat, whereas a maximum response was not obtained for sorghum, DDGS and RB within the evaluated phytase range of 0 to 2,000 FTU/kg. These differences in the phytase concentration needed to maximize the STTD of P clearly indicate that the enzyme does not have the same hydrolysis efficiency among the evaluated ingredients. Conclusion: Variations in enzyme efficacy to release P from phytate in various feedstuffs need to be taken into consideration when determining the matrix value for phytase in a mixed diet, which likely depends on the type and inclusion concentration of ingredients used in mixed diets for pigs. The use of a fixed P matrix value across different diet types for a given phytase concentration is discouraged as it may result in inaccurate diet formulation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.6
• /
• pp.684-696
• /
• 1995

A mutant for chalky endosperm and genetic male sterility (GMS) was newly developed in rice. The two characters were found to be controlled by single recessive gene which has pleiotropic effect, indicating that chalky seeds should be GMS seeds in segregating populations. Chalky seeds showed the same shape and size as normal seeds. However, starch composition of central part of endosperm was looser and shape of starch granules was rounder compared with normal endosperm, resulting in significantly lower grain weight, absolute density and grain hardness in chalky grains than in normal ones. Amylose content and gel consistency of chalky grains were much lower and harder, respectively. Male sterile plants showed much shorter plant height, poorer panicle exsertion and lesser panicle number compared with normal plants. Microspore abortion stage in pollen developmental process was observed as before meiosis. Male sterility of the mutant was stable regadless of temperature and day length. A system breeding hybrid rice using this mutant was discussed, comp ring with other systems utilizing cytoplasmic-genic male sterility(CGMS) and environment sensitive GMS(EGMS). Separation of GMS seeds in mixed seed bulks by specific gravity (1.14∼1.16g / cm3) was successful about 85∼90%. But some mixed normal plants were seemed to be easily removed by the apparent difference in growth characters at seedling stage. The highest natural outcrossing rate of this GMS line was as 17.3 % in a plot treated with 2-row pollinator, I-row GMS, and GA3 + cutting of flag leaf + pollen-scattering by rope.

• Journal of Animal Science and Technology
• /
• v.47 no.5
• /
• pp.769-782
• /
• 2005

Twenty four Holstein steers fed commercial concentrates with rice straw(T1), mixed grass hay(T2), or wet brewer’s grains based TMR ad libitum(T3) were used to investigate the effects of roughage feeding type during the growing and early-fattening periods on growth performance, feed efficiency and carcass characteristics. Growth performance and feed efficiency were investigated during the feeding trial conducted from 6 to 23 mo of age, and carcass characteristics were investigated after slaughter. Body weight at slaughter and daily gains were 751 to 802 kg(mean 782 kg) and 1.064 to 1.159 kg/d(mean 1.122 kg/d), respectively, showing that those for T2 were highest followed by T3. Compared with T1, the daily gain for T2 was improved by 8.9%. The TDN intakes per kg gain were 6.87, 7.17 and 7.15 kg for T1, T3 and T2, respectively, indicating that feed efficiency for T2 was improved(approx. 5%) compared with T1. The feeding treatments did not change dressing percentage(mean 60.8%), back fat thickness(6.68 mm) and rib-eye area(84.0$cm^2$). Neither meat quality characteristics nor physicochemical properties were significantly different among the treatments. However, economic analysis accounting for 882.8, 991.7 and 943.8 thousand won per head for T1, T2 and T3, respectively, indicated that T2 and T3 increased(7-12%) total net income compared with T1. Therefore, it may be concluded that high quality meat of Holstein steers can be produced if they are fattened until 23 mo of age and that feeding mixed grass hay as roughage or TMR containing mainly wet brewer's grains during the growing and early-fattening periods can improve growth performance compared with feeding rice straw.