• 한국분말재료학회지
• /
• 제10권5호
• /
• pp.305-309
• /
• 2003

We report on the formation and chemical leaching of non-equilibrium $Al_{0.6}(Fe_{75}Co_{25})$ alloy produced by rod milling. X-ray diffractometry, transmission electron microscopy, differential scanning calorimetry, scanning electron microscopy, and vibrating sample magnetometry were used to characterize the as-milled and leached specimens. After 400 h, only the $Al_{0.4}Fe_{0.6}$ peak of the body-centered cubic type was present in the XRD pattern. The entire rod milling process could be divided into three different stages of milling: agglomeration, disintegration, and homogenization. The saturation magnetization, $M_s$ decreased with increased milling time, the $M_s$ of the powders before milling was about 113.8 emu/g, the $M_s$ after milling for 400 h was about 11.55 emu/g. Leaching of the Al in KOH of the Al at room temperature from the as-milled powders did not induce any significant change in the diffraction pattern. After the leached specimen had been annealed at $600^{\circ}C$ for 1 hour, the nanoscale crystalline phases were transformed into the bcc Fe, cubic Co, and $CoFe_2O_4$ phases. On cooling the specimen from 85$0^{\circ}C$, the degree of magnetization increased slightly, then increased sharply at approximately 364.8$^{\circ}C$, indicating that the bcc $Al_{0.4}Fe_{0.6}$ phase had been transformed to the Fe and Co phases.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1407-1410
• /
• 1997

Advanced sensor design and filtering technology have been studied to obtain information for condition monitoring and diagnostics inmachining processes. To develope and economic monitoring system in end milling processes, indirect and reliable type of cutting force estimators were required. In this paper, an estimation method of cutting forces during end milling processes was studied through the measurement of current signals obtained from spindle and feeddrive motors. Cutting force and torque models were derived from the cutting geometry in down milling processes. Relationships between motor currents and cutting forces were also developed in the form of AC and DC components from the developed force models. The validity of the cutting force estimator was confirmed by the experiments under various cutting conditions.

• 한국세라믹학회지
• /
• 제30권8호
• /
• pp.623-628
• /
• 1993

Lead monoxide has two phases at room temperature. One is a yellow orthorhombic phase, the other is a redtetragonal phase. Sometimes two phases are hybrided. The specificity of phase transitions of lead oxide is found during the milling of the batch including lead oxide. The pure orthorhombic phase of PbO can be transformed to the tetragonal phase perfectly by wet ball milling (milling liquid is distilled water) without thermal energy. However, when ethyl alcohol, isopropyl alcohol and aceton are used as milling liquid, respectively, the hybrid form of orthorhombic andtetragonal phases is obtained by wet ball milling. From the hybrid form heat-treated at $600^{\circ}C$ for 3hrs, this work results that mechanical phase transition of orthorhombic phase make a new form as distorted type orthorhombic phase of PbO.

• 한국작물학회지
• /
• 제39권1호
• /
• pp.63-72
• /
• 1994

보리의 이용성을 검토하기 위하여, 찰성 부정형 Shrunken endosperm 유전자를 결합하여 육성한 Isogenic line을 이용하여, 취반 및 제분에 대한 제특성을 조사한 바 그 결과를 요약하면 다음과 같다. 1. 보리의 배유 전분 특성이 다른 Isogenic type 간에 정곡 천립중, 회분, 단백질 함량은 별차이가 없었으나 Amylose함량, $\beta$-glucan viscosity와 취반특성은 뚜렷한 차이를 보였다. 2. 취반특성중 흡수율과 퍼짐성은 천립중, Amylose 함량과 부의 상관이 있었고, 용출고형물량과 점도간에도 부의 상관이 있었다. 3, 흡수율과 퍼짐성은 배유 전분 특성과 입의 크기에 의해 영향을 받았으며 그 결과 찰성 Isogenic type이 높았고 부정형 전분 Isogenic type이 가장 낮았으며 종실의 크기가 작은 것이 큰 것에 비해 높았다. 4. 보리밥의 Mixogram pattern은 전분 특성에 따라 차이가 있었으며 부정형 전분이 가장 많이 으깨어졌다. 5. 제분 특성은 메성이면서 부정형인 Isogenic type이 좋았고 찰성의 Shrunken endosperm Isogenic type은 대단히 불량하였다.

• Tribology and Lubricants
• /
• 제34권6호
• /
• pp.284-291
• /
• 2018

Ball-milling for reactant powders in advance and using an induction heating system for Ni-Al intermetallic coating process are known to enhance the reactivity of combustion synthesis. In this work, the effects of the charging weight ratio of ball to powder in ball-milling for reactant Ni-Al powders and the synthesizing temperature in induction heating on sliding wear behavior of the coating layers are investigated. Sliding wear behavior of the coating layers is examined against a tool steel using a pin-on-disc type sliding wear machine. As results, wear of the coating layer ball-milled without ball was severely worn out at the sliding speed of 2m/s, regardless of the synthesizing temperature in induction heating. However, the wear rate of the coating layers at the sliding speed was remarkably decreased with increasing the charging weight ratio of ball in ball-milling for reactant powders. This can be explained by the fact that the void in the coating layer is disappeared and the coating layer is densified by the ball-milling. The evidence showed that pitting damages were disappeared on the worn surface of ball-milled coating layer. Consequentially, the Ni-Al intermetallic coating layer could have better wear resistance at all sliding speed ranges with the ball-milling for reactant powders in advance.

• 한국염색가공학회지
• /
• 제4권2호
• /
• pp.76-83
• /
• 1992

Wool tropical and nylon taffeta were treated with low temperature plasma of $O_2$, $N_2$, NH$_3$, CF$_4$ and CH$_4$ for the intervals of 10 to 300 sec, and then dyed with leveling and milling type acid dyes in presence or absence of buffer solution. From the color depth of dyed fabrics, effect of plasma gases, treated time, dyeing time and temperature on dyeing property was studied. The results of the experiment can be summarized as follows: 1) The plasma treatments except methane gas increased the color depth of dyed wool fabrics, but not that of dyed nylon fabrics regardless of the plasma gases used. 2) The color depth of wool fabrics dyed in the dye bath without buffer solution was increased by the low temperature plasma, especially increased much more by CF$_4$ plasma treatment. It is found that with the identification of F- ion in the residual dye bath the hydrogen fluoride gas was adsorbed on wool fabrics in the plasma treatment. 3) The color depth of wool fabrics was increased with the time of $O_2$ and CF$_4$ plasma treatments. 4) In both cases of the leveling and milling type acid dyes, the rate of dyeing was increased in the low temperature plasma treatments, and it is found that the leveling type acid dye increased the color depth at relatively low temperature below 4$0^{\circ}C$, compared with the milling type acid dye.

• 한국염색가공학회지
• /
• 제1권1호
• /
• pp.47-53
• /
• 1989

The effect of organic solvent in the dyeing of silk fiber by acid dye was investigated. Acetophenone and benzyl alcohol were shown to be the most effective for the rate of dyeing of silk fiber by Milling Cyanine 5R (C.I. Acid Blue 113), a milling type acid dye, but, with benzyl alcohol, the equilibrium dye uptake was much lower than that in the absence of it. In the presence of solvent, maximum dye uptake shifted to lower temperature than 6$0^{\circ}C$, while without solvent, it was shown at about $60^\circ{C}$. When dyed by Orange II (C.I. acid Orange 7) under same condition equilibrium dye uptake of silk fiber was lower than that for milling type acid dye, and in the presence of benzyl alcohol, still much lower uptake resulted. All these fact reveals that organic solvents in the solvent-assisted dyeing of silk fiber broaden micelle spacings too much, resulting in increased rate of dyeing, and decreased equilibrium dye uptake, contrary to wool.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.717-720
• /
• 2000

Burr makes troubles on manufacturing process due to of deburring cost, quality of products and automation. This paper described the results of experimental study on the influence of the cutting parameters on the formation of exit burrs in face milling. Using the results of experimental study, we classified the burr type and developed data bases to predict burr formation result. This program will be used to predict burr type and geometry at a specified location. Simulation results on deformation strain and temperature are also available. Also algorithm which calculate the exit angle is proposed.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2664-2675
• /
• 1993

In this paper, the effects of chip breaker configuration on cutting forces for various cutting conditions are investigated and a method for predicting cutting forces effectively for chip breaker insert in milling is described. Based on the shear plane model and the relevant equations already existing for the relation among the parameters, the method makes use of the analytic geometric approach considering the configuration of cutting too by a 3-dimensional coordinate transformation matrix. The groove type chip breaker insert is modeled to be a double rake insert, represented by the first radial rake angle, the second radial rake angle and the length of land, and the program analyzing the cutting forces is developed. The program capability is verified by comparing the results with the experimental ones for a single cutter; and in case of primary cutting forces, the results of simulation and experiments agree very well showing 2%~16.7% difference within the feed rate range investigated.

• 한국분말재료학회지
• /
• 제17권4호
• /
• pp.302-311
• /
• 2010

In this research, the refinement behavior of the coarse magnesium powders fabricated by gas atomization was investigated as a function of milling time using a short duration high-energy ball milling equipment, which produces fine powders by means of an ultra high-energy within a short duration. The microstructure, hardness, and formability of the powders were investigated as a function of milling time using X-ray diffraction, scanning electron microscopy, Vickers micro-hardness tester and magnetic pulsed compaction. The particle morphology of Mg powders changed from spherical particles of feed metals to irregular oval particles, then platetype particles, with increasing milling time. Due to having HCP structure, deformation occurs due to the existence of the easily breakable C-axis perpendicular to the base, resulting in producing plate-type powders. With increasing milling time, the particle size increased until 5 minutes, then decreased gradually reaching a uniform size of about 50 micrometer after 20 minutes. The relative density of the initial power was 98% before milling, and mechanically milled powder was 92~94% with increase milling time (1~5 min) then it increased to 99% after milling for 20 minutes because of the change in particle shapes.