• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.218-218
• /
• 2008

최근 미관을 위하여 소형 네온관 등이 사용되고 있다. 따라서 네온관 등 구동에 사용되는 인버터는 안정기 역할을 하면서 소형화와 경량화가 중요한 요소이다. 본 연구는 압전 특성이 우수한 PZT계 세라믹스 조성인 $(Pb_{0.94}Sr_{0.06})[(Ni_{1/2}W_{1/2})_{0.02}(Mn_{1/3}Nb_{2/3})_{0.07}(Zr_{0.51}Ti_{0.49})_{0.91}]O_3$에 특성 향상을 위해 PbO, $Fe_2O_3$, $CeO_2$, Xwt% $Nb_2O_5$ 조성별로 첨가하였으며 그에 따른 유전, 압전 특성을 조사하고 또한 Rosen type의 압전 트랜스포머를 제작하여 각 조성별 변환효율을 측정하였다. 실험방법은 일반적인 세라믹스 제조공정으로 파우더 혼합 후 24시간 ball milling하고 $850^{\circ}C$ 에서 2시간 하소 후 $1230^{\circ}C$에서 2시간 소결하였다. 또한 최종 소결 시편을 이용하여 Rosen type의 압전 트랜스포머를 제작하였다. 상 분석을 위해 XRD를 이용하여 perovskite구조를 확인하고 미세구조확인을 위해 SEM으로 관찰하였다. 압전 특성을 평가하기 위해 압전 $d_{33}$ Meter를 사용하였으며, Impedence analyzer HP 4194A를 이용하여 전기적 특성을 측정하였다.

• Journal of Powder Materials
• /
• v.17 no.2
• /
• pp.136-141
• /
• 2010

Bismuth-telluride based $(Bi_{0.2}Sb_{0.8})_2Te_3$ thermoelectric powders were fabricated by two-step planetary milling process which produces bimodal size distribution ranging $400\;nm\;{\sim}\;2\;{\mu}m$. The powders were reduced in hydrogen atmosphere to minimize oxygen contents which cause degradation of thermoelectric performance by decreasing electrical conductivity. Oxygen contents were decreased from 0.48% to 0.25% by the reduction process. In this study, both the as-synthesized and the reduced powders were consolidated by the spark plasma sintering process at $350^{\circ}C$ for 10 min at the heating rate of $100^{\circ}C/min$ and then their thermoelectric properties were investigated. The sintered samples using the reduced p-type thermoelectric powders show 15% lower specific electrical resistivity ($0.8\;m{\Omega}{\cdot}cm$) than those of the as-synthesized powders while Seebeck coefficient and thermal conductivity do not change a lot. The results confirmed that ZT value of thermoelectric performance at room temperature was improved by 15% due to high electric conductivity caused by the controlled oxygen contents present at bismuth telluride materials.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.192-194
• /
• 2008

The study has focused on the dyeing properties of 4 kinds of high temperature type mono azo disperse dyes, widely used in the dyeing factory, under the ultra low liqour ratio (1:4) dyeing condition. Among those, C.I. Disperse Red 343 and C.I. Disperse Blue 79 showed un-levelled dyeing results from the ultra low liquor ratio dyeing bath as well as poor dispersion stability under the high temperature. We recommended some leveling agents to improve the leveling behavior of these dyes mentioned above. The milling technology should be further developed to achieve the dispersion stability.

• Korean Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.253-266
• /
• 1997

Pencil-curve machining, which is a single-pass ball-end milling along a concave edge on adie surface, is widely employed in die-surface machining. The cutter-path used for pencil-curve machining, which is the trajectory of the “ball-center point” of a ball-endmill sliding along a concave-edge region on the die surface, is called pencil-curve. Presented in the paper is a pencil-curve tracing algorithm in which “concave-type” sharp edges are computed from a “virtually digitized” model of the tool-envelope surface. The resulting “initial” pencil-cures are then refuted by applying a series of fairing operations. illustrative examples and methods for enhancing accuracy are also presented. The proposed pencil-curve tracing algorithm has been successfully implemented in a commercial CAM system specialized in die-machining and in the CAD/CAM system CATIA.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.27.2-27.2
• /
• 2009

Grinding characteristics for aluminium and carbon nanotubes (CNTs) powder during traditional and planetary ball milling investigated from the viewpoint of particle behaviour with the aimat developing CNT-dispersed samples ground based on powder metallurgy routes.In this work, a comparison between the pure aluminium and CNT input aluminium grinding was carried out to determine grinding time effect on size reduction.We observed that the use of the curly small-diameter multi-walled carbon nanotubes (MWCNTs) attributed to the beneficial role of the MWCNTs as grinding aids. It is suggested that careful choices of the sizes of CNTs and Al powders would allow fine-grinding of composite particles with uniformly distributed CNT reinforcements thereby ensuring improved properties of the final composites produced by low-temperature compacting.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.162-167
• /
• 2013

The most important factor in an aircraft manufacturing is stability and weight reduction. Most of aircraft components are designed with thin plate type to satisfy weight reduction needs. The thin plate is difficult to be machined because it is apt to be vibrated by dynamic force generated in milling process. The most critical factor in machining of aluminum thin plate is width and thickness between stiffeners. So we tested many cases to find out the machinable minimum thickness at different width between stiffeners. And with the data obtained from many tests, this papers suggested the standard width thickness relation that is machinable without vacuum fixture. Machinist will be able to reduce the cost of aircraft thin plate parts by reducing the number of vacuum fixture used by the help of this standard.

• Journal of the East Asian Society of Dietary Life
• /
• v.27 no.2
• /
• pp.194-203
• /
• 2017

Mealworm, a type of edible insect, is a superior food material suitable for industrial products. In this study, four different defatted mealworm powders were prepared to determine proper manufacturing conditions. Solvent extraction method reduced lipid contents of mealworms more than pressed mealworms, and lowered lipid contents caused bright colors and good physicochemical properties for powders. In comparison, differences among milling machines used for making powders were strongly related with average size of particles. Meanwhile, the predicted shelf-life of defatted mealworm powders judged by accelerated experiments was 1 year or longer. To enhance shelf-life of mealworm powders, addition of tocopherol to mealworm powders at a concentration of 0.2% could intensify oxidative stability and microbial inhibition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.371-374
• /
• 1997

This study presents a new type of real-t~me CNC interpolator that is capable of generating cutter paths for ball-end milling of NURBS surfaces. The proposed surface interpolator comprises real-time algorithms for cutter-contact (CC) path scheduling and CC path interpolation. Especially, in this study, a new interpolator module to regulate cutting forces is developed. This proposed algorithm utilizes variable-feedrate commands according to the curvature of machined surfaces. The proposed interpolator is evaluated and compared with the conventional method based on constant feedrates through computer simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1772-1775
• /
• 2003

The stiffness of multi-articulated industrial robots is very weak, because their structure is an articulated type with some links and joints. Thus it is known that cutting processes for metals are not accepted in machine shop well, but they have a lot of merits for cutting processes, for example. drilling, tapping. and engraving etc., because of the characteristics of their high degree of freedom. The temptation of cutting aluminium was carried out to investigate the feasibility and the limitations or constrains for cutting metals on them. First the mode shapes of 6-axes FANUC welding robot were taken and analysed, and next the cutting processes were practically carried out on it. The results of study were found out to show the feasibility of cutting processes at end-milling under 6mm of tool diameter. as well as to have some limitations and constrains, for examples, surface roughness and feed rate, depth of cut, cutting force etc..

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.47-51
• /
• 1992

Automatic detection of tool breakage during NC machining is a key issue not only for improving productivity but to implement the unattended manufacturing system. In this paper, we develop a vibration sensor-based tool breakage detection system for NC milling processes. The system obtains the time-domain vibration signal from the sensor attached on the spindle bracket of our CNC machine and declares tool failures through the on-line monitoring schemes. For on-line detection, our approach is to use the PSC(statistical process control) methods being increasingly used for on-line process control. The main thrust of this paper is to propose and compare the performance of SPC methods including : a) X-bar control scheme, b) S control scheme, c)EWMA (exponentially weighted moving average) scheme, and d) AEWMA (adaptive exponentially weighted moving average) scheme. The performance of the control schemes are compared in terms of the type 1 and 2 error calculated from the experiment data.