• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1749-1753
• /
• 2003

We proposed several systems for 1Giga bit Modem. The first, Binary ASK(Amplitude Shift Keying) system has a high speed shutter transmitter and no IF(Intermediate Frequency) receiver only by symbol synchronization. The advantage of proposed system is that circuitry is very simple without IF process. The disadvantage of proposed system are that line spectrum occurs interference to other channels, and enhancement to 4-level system is impossible due to its large SNR degradation. The second, Binary phase modulation system has a high speed shutter transmitter and IF-VCO(IF-Voltage Controlled Oscillator) control by base-band phase rotation. Polarity of shutter window is changed by the binary data. The window should be narrow same as above ASK. The advantage of proposed system is which error rate performance is superior. The disadvantage of proposed system are that Circuitry is more complex, narrow pull-in range of receiver caused by VCO and spectrum divergence by the non-linear amplifier. The third, 4-QAM(Quadrature Amplitude Modulation)system has a nyquist pulse transmitter and IF-VCO control by symbol clock. The advantage of proposed system are that signal frequency band is a half of 1GHz, reliable pull-in of VCO and possibility of double speed transmission(2Gbps) by keeping 1GHz frequency-band. The disadvantage of proposed system are that circuit complexity of pulse shaping and spectrum divergence by the non-linear amplifier.

• Journal of Communications and Networks
• /
• v.15 no.5
• /
• pp.476-485
• /
• 2013

In this paper, the effective capacity of a multiple-input multiple-output (MIMO) system in two different cases with receive antenna selection (RAS) and transmit antenna selection (TAS) schemes is investigated. A closed-form solution for the maximum constant arrival rate of this network with statistical delay quality of service (QoS) constraint is extracted in the quasi-static fading channel. This study is conducted in two different cases.When channel state information (CSI) is not available at the MIMO transmitter, implementation of TAS is difficult. Therefore, RAS scheme is employed and one antenna with the maximum instantaneous signal to noise ratio is chosen at the receiver. On the other hand, when CSI is available at the transmitter, TAS scheme is executed. In this case, one antenna is selected at the transmitter. Moreover, an optimal power-control policy is applied to the selected antenna and the effective capacity of the MIMO system is derived. Finally, this optimal power adaptation and the effective capacity are investigated in two asymptotic cases with the loose and strict QoS requirements. In particular, we show that in the TAS scheme with the loose QoS restriction, the effective capacity converges to the ergodic capacity. Then, an exact closed-form solution is obtained for the ergodic capacity of the channel here.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.3-12
• /
• 2016

Recently, the study on 5G mobile communication systems using the millimeter-wave frequency band have been actively promoted and the importance of compensation of the nonlinearity of power amplifier caused by the characteristics of millimeter-wave frequency propagation attenuation is increasing. In the paper, we propose a piecewise polynomial model based on subdivision coefficient which are characteristics of power amplifier separated linear section and a non-linear section. In addition, the structure of digital predistortion based on the proposed model and direct learning method are proposed to implement a digital predistortion. To verify the proposed model, digital predistortion based on the proposed model and direct learning method for 60 GHz power amplifier using LTE signal implemented in the FPGA. And the hardware test bench measured performance and complexity. The proposed model achieves 3.3 dB gain over the single polynomial model in terms of the ACLR and reduces 7.5 percent in terms of the complexity.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.2C
• /
• pp.181-187
• /
• 2012

Millimeter wave (MMW) readily penetrates fabrics, thus it can be used to detect objects concealed under clothing. A passive MMW imaging system can operate as a stand-off type sensor that scans people in both indoors and outdoors. However, because of the diffraction limit and low signal level, the imaging system often suffers from low image quality. Therefore, suitable statistical analysis and computational processing would be required for automatic analysis of the images. In this paper, a real-time concealed object detection is addressed by means of the multi-level segmentation. The histogram of the image is modeled with a Gaussian mixture distribution, and hidden object areas are segmented by a multi-level scheme involving $k$-means, the expectation-maximization algorithm, and a decision rule. The complete algorithm has been implemented in C++ environments on a standard computer for a real-time process. Experimental and simulation results confirm that the implemented system can achieve the real-time detection of concealed objects.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.73-80
• /
• 2004

In this paper, the implementation and embedding method of the existing air-filled waveguide-filters at millimeter-wave on general PCB substrate is introduced by systematically inserting the vias inside waveguide and mathematically manipulating the simple equations obtained ken the classical circular-post waveguide filter design. All the metal structures placed vertically such as side wall fur perfect ground plane and circular-post for signal control in the air-filled WR-22 waveguide are replaced with several types of via for constructing the bandpass-filter. Side wall and poles inside waveguide are realized by placing a series array of via and tuning the via diameter. The lengths of x, y, z axis are reduced in proportion to root square of employed substrate dielectric constant and especially the length of z axis can be more reduced due to the characteristics of the wave propagation. Because the mass production on PCB is possible without fabricating a large-scaled metal waveguide of WR-22 as input/output ports at millimeter-wave regime, the manufacturing cost is reduced considerably. Finally, when using multilayer process like LTCC for small-sized module, it is one of advantages to use only one layer f3r the filter fabrication. To evaluate the validity of this novel technique, order-3 Chebyshev BPF(Bandpass-Filter) centered at 40 GHz-band with a 2.5 ％ FBW (Fractional Bandwidth) were used. The employed substrate has relative dielectric constant of 2.2 and thickness of 10 mil of Rogers RT/Duroid 5880. Accroding to design and measurement results, a good performance of insertion loss of 2 ㏈ and return loss of -30 ㏈ is achieved at full input/output ports.

• Current Optics and Photonics
• /
• v.5 no.4
• /
• pp.466-476
• /
• 2021

Frequency-multiplication technology based on microwave photonic principles can be used to generate microwave and millimeter wave signals with a wide frequency tuning range. However, the existing cascaded external modulation frequency-tupling scheme needs to ensure the phase coherence of the modulated Radio Frequency (RF) signal, while the phase modulation directly limits the frequency tuning range of the external modulation frequency multiplication. In this paper, a novel approach for generating an incoherent frequency 12-tupling signal with cascade modulation is proposed. The structure of cascaded dual-parallel Mach-Zehnder modulators can generate a frequency 12-tupling signal. The proposed structure uses no filter or phase control of the RF driving signal. Microwave photonic frequency-tupling was realized under incoherent conditions. Software simulations and experiments validated the proposed structure and proved that it can generate frequency 12-tupling microwave signals under incoherent conditions. Both the frequency range and reliability of the frequency-tupling system has been improved by the proposed structure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.12
• /
• pp.1327-1337
• /
• 2014

In cellular communication systems employing millimeter wave (mmWave) bands for a link, a large amount of training time and network resources will be required to find a serving BS with the best transmit and receive (Tx-Rx) beam pair if downlink control signals are used. In this paper, a tracking technique for OFDM-based cellular communication systems with a mmWave link, where an analog beamforer is used at the mobile station (MS) and a digital beamformer is used at the BS, is proposed using an uplink signal. A technique to select a serving BS with the best beam pair is described using the uplink preamble sequence based on Zadoff-Chu sequence and a metrics which can be used to identify parameters such as beam ID (BID), MS ID (MID), and direction-of-arrival (DoA). The effectiveness of the proposed technique is verified via simulation with the spatial channel model (SCM) for a moving MS in mmWave cellular systems.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1763-1766
• /
• 2003

Millimeter-wave networking is composed of narrow beam link. it is very substantial that beam connecting point to point is fixed in right direction. It is major requirement in the beam network to keep the beam in best direction. In this paper, We propose the method to find a best suited direction of the antenna's beam using the Genetic Algorithm (GA) in point-to-point link. Proposed method presume that each station knows his direction ${\theta}_1$ , ${\theta}_2$ at every step of GA, then it can be expected that GA is possible to search the ideal solution. Intensity of the received signal is evaluated by the multiplication of lengths to the point which the lobe meets with the horizontal line.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.243-244
• /
• 2022

In this paper, experiments were conducted on signal amplification of polymer capsules for application to Ground Penetrating Radar so as to enable real-time monitoring of polymer capsules inside concrete using the Morphology Dependent Resonance phenomenon. A TEM CELL and a vector network analyzer were used to analyze the difference in resonance frequency depending on the material of the sphere and the presence or absence of fracture. In order to manufacture a capsule of a size that can be measured using millimeter waves used in GPR, we manufactured a capsule with a 3D printer and analyzed the effects of the presence or absence of coating and the size of the capsule on the resonance frequency. Resonant frequency or signal amplification is more affected by diameter than coating. The capsule showing the highest amplification is the resin-coated 50 mm diameter capsule with a 316-fold increase and the lowest capsule is the uncoated 10 mm diameter capsule with a signal amplification of 11.9 times. These results demonstrate the potential of GPR to measure the position and state of self-healing capsules, which are small-sized polymers, in real time using millimeter waves.

• Current Optics and Photonics
• /
• v.2 no.4
• /
• pp.308-314
• /
• 2018

Visible light communication (VLC) is considered a strong future candidate for indoor wireless communication. However, its performance seems to be relatively unsatisfactory when compared to wireless local area network (WLAN) communication using millimeter waves. To improve the performance of VLC, numerous technologies have been proposed so far, in both electrical and optical domains. Among the proposals, optical beamforming (OB) is an optical-domain technology that can concentrate light in a specific direction or on a target spot. It can significantly improve VLC performance and can be widely used, because it does not depend on electrical modulation schemes. Therefore, this review discusses the concept, principle, and types of OB, the structure of a VLC system using OB, performance results of OB, and the combination of OB with electrical signal modulation in VLC. OB is expected to be one of the key techniques in future VLC implementations, similar to radio-frequency beamforming in millimeter-wave communication.