• Journal of Soil and Groundwater Environment
• /
• v.13 no.6
• /
• pp.23-30
• /
• 2008

Air sparging technique has been used for remediation of VOC(volatile organic compound)-contaminated aquifer. The aim of this study was to develop an innovative air sparging technique that enhances the efficiency of air intrusion into a specific horizontal layer of aquifer where the contaminants exist with the help of water-soluble surfactant. A twodimensional physical box model, packed with homogeneous sand, was used for simulating the aquifer in this study. Aqueous solution of anionic surfactant (100 mg/L, sodium dodecylbenzene sulfonate) was used to suppress the surface tension of groundwater. Three sets of experiments were conducted: air sparging experiment without surfactant application, air sparging experiments for box model where the surfactant solution was applied right above the air injection point, and air sparging experiments with surfactant solution layer formed in the middle of the box. It was found that the sparging influence zone was expanded up to five times of that formed by sparging without surfactant application. The size of sparging influence zone was more sensitive to the air flow (injection) rate with surfactant application than that without surfactant. More importantly, injection of air into the target aquifer layer was successful with surfactant application. Findings in this study are expected to provide more options for designing remediation processes using air sparging.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.6
• /
• pp.53-62
• /
• 2013

A 5-20 cm thick shocrete has been routinely constructed for NATM tunneling method to stabilize and confine the excavated rock of tunnel construction site. A $40kg/m^3$ of steel fibers are usually mixed into such shotcrete but these steel fibers may not be evenly distributed depending on shotcrete machines, mixing ratios and excavated rock conditions. In this study, square column shotcrete-mimicked concrete specimens of $15cm{\times}15cm{\times}55cm$ were prepared with 5 equal layers and 5 or 20% cement ratio. The specimens were prepared with different reinforced-patterns: non-reinforced, middle layer-reinforced, 1, 3, and 5 layers-reinforced, or all layers reinforced. The specimens were air-cured for 7 days and tested for flexural strength. The influence of steel-fiber distribution on flexural strength and toughness of shotcrete-mimicked concrete specimens was investigated. In the case of a specimen with cement ratio of 20%, a flexural strength increased as a number of fiber-reinforced layer increased. The flexural strength of one-layer reinforced specimen showed 20% less than that of evenly fiber-distributed specimen. On the other hand, a specimen with cement ratio of 5% decreased as the number of fiber-reinforced layers increased. A toughness index increased as the number of fiber-reinforced layers increased, regardless of cement ratios. The toughness index of evenly fiber-distributed specimen showed 2-3 times as large as that of one-layer reinforced specimen.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.115-121
• /
• 2015

In this paper, we proposed an iterative data-flow optimal scheduling algorithm based on genetic algorithm for high-performance multiprocessor. The basic hardware model can be extended to include detailed features of the multiprocessor architecture. This is illustrated by implementing a hardware model that requires routing the data transfers over a communication network with a limited capacity. The scheduling method consists of three layers. In the top layer a genetic algorithm takes care of the optimization. It generates different permutations of operations, that are passed on to the middle layer. The global scheduling makes the main scheduling decisions based on a permutation of operations. Details of the hardware model are not considered in this layer. This is done in the bottom layer by the black-box scheduling. It completes the scheduling of an operation and ensures that the detailed hardware model is obeyed. Both scheduling method can insert cycles in the schedule to ensure that a valid schedule is always found quickly. In order to test the performance of the scheduling method, the results of benchmark of the five filters show that the scheduling method is able to find good quality schedules in reasonable time.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.4
• /
• pp.124-131
• /
• 2009

A reliable detection of regions in radiography is one of the most important task before the evaluation of defects on welded joints. The extracted features is to be classified into distinctive clusters for each segmented region. But conventional segmentation techniques give unsatisfactory results for this task due to the spatial superposition of intensity and low signal-to-ratio(SNR) in radiographic images. The usage of global or local processes not only provide the necessary noise resistance but also fail in classification of regions. In this paper, we presents an appropriate approach for segmentation of region-based indications in industrial Computed Radiography(CR) images. The geometric differences between welded and non-welded area which is generated on radiography as the representative regions(background, thickness, middle and welded region in steel tube image) have constructed the hierarchical structure. Although this structure is contaminated by noise, the scheme between regions can be selected by the help of local clustering based on distinctive geometric property of each region. Because of the geometric nature of the considered region and so that the region is selected layer by layer, and that the real class represents the boundary between regions, the vertical and horizontal clustering process in each layer must be judicious. In order to show the effectiveness of this approach, a comparative experiment of various segmentation method is performed on industrial steel tube CR images.

• Korean Journal of Environment and Ecology
• /
• v.15 no.4
• /
• pp.379-393
• /
• 2002

Thirty-six plots (each size 100m2) have been set up and surveyed to investigate the plant community structure and the ecological density of Pinus densiflora for. eracta(Chunyang-type) community in Seobyeok-ri, Chungyang-myeon, bonghwa-gun, Kyeongsangbuk-do. Four communities, Community I (large DBH class), Community II (large DBH class), Community III (middle DBH class), Community IV(small DBH class), were classified into by mean DBH and mean height. Pinus densiflora for. eracta dominate in canopy layer, Fraxinus sieboldiana and Quercus mongolica dominate in understory layer, Rhododendron Schlippenbachii and R. mucronulatum dominate in shrub layer. It turned out that thefour communiteis had low species diversity(0.4320~0.9487; unit: 400$m^2$) and high similarity. By the result of ecological density analysis. the mean basal area was proportionated to mean DBH (cm) size. By the result of simple regression analysis between mean DBH(cm), mean distance(m), and the number of individual were as follow: Ecological distance(m) = 0.0934$\times$ DBH(cm) +0.6117, Number of individual=242.47$\times$ DBH(cm)$^{-1.009}$, Ecological distance=9.643$\times$No. of individua $l^{-0.7016}$. In addition to four communities were suitable to the growth of Tricholoma matsutake because average species were about 30~50 years old, litter layer was 0.5~2.5cm and the ratio of coverage shrub was 20% .

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.4
• /
• pp.41-48
• /
• 1986

This study was fulfilled by the weighing lysimeter method at the experimental farm of KonKuk University from April to June of 1986 to investgate the amount of evapotranspiration ( ET-lettuec )by the growing periods, evapotranspiration ratio, amount of watering per one time, days of intermission and soil moisture extraction pattern of the crisphead lettuce cultivated in the clay loam soil by different watering points of pFl.7, pF2.O, pF2.7. The results obtained are summar ized as follows : 1.The total evapotranspiration(ETlettuce) of the pFl.7 treatment plot was 358,9mm., 314.9mm in the pF2.O plot and 281.8mm in the pF2.7 plot, therefore the total ETlettuec increased with the difference of 33mm-44mm by the decrease of watering point. 2.The daily maximum ETlettuce by the watering points was 7.66mm, 6:54mm, 5.98mm, respectively in the last ten days of May, and the mean daily ETlettuce during the growing season by the watering points of pFl.7, pF2.O and pF2.7 was 5.44mm(384.5g), 4.77mm(337.2g) and 4.27mm(301.8g), respectively. 3.The evapotranspiration ratio showed maximum value in the middle of May which was the beginning of mid-season stage, and the mean evapotranspiration ratio during the total growing period was 1A7, 1.29, 1.15 by the watering points. 4.The days of watering intermission by the watering points of pFl.7, pF2.O and pF2.7 was 1.0day, 2.9days and 12.Sdays, respectively. 5.The yield of the crisphead lettuce by the watering treatments showed very high significance, and the pF2.O was confirmed as a optimum watering point. 6.The soil moisture extraction pattern(SMEP) of the pF2.0 treatment plot in the initial stage was 85.6% in the 1st and 2nd soil layer and 14.4% in the 3rd and 4th layer, and in the midseason stage, the moisture extraction proportion of the under layer accounted for 34.7%which showed that the root elongated to the lowest soil layer, and there was no difference of the SMEP between the mid-season and late-season stage. 7.The correlation coefficient between the ETlettuce and yield of lettuce by the three watering points was.739, which showed the significance of 5%.

• Korean Journal of Materials Research
• /
• v.10 no.10
• /
• pp.684-690
• /
• 2000

In order to study effects of interfacial layers between $Pb(Zr,Til)Q_3(PZT)$ films and electrodes for Metal-Ferroelectric-MetaI(MFM) structure capacitors, we have fabricated the capacitors with the Pt/PZT/interfacial-layer/Pt/$TiO_2/SiO_2$/Si structure. $PbTiO_3(PT)$ interfacial layers were formed by sol-gel deposition and PbO, ZrO, and $TiO_2$ thin layers were deposited by reactive sputtering. $TiO_2$ interface layers result in the finest grains of PZT(crystalline Temp. $600^{\circ}C$) films compare to $PbO_2\;and\;ZrO_2$ layers. However, as the thickness of $TiO_2$ layer increases. PZT thin films become rough and electrical characteristics were deteriorated due to remained anatase phase. On the other hand. PT interface layers result in improved morphology of PZT films and do not significantly change ferroelectric properties. It is a also observed that seed layers at the middle and top of PZT films do not give significant effects on grain size but the PT seed layer at the interface between the bottom electrode and the PZT films results in the small grain size.

• Journal of Korean Medical classics
• /
• v.22 no.1
• /
• pp.121-130
• /
• 2009

Traditionally, Korean Medicine put emphasis on the treatment and health-preserve method that corresponds with circulation of nature. And acupuncture is no exception to this rule. In "Hwangjenaegyeong(黃帝內經)", some chapters present method that is changed according to the seasons. Among the chapters, there are some difference, but we can find a general theory. In spring, Yanggi(陽氣) is coming out but not strong and cannot diffuse. so the Yanggi(陽氣) hang up the middle of outer layer. Therefore, we can take some acupoints around the muscle interspace[分腠] or tiny branches of Meridian[孫絡]. In summer, Yanggi(陽氣) flourish and boil all around of the outer layer. So, we can take some acupunctural points from skin to the yang-meridian. In both fall and winter, five su point[五輸穴] make up almost of point. in fall, yanggi begin convergence. we can remove the Eum-pathogen[陰邪] and help the normal convergence by using Stream point[腧穴], River point[經穴] and Sea point[合穴]. In winter, Eum surround so solidly that the neo Yanggi(陽氣) cannot come out. So, we can break the yin by using Well point[井穴] and make be strong by Spring point[滎穴]. If we Study the method that correspond with the seasonal circulation more, we will be able to treat diseases more minutely.

• Journal of Forest and Environmental Science
• /
• v.14 no.1
• /
• pp.89-100
• /
• 1998

The study was carried to investigate the change of internal stress and physical properties of paper by the mutiplying of paper structuring that is an useful means to maximize the performance and use of the fiber raw material. The effects of recycled fiber on the physical properties of multiplied paper also were studied. The beating increased the internal stress of single layered paper, while filler loading decreased the internal stress. Multiplying the structure of paper decreased the internal stress and the most of physical properties except for tear index. It was found that the properties of paper could be changed by the pulp type, beating and the combination of raw materials. The introduction of filler in the middle and/or outer layer could improved the internal stress, tensile index, tear index and burst index. The addition of recycled fiber increased the opacity and stiffness of paper in both single layered and multiplied paper. Multiplying the structure of paper improved the air permeability and stiffness, while decreased burst index.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.4
• /
• pp.38-45
• /
• 2015

Fold cracking is one of quality troubles of coated papers. In this study, the fold cracking of high grammage ($250g/m^2$) coated paper made with the different pulp composition and layer structure of base paper was investigated. The single layered, high grammage base paper was prepared by mixing of hardwood and softwood bleached kraft pulp fibers with the different ratios. The high grammage coated paper showed the higher fold cracking than low grammage coated paper because of the increase in thickness. The increase in the content of softwood pulp fibers reduced the fold cracking in the case of high grammage coated paper. When the creasing process was conducted before folding process, the fold cracking of coated paper decreased. By manufacturing the base paper with multiply structure, the fold cracking of coated paper could be reduced significantly, especially when the BCTMP and OCC were used as a middle layer and the creasing process was carried out. The delamination of layers in base paper affected the fold cracking positively.