• Elastomers and Composites
• /
• v.41 no.3
• /
• pp.164-171
• /
• 2006

Stress softening behaviors of SBR vulcanizates reinforced with silica or carbon black were studied. Two types of SBR with different 1,2-unit contents of 18 and 60 wt% were used and three filler systems of carbon black and silica with/without silane coupling agent were employed. Stress softening behaviors of the SBR vulcanizates were varied with the SBR types as well as the filler systems. The silica-filled rubber specimens had higher residual strains than the carbon black-filled ones. The residual strains of silica-filled vulcanizates were remarkably reduced by adding a silane coupling agent. The maximum loads at 50% maximum stretch of the carbon black-filled vulcanizates were lower than those of the silica-filled ones. On the contrary, the maximum loads at 200% maximum stretch of the carbon black-filled vulcanizates were higher than those of the silica-filled ones. The maximum loads of the specimens with the 1,2-unit content of 60 wt% are higher than those with the 1,2-unit content of 18 wt% irrespective of the filler systems.

• Journal of Ginseng Research
• /
• v.19 no.1
• /
• pp.62-72
• /
• 1995

During the controlled atmosphere storage (CA), fresh ginseng showed good appearance in quality, and other deterioration of freshness was not observed until 12 weeks. On the other hand, MA storage had kept freshness only in treatment of 1 until 8 weeks. There was no significant difference between treated and non-treated sample with preservatives, and not treated sample was not infected with various different fungi. Moisture contents and hardness of ginseng in all treatments were not changed much until 12 weeks, and surface shrinkage did not occur either. But shear stress increased somewhat in all treatments after 12 weeks. The granule of microstructure in tissue diminished slightly. The apparent Quality of red ginseng was good until 4 weeks of treatment. But as time passed, white skin and wrinkled skin were generated and darkened in its color. B-1 in CA and E-1 in MA were found to be the most favorable one. The content of crude saponin did not change significantly during storage of CA or MA by preservation conditions and period. Though a small increase in saponin content from 4.92% to 5.43% was recognized in B-1, which was treated with preservative and 6.0% In B-2, control, this could rather explain increment of soluble component by butanol. Thus, there was no change in total contents of ginsenoside pattern and composition of each content. The Rbl content in B-1 and B-2 were 0.98%, and 0.97%, respectively, whereas that of control was 0.96%. E-1 of MA, treated with preservative was 5.32% after 12 weeks, but was 5.73% in control, indicating that ginsenosides pattern was quite similar to that of CA storage.

• Korean Journal of Food Science and Technology
• /
• v.41 no.4
• /
• pp.369-373
• /
• 2009

${\alpha}$-Waxy corn starch was used as a feed for twin-screw extrusion in order to enhance starch liquefaction with added thermostable ${\alpha}$-amylase (derived from Bacillus licheniformis). The residence time distribution and starch liquefaction were investigated. The starch liquefaction was analyzed in terms of reducing sugar contents, molecular size from gel permeation chromatography (GPC), and microstructure from scanning electron microscopy (SEM). The use of ${\alpha}$-starch contributed to the production of more reducing sugar than the use of raw starch use alone. From GPC, the effect of ${\alpha}$- starch on the molecular size reduction was shown to be small. From SEM, irregular and damaged surface were observed on the extrudate from ${\alpha}$-starch, as compared to those from raw starch. The spread of residence time distribution curves was greater with feed of ${\alpha}$-starch than raw starch, indicating that ${\alpha}$-starch was hard to flow forward during extrusion. This could be improved by increasing the feed moisture content and barrel temperature of extruder.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.368-372
• /
• 2011

Aluminum nitride (AlN) has excellent thermal conductivity, whereas it has some disadvantage such as low sinterability. In this study, the effects of sintering additive content and sintering condition on thermal conductivity of pressureless sintered AlN ceramics were examined on the variables of 1~3 wt% sintering additive ($Y_2O_3$) content at $1900^{\circ}C$ in $N_2$ atmosphere with holding time of 2~10 h. All AlN specimens showed higher thermal conductivity as the $Y_2O_3$ content and holding time increase. The formation of secondary phases (yttrium aluminates) by reaction of $Y_2O_3$ and $Al_2O_3$ from AlN surface promoted the thermal conductivity of AlN specimens, because the secondary phases could reduce the oxygen contents in AlN lattice. Also, thermal conductivity was increased by long sintering time because of the uniform distribution and the elimination of the secondary phases at the grain boundary by the evaporation effect during long holding time. A carbothermal reduction reaction was also affected on the thermal conductivity. The thermal conductivity of AlN specimens sintered at $1900^{\circ}C$ for 10 h showed 130~200W/mK according to the content of sintering additive.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.529-534
• /
• 2016

Nanocrystalline powder of zirconia stabilized with 8 mol% yttria (YSZ) has been synthesized through oxalate process using $ZrOCl_2{\cdot}8H_2O$ and $Y(NO_3)_3{\cdot}6H_2O$ as starting materials. Understanding of the characteristic changes of YSZ powder as a function of processing conditions is crucial in developing dense and porous microstructures required for fuel cell applications. In this research, microstructure change, surface area, particle shape and particle size were measured as a function of different processing conditions such as calcination temperature, stirring speed and concentration of starting materials. The resultant crystallite sizes were calculated by XRD-LB (X-Ray Diffraction Line-Broadening) method, BET method, and morphology of the crystal was observed in TEM and FE-SEM. The TEM examination showed that the powder synthesized with 0.7 M of YSZ concentration had a spherical morphology with sizes ranging from 20 to 40 nm. However, the powder was gradually aggregated above 1.0 M of YSZ concentration with the aggregation being intensified as the YSZ concentration was increased.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.3
• /
• pp.638-642
• /
• 2014

In this study, we investigate on the crystal microstructure and magneto-resistance (MR) change of Bismuth(Bi) thin films for annealing process, in order to apply Bi thin films to the spin electronic devices. As-prepared Bi thin films show the randomly oriented find grains whose size was measured to about 100 nm and the very low MR (4.7 % at room temperature) while careful annealing results in not only grain growth up to ${\sim}2{\mu}m$ but also drastic MR improvement (404 % at room temperature). The drastic change in the MR after applying the annealing process is attributed to the grain growth decreasing grain boundary scattering of electron. Therefore, in this study, we confirm the annealing effect for the grain boundary formation and MR improvement of Bi thin films, and demonstrate the feasibility of spin electronic devices.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.391-395
• /
• 2005

This paper has comparatively analyzed the characteristics of the machined surface of a specimen made by machining Die Steel STD11 and a specimen obtained by W-EDM steel. If a press die is manufactured through W-EDM, products of shapes that cannot easily be made through machining can be manufactured easily. However, the life of the press die is significantly reduced compared with the press die made through machining. This is believed to be caused by the deformed layer that has occurred on the surface of the press die that was made through W-EDM. The roughness of the 2 specimens was measured, and it was learned that the distribution of the roughness of the specimen made through the 1st W-EDM was rough. When the specimens were observed using a scanning-electron microscope, there was significant difference between the surface and the cross-section of the 2 specimens, while the cross section of the specimen obtained through W-EDM had the tempered and quenched surface structure which exists in the form of a deformed layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.10
• /
• pp.652-657
• /
• 2015

We have investigated the properties of Al-doped ZnO (AZO) thin films as functions of atomic layer deposition (ALD) oxidants. AZO transparent conducting oxides (TCOs) layer was deposited by ALD with adding trimethylaluminum (TMA) and diethylzinc (DEZn). AZO films were deposited at low temperature with $H_2O$ and $O_3$ as oxidants. Electrical, optical and structural properties of AZO thin films were investigated by 4-point probe, Hall effect measurement, UV-VIS, and AFM. Microstructure and atomic bonding states were investigated by HRXRD and XPS. The resistivity of AZO films grown using $H_2O$ was lower than the films grown using $H_2O$ and $O_3$, by approximately two orders of magnitude. The differences in oxygen vacancy peak intensity of AZO films were correlated to the optical and electrical properties.

• Journal of Powder Materials
• /
• v.27 no.4
• /
• pp.325-332
• /
• 2020

In this study, the effects of kaolin addition on the properties of reticulated porous diatomite-kaolin composites are investigated. A reticulated porous diatomite-kaolin composite is prepared using the replica template method. The microstructure and pore characteristics of the reticulated porous diatomite-kaolin composites are analyzed by controlling the PPI value (45, 60, and 80 PPI) of the polyurethane foam (which are used as the polymer template), the ball-milling time (8 and 24 h), and the amount of kaolin (0-50 wt. %). The average pore size decreases as the amount of kaolin increases in the reticulated porous diatomite-kaolin composite. As the amount of kaolin increases, it can be determined that the amount of inter-connected pore channels is reduced because the plate-shaped kaolin particles connect the gaps between irregular diatomite particles. Consequently, a higher kaolin percentage affects the overall mechanical properties by improving the pore channel connectivity. The effect of kaolin addition on the basic properties of the reticulated porous diatomite-kaolin composite is further discussed with characterization data such as pore size distribution, scanning electron microscopy images, and compressive strength.

• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.130-134
• /
• 2015

The high efficiency cell research processes through the KF post deposition treatment (PDT) of the $Cu(In,Ga)Se_2(CIGS)$ thin film has been very actively progress. In this study, it CIGS thin film deposition process when KF PDT 300 to the processing temperature, 350, $400^{\circ}C$ changed to soda-lime glass (SLG) efficiency of the CIGS thin film characteristics, and solar cell according to Na presence of diffusion from the substrate the effects were analyzed. As a result, the lower the temperature of KF PDT and serves to interrupt the flow of current K-CIGS layer is not removed from the reaction surface, FF and photocurrent is decreased significantly. Blocking of the Na diffusion from the glass substrate is significantly increased while the optical voltage, photocurrent and FF is a low temperature (300, $350^{\circ}C$) in the greatly reduced, and in $400^{\circ}C$ tend to reduce fine. It is the presence of Na in CIGS thin film by electron-induced degradation of the microstructure of CIGS thin film is expected to have a significant impact on increasing the hole recombination rate a reaction layer is formed of the K elements in the CIGS thin film surface.