• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.1
• /
• pp.83-92
• /
• 2011

Evidence on the effect of $O_2$ reduction or current passage on the microstructure and morphology of the LSM and Ni-YSZ electrodes in solid oxide fuel cells. The microstructures of the electrodes were characterized as plate-like agglomerates. Current of $0.1\;A/cm^2$, $0.2\;A/cm^2$, $0.3\;A/cm^2$, at $800^{\circ}C$ were passed for 3 h. Then, we observed the cell structure and measured the cell performance before and after the experiment. There are changed with the load condition. The TPB of the cell increased when the cell structure changed. In particular, the decrease in activation loss is apparent as load increased. As a result, cell performance improved, and we confirmed that a optimal load condition existed.

• Journal of Sensor Science and Technology
• /
• v.15 no.3
• /
• pp.216-221
• /
• 2006

ZnO thin films prepared by PLD method exhibit an excellent optical property, but may have some problems such as incomplete surface roughness and crystallinity. In this study, undoped ZnO buffer layers were deposited on (0001) sapphire substrates by ultra high vacuum pulse laser deposition (UHV-PLD) and molecular beam epitaxy (MBE) methods, respectively. After post annealing of ZnO buffer layer, undoped ZnO thin films were deposited under different oxygen pressure ($35{\sim}350$ mtorr) conditions. The Arsenic-doped (1, 3 wt%) ZnO thin layers were deposited on the buffer layer of undoped ZnO by UHV-PLD method. The optical property of the ZnO thin films was analyzed by photoluminescence (PL) measurement. The ${\theta}-2{\theta}$ XRD analysis exhibited a strong (002)-peak, which indicates c-axis preferred orientation. Field emission-scanning electron microscope (FE-SEM) revealed that microstructures of the ZnO thin films were varied by oxygen partial pressure, Arsenic doping concentration, and deposition method of the undoped ZnO buffer layer. The denser and smoother films were obtained when employing MBE-buffer layer under lower oxygen partial pressure. It was also found that higher Arsenic concentration gave the enhanced growing of columnar structure of the ZnO thin films.

• Laser Solutions
• /
• v.16 no.3
• /
• pp.1-10
• /
• 2013

In this study, Al-Si coated boron steel(1.2 mm) were laser welded by $CO_2$ laser and hot-stamping was applied to the laser joints. Tensile properties and microstructures of the joints were investigated before and after hot-stamping. Tensile and yield strengths of the as welded specimen similar with base metal and fracture occurred base metal of boron steel. Although, in case of heat treated specimen, fracture occurred fusion zone that Al segregated zone near the bond line. These could be explained by the existence of ferrite, in the Al segregated zone near the bond line and base metal of boron steel. Before hot-stamping, hardness of base metal is lower than fusion zone and heat affected zone in spite of exist Al segregation zone($Fe_3$(Al,Si)). So fracture occurred base metal. Although, after hot-stamping, microstructure of base metal and welds zone transformed to martensite and bainite except in Al segregation zone near the bond line that $Fe_3$(Al,Si) transformed to a-ferrite. So fracture occurred Al segregation zone near the bond line.

• Journal of Animal Science and Technology
• /
• v.62 no.4
• /
• pp.577-586
• /
• 2020

This study was to investigate the effect of salt alone or in combination with phosphate on physicochemical and textural properties, and chemical interactions of low-fat model sausages. pH, color, expressible moisture (EM), cooking loss (CL), proximate analysis, textural profile analysis and low-vacuum scanning electron microscopy were performed. As salt content increased, color tended to decrease, as did EM and CL parameters, indicating that the ability to retain moisture was improved with increased salt levels (p < 0.05). In addition, textural hardness, gumminess and chewiness all increased with increasing salt (p < 0.05). Sausages with 0.3% salt showed the lowest cohesiveness compared to those with salt levels higher than 0.3% (p < 0.05). Addition of sodium tripolyphosphate (STPP) increased pH of sausages. Increasing salt and STPP did not affect lightness (p > 0.05), but did increase redness and yellowness (p < 0.05). The moisture content was higher when the salt and STPP contents were increased (p < 0.05), but no differences in the fat and protein contents (%) were observed (p > 0.05). EM and CL tended to decrease with increasing salt and STPP. In textural properties, the combination of 1.8% salt and 0.3% STPP was the best among other treatment (p < 0.05). Surface microstructure showed a flat and dense structure with increasing salt and STPP. Since the addition of salt and phosphate improved the functionality, textural and physicochemical properties of meat products in this study, meat products will need to be developed in line with consumer's preference.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.2
• /
• pp.114-125
• /
• 2002

As semi-solid forging (SSF) is compared with conventional easting such as gravity die-easting and squeeze casting, the product without inner defects can be obtained from semi-solid forming and globular microstructure as well. Generally speaking. SSF consists of reheating, forging, ejecting precesses. In the reheating process, the materials are heated up to the temperature between the solidus and liquidus line at which the materials exists in the form of liquid-solid mixture. The process variables such as reheating time, reheating temperature, reheating holding time, and induction heating power have much effect on the quality of the reheated billets. It is difficult to consider all the variables at the same time when predicting the quality. In this paper, Taguchi method, regression analysis and neural network were applied to analyze the relationship between processing conditions and solid fraction. A356 alloy was used for the present study, and the learning data were extracted by the reheating experiments. Results by neural network were on good agreement with those by experiment. Polynominal regression analysis was formulated by using the test data from neural network. Optimum processing condition was calculated to minimize the grain size, solid fraction standard deviation, otherwise, to maximize the specimen temperature average. In this time, discussion is liven about reheating process of row material and results are presented with regard to accurate process variables for proper solid fraction, specimen temperature and grain size.

• Transactions of Materials Processing
• /
• v.20 no.2
• /
• pp.140-145
• /
• 2011

The aim of the present study is to derive optimized post heat treatment temperatures to get a proper formability for Ti/STS409L/Ti clad materials. These clad materials were fabricated by cold rolling followed by a post heat treatment process for 10 minutes at temperatures ranging from $500^{\circ}C$ to $850^{\circ}C$. The microstructure of the interface was observed using a Scanning Electron Microscope(SEM) and an Energy Dispersive X-ray Analyser(EDX) in order to investigate the effects of post heat treatment on the bonding properties of the Ti/STS409L/Ti clad materials. Diffusion bonding was observed at the interfaces with a diffusion layer thickness increasing with the post heat treatment temperature. The diffusion layer was composed of a type of(${\varepsilon}+{\zeta}$) intermetallic compound containing additional elements, namely, Fe, Ti and Ni. The micro Knoop hardness of the Ti/STS409L interfaces was found to increase with heat treatment up to $800^{\circ}C$ and then decrease for temperatures rising up to $850^{\circ}C$. The tensile strength was shown to decrease for heat treatment temperature increasing to $750^{\circ}C$ and then increase rapidly for temperature rising up to $850^{\circ}C$. A post heat treatment temperature range of $700{\sim}750^{\circ}C$ was found to optimize the formability of Ti/STS409L/Ti clad materials.

• Journal of Welding and Joining
• /
• v.21 no.4
• /
• pp.46-55
• /
• 2003

TiO$_2$-WO$_3$(8.2wt%) coatings were prepared by the APS (Atmospheric Plasma Spraying) process to clarify the relationship between the process parameters(H$_2$ gas flow rate of plasma 2nd gas and spraying distance) of the APS coating and photo-decomposition efficiency kinetics of the MB(methylene blue) aqueous solution decomposition and to understand the effect of addition of WO$_3$ on photocatalytic properties of TiO$_2$ sprayed coating. Further, the temperature and velocity of flying particles were measured by DPV-2000 to investigate the relationship between microstructure of coatings and process parameters. Properties of coatins were investigated by XRD, SEM, XPS, RAMAN, UV/VIS spectrometer. In case of the TiO$_2$-WO$_3$(8.2wt%) coating, it had a lower anatase fraction than that of pure-TiO$_2$ coatings because of flying in the higher temperature plasma plume by the heavy weight of TiO$_2$, WO$_3$. And, when WO$_3$ added powders were spayed, the doping effects of W ions substituted into the Ti ion sites was not occured during melting and solidification cycles of spraying. It was found that the addition of WO$_3$ was ineffective effective on increasing photo-decomposition efficiency of TiO$_2$ sprayed coating.

• Journal of Welding and Joining
• /
• v.33 no.2
• /
• pp.8-13
• /
• 2015

This study was carried out to evaluate mechanical properties of the jointed Al6061/HT590 alloys by friction stir welding (FSW). FSW was conducted under the conditions with tool rotating speed of 500 RPM and traveling speed of 300 mm/min., where Ar gas was introduced to prevent the materials from corrosion during the welding process. Electron back-scattering diffraction (EBSD) was used to characterize microstructures such as grain size, misorientation angle and crystal orientation. Evolution of intermetallic compounds in Al6061 during the process were examined in terms of morphology, size and aspect ratio at three distinct zones Al base material, heat affected zone and stir zone, where transmission electron microscope (TEM) was used. It was revealed that FSW gave rise to refinement of grains as well as growth of intermetallic compounds in Al6061. The morphological changes of intermetallic compounds exerted an influence on mechanical properties, resulting in occurrence of fracture in the part of the base material instead of the jointed parts (heat affected zone and stir zone). This study systematically evaluated the microstructural evolutions during the FSW for joining Al6061 with HT590 and their effect on mechanical properties.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.642-647
• /
• 2000

Nanocrystalline NiAl alloy containing 36at.%Al was synthesized by mechanical alloying (MA). Synthesized powder was sintered by a pulse electric current sintering (PECS) facility. Effecting parameters on the phase transformation were discussed in terms of cooling rate and time spent on heat treatment. The behavior of phase transformation for sintered parts was examined by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) method. Microstructure was observed by scanning electron microscopy (SEM). Martensitic lattice parameter and volume fraction was calculated by direct comparison method in X-ray diffraction analysis.

• Korean Journal of Materials Research
• /
• v.22 no.3
• /
• pp.140-144
• /
• 2012

Compared with bulk material, quantum dots have received increasing attention due to their fascinating physical properties, including optical and electronic properties, which are due to the quantum confinement effect. Especially, Luminescent CdSe quantum dots have been highly investigated due to their tunable size-dependent photoluminescence across the visible spectrum. They are of great interest for technical applications such as light-emitting devices, lasers, and fluorescent labels. In particular, quantum dot-based light-emitting diodes emit high luminance. Quantum dots have very high luminescence properties because of their absorption coefficient and quantum efficiency, which are higher than those of typical dyes. CdSe quantum dots were synthesized as a function of the synthesis time and synthesis temperature. The photoluminescence properties were found strongly to depend on the reaction time and the temperature due to the core size changing. It was also observed that the photoluminescence intensity is decreased with the synthesis time due to the temperature dependence of the band gap. The wavelength of the synthesized quantum dots was about 550-700 nm and the intensity of the photoluminescence increased about 22~70%. After the CdSe quantum dots were synthesized, the particles were found to have grown until reaching a saturated concentration as time increased. Red shift occurred because of the particle growth. The microstructure and phase developments were measured by transmission electron microscopy (TEM) and X-ray diffractometry (XRD), respectively.