• Korean Journal of Materials Research
• /
• v.30 no.12
• /
• pp.678-686
• /
• 2020

Microstructural characteristics of directionally solidified René 80 superalloy are investigated with optical microscope and scanning electron microscope; solidification velocity is found to change from 25 to 200 μm/s under the condition of constant thermal gradient (G) and constant alloy composition (Co). Based on differential scanning calorimetry (DSC) measurement, γ phase (1,322 ℃), MC carbide (1,278 ℃), γ/γ' eutectic phase (1,202 ℃), and γ' precipitate (1,136 ℃) are formed sequentially during cooling process. The size of the MC carbide and γ/γ' eutectic phases gradually decrease with increasing solidification velocity, whereas the area fractions of MC carbide and γ/γ' eutectic phase are nearly constant as a function of solidification velocity. It is estimated that the area fractions of MC carbide and γ/γ' eutectic phase are determined not by the solidification velocity but by the alloy composition. Microstructural characteristics of René 80 superalloy after solid solution heat-treatment and primary aging heat-treatment are such that the size and the area fraction of γ' precipitate are nearly constant with solidification velocity and the area fraction of γ/γ' eutectic phase decreases from 1.7 % to 0.955 %, which is also constant regardless of the solidification velocity. However, the size of carbide solely decreases with increasing solidification velocity, which influences the tensile properties at room temperature.

• Journal of Powder Materials
• /
• v.28 no.4
• /
• pp.331-335
• /
• 2021

The effects of drying temperature on the microstructure of porous W fabricated by the freeze-casting process of tert-butyl alcohol slurry with WO₃ powder was investigated. Green bodies were hydrogen-reduced at 800℃ for 1 h and sintered at 1000℃ for 6 h. X-ray diffraction analysis revealed that WO₃ powders were completely converted to W without any reaction phases by hydrogen reduction. The sintered body showed pores aligned in the direction of tert-butyl alcohol growth, and the porosity and pore size decreased as the amount of WO₃ increased from 5 to 10vol%. As the drying temperature of the frozen body increased from -25℃ to -10℃, the pore size and thickness of the struts increased. The change in microstructural characteristics based on the amount of powder added and the drying temperature was explained by the growth behavior of the freezing agent and the degree of rearrangement of the solid powder during the solidification of the slurry.

• Ocean and Polar Research
• /
• v.44 no.1
• /
• pp.39-59
• /
• 2022

How in the Antarctic icefish, generally, and Pseudochaenichthys georgianus, in particular, otoliths increase in size and build new material as the fish ages and passes through different life phases is largely unexplored. Morphometric details of 3418 otoliths of Ps. georgianus from S. Georgia and 318 from S. Shetland, were processed and proportions of the amounts of collagen and aragonite removed by EDTA were determined for different age groups. Microstructural investigations showed that characteristics of the 3-dimensinal collagen net are the reason for the radial direction and orientation of the aragonite needles of approximately 1.0 ㎛ in length in larval and 2.3 ㎛ in length in adult specimens. Earlier generated increment layers from the primordial centre (PC) in the dorsal direction restrict those of the secondary centre (SC), causing new growth layer accretion in different directions. In the otoliths of larval Ps. georgianus, aragonite layers are 0.89 ㎛ wide while in juveniles and adults they measure 1.45-2.86 ㎛. Otoliths change from a sphere shape in the larvae to a longish object of irregular outline in the older stages. It is tentaively suggested that the observed otolith shape differences at distinct growth stages are due to physical effects related to swimming speeds at particular water depths and locations. To confirm that otoliths, apart from being useful for age analyses, could also serve to establish correlations between developmental stage and the oceanic environment the fish spend time in, further analyses using additional species and state-of-the-art methods like µCT imaging to evaluate otolith volumes and shapes are required.

• Journal of the Korean Ceramic Society
• /
• v.53 no.1
• /
• pp.81-86
• /
• 2016

The effect of substrate rotation speed on the phase forming behavior and microstructural variation of 8 wt% yttria ($Y_2O_3$) stabilized $ZrO_2$ (8YSZ) coatings as a thermal barrier coating has been investigated. 8YSZ coatings with $100{\sim}200{\mu}m$ thickness were deposited by electron beam-physical vapor deposition onto a super alloy (Ni-Cr-Co-Al) substrate with a bond coating (NiCo-CrAlY). The width of the columnar grains of the 8YSZ coatings increased with increasing substrate rotation speed from 1 to 30 rpm at a substrate temperature range of $900{\sim}950^{\circ}C$. In spite of the different growth behaviors of coatings with different substrate rotation speeds, the phases of each coating were not changed remarkably. Even after post heat treatments with various conditions of the coated specimens fabricated at 20 rpm, only a change of color was noticeable, without any remarkable change in the phase or microstructure.

• Applied Microscopy
• /
• v.47 no.3
• /
• pp.208-213
• /
• 2017

The microstructural changes in Co nanoparticles and an Au-10at.%Pd thin film have been investigated using an in situ heating holder with a micro-electro-mechanical system (MEMS). In Co nanoparticles, two phases (face-centered cubic and hexagonal close-packed crystal structures) were found to coexist at room temperature and microstructures at temperatures, higher than $1,000^{\circ}C$, were observed with a quick response time and significant stability. The actual temperature of each specimen was directly estimated from the changes in the lattice spacing (Bragg-peak separation). For the Au-10at.%Pd thin film, at a set temperature of $680^{\circ}C$, the actual temperature of the sample was estimated to be $1,020^{\circ}C{\pm}123^{\circ}C$. Note that the specimen temperature should be carefully evaluated because of the undesired effects, i.e., the temperature non-uniformity due to the sample design of the MEMS chip, and distortion due to thermal expansion.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.3
• /
• pp.212-218
• /
• 1996

To clarify the influence of precipitation microstructure and inclusion on the monotonic tensile fracture behaviors in 2090 alloy aged at $180^{\circ}C$, the detailed measurement of hardness, tensile strength, elongation and the observation of scanning electron micrography, transmision electron micrography have been carried out. The transgranular shear ductile fracture has been observed in specimen quenched after solution treatment at $500^{\circ}C$ for 45min. While the under-aged specimen was fractured in both transgranular shear ductile and intergranular fracture mode, the fracture mode of peak-aged and over-aged alloy was predominantly intergranular fracture. The fracture behavior of each ageing condition was influenced by the change of precipitation microstructural features. In the case of peak-aged and over-aged alloys, the coarse and heterogeneous slip band caused by both shearable nature of the ${\delta}^{\prime}(Al_3Li)$ precipitates and PFZ along the high angle grain boundary aid the localization of deformation, resulting in low energy intergranular fracture. It was also estimated that the fractured T-type intermetallic phases (inclusion) and the equilibrium ${\delta}$(AlLi) phases which were formed at grain boundaries palyed an important role in promoting intergranular fracture mode.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.1
• /
• pp.65-68
• /
• 2004

When a monolithic component of piston and rebound is produced by sintering process, some technical problems such as clogging of holes during post-machining, dimensional change around the holes, and cracking of the component edges due to concentration of mechanical stress during machining are frequently encountered. To solve these problems, we systematically evaluated and investigated the density of green compacts and sintered parts, the microstructural change around the holes, and the attenuation and durability of the sintered parts in this study. By doing so, it was able to solve above problems.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.6
• /
• pp.339-344
• /
• 2009

Recently, Laser surface treatment technologies have been used to improve wear charactenitics and fatigue resistance of metal molding. When the laser beam is irradiated on the surface and laser speed is appropriate, the laser focal position is rapidly heated and the thermal energy of surface penetrates the material after irradiation, finally imbuing it with a new mechanical characteristic by the process of self-quenching. This research estimates the material characteristic after efficient and functional surface treatment using HPDL, which is more efficient than the existing CW Nd:YAG laser heat source. To estimate this, microstructural changes and hardness characteristics of three parts (the surface treatment part, heat affect zone, and parental material) are observed with the change of laser beam speed and surface temperature. Moreover, the depth of the hardened area is observed with the change of the laser beam speed and temperature. From the results of the experiments, it has been shown that the maximum hardness is approximately 788Hv when the heat treatment temperature and the travel speed are $1150^{\circ}$ and 2 mm/sec, respectively.

• 보존과학연구
• /
• s.27
• /
• pp.145-163
• /
• 2006

This study is to be investigated through firing experiment in studio in order to reveal a physical properties of celadon according to change firing temperature. The results can be briefly summarized as below; Firstly, in measurement of color chromaticity, samples of first firing in body were effective in differentiating of changed color in samples from each other but there of second firing were not. The color of the glaze was more effective change than that of the body. Secondly, bulk density of body was increased with temperature and it was attained highest point in $1200^{\circ}C$ Additionally, water absorption ratio was most rapidly changed between $1000^{\circ}C$ and $1200^{\circ}C$Thirdly, in the microstructural analysis, body of samples in first firing have not specific characteristics in the changed patterns of microstructure. body and glaze of samples in second firing have many that. Consequently, we knew that this experiment can be provided researcher with physical properties and firing mechanisms of celadon.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.10
• /
• pp.1303-1313
• /
• 1997

A micro-macroscopic analysis on the conduction-controlled directional casting of Al-Cu alloys is performed, in which emphases are placed on the microstructural features. In order to facilitate the solution procedure, an iterative micro-macroscopic coupling algorithm is developed. The predicted results show that the effect of finite back diffusion on the transient solidification process in comparison with the lever rule depends essentially on the initial concentration of an alloy. In the final casting, the eutectic fraction is distributed in an increasing-decreasing-increasing pattern, each mode of which is named the chill, interior and end zones. This nonuniformity per se suffices to justify the necessity of this work because it originates from the combined effects of finite back diffusion and cooling path-dependent nature of the eutectic formation. As the cooling rate is enhanced, not only the influence depths of boundaries narrow, but also the eutectic fractions in the chill and interior zones increase. In addition, it is revealed for the first time that the micro segregation band is formed in response to a sudden change in cooling rate during the directional casting. An increasing change creates an overshooting band in the eutectic fraction distribution, and vice versa.