• 열처리공학회지
• /
• 제32권5호
• /
• pp.212-223
• /
• 2019

This study is to investigate the relationship between microstructural factors and tensile properties after aging heat treatment of the 15-5PH stainless steel at the temperature range of $450^{\circ}C$, $500^{\circ}C$ and $550^{\circ}C$ for various time. For the aging time of 2 hours, hardness showed maximum at $450^{\circ}C$ and then decreased with increasing aging temperature. While, hardness decreased gradually during aging $450^{\circ}C$, $500^{\circ}C$ and $550^{\circ}C$ from 1 hour to 5 hours but the hardness nearly unchanged until the 100 hours after 5 hours aging. When aging at $450^{\circ}C$, Cu atoms preferentially aggregated at the prior austenite grain boundaries and martensite lath boundaries, and Cu concentration at those boundaries was nearly unchanged even after aging for 100 hours. Therefore it was suggested that the coherency is still maintained after 100 hours aging at $450^{\circ}C$. Aging at $500^{\circ}C$ and $550^{\circ}C$ results in an increase in the concentration of Ni at the martensite lath boundaries and prior austenite grain boundaries, resulting in the formation of reversed austenite. Especially, when aged at $550^{\circ}C$ for 100 hours, the concentration of Ni remarkably increased at those boundaries, and thus the microstructure of herring bone shape was appeared. Considering the migration of Ni atom to the lath boundaries and prior austenite grain boundaries, Ni atoms contributed greatly to the formation of reversed austenite. On the other hand, it was found that Cu atoms hardly moving to those boundaries may not be contributed to the formation of reversed austenite. When aging at $450^{\circ}C$, the coarsening of the precipitated Cu atoms proceeded very slowly with increasing aging time, therefore the decrease in strengths were small but the reduction area was considerably increased due to the softening of the matrix. At the aging temperature of $500^{\circ}C$ and $550^{\circ}C$, the strengths decreased and the elongation and reduction area increased due to the appearance of the reversed austenite. Especially, the increase of reduction area was remarkable.

• 한국주조공학회지
• /
• 제38권6호
• /
• pp.111-120
• /
• 2018

In this study, the effects of two different casting methods (gravity casting and, diecasting) and various solid-solution conditions on the mechanical properties of ASC (Al-10.5wt%Si-1.75wt%Cu) and ALDC12 (Al-10.3wt%Si-1.72wt%Cu-0.76wt%Fe-0.28wt% Mn-0.32wt%Mg-0.9wt%Zn) alloys were investigated. A thermodynamic solidification analysis program (PANDAT) was used to predict the liquidus, solidus, and phases of the used alloys. In the results of an XRD analysis, ${\beta}$-AlFeSi peaks were observed only in the ALDC12 alloy regardless of the casting method or SST (solid-solution treatment) conditions. However, according to the results of a FE-SEM observation, both ${\theta}(Al_2Cu)$ and ${\beta}$-AlFeSi were found to exist besides ${\alpha}$-Al and eutectic Si in the gravity-casted ASC alloy at $500^{\circ}C$ after a SST of 120min. The ${\alpha}$-AlFeSi and ${\beta}$-AlFeSi phases including the eutectic phases were also found to exist in the ALDC12 alloy. The results of a microstructural observation and analyses by XRD, FE-SEM and EDS were in good agreement with the PANDAT results. The gravity-casted ALDC12 and ASC specimens showed the highest Y.S. and UTS values after aging for three hours at $180^{\circ}C$ after a SST at $500^{\circ}C$ for 30min. At longer solid-solution treatment times at $500^{\circ}C$ in the gravity-casted ALDC12 and ASC specimens, the elongations of the ASC alloys increased, whereas they decreased slightly in the ALDC12 alloys.

• 한국결정성장학회지
• /
• 제31권1호
• /
• pp.37-42
• /
• 2021

화학적 조성이 TiZrN 박막의 구조적 특성 및 열적 특성에 미치는 영향을 조사하였다. 증착된 TixZr1-xN(x = 0.87, 0.82, 0.7, 0.6, 0.28) 박막에서 Zr 분율이 증가함에 따라 결정립 크기가 감소하고 주상 구조에서 입계상 구조로 점진적으로 변화하는 미세구조 변화가 관찰되었다. 또한 XRD 분석을 통해 Zr 분율이 0.4까지 증가할 때 TiN 상에서 TiZrN 상으로의 점진적인 결정상 전이가 일어났음을 확인하였다. 900℃ 온도에서의 열처리 이후 Ti0.82Zr0.18N과 Ti0.7Zr0.3N 박막은 rutile 상 TiO2와 TiZrO4 산화물이 공존하는 형태로 전환된 반면에 Ti0.6Zr0.4N 박막은 TiZrO4 산화물로 변화함을 확인하였다. 다섯 가지 조성의 TiZrN 박막 중에서 Ti0.6Zr0.4N 박막이 가장 우수한 고온 안정성을 나타내었고, Inconel 617 기판의 열산화에 의해 발생하는 Cr의 표면 확산을 억제하는 열산화 저항성 향상 효과가 가장 우수함을 확인하였다.

• 한국산학기술학회논문지
• /
• 제22권2호
• /
• pp.794-801
• /
• 2021

이 연구는 electric resistance element spot welding 프로세스를 도입하여 알루미늄 합금-강철의 이종 접합부의 기계적 강도 및 내식성을 향상시키기 위해 수행되었다. SPFC980Y 강철과 Al5052-H32가 각각 모재로써 적용되었고, S20C 강철은 리벳 element로써 음각과 양각의 형상으로 구분되며, Al5052-H32에 전기 저항 스폿 용접을 위해 리벳팅 되어 6.5 kA의 전류와 250 kgf/㎠의 가압력으로 접합되었다. 그 결과, 음각된 S20C element는 스폿 용접 공정 후 불안정한 너깃이 형성되는 반면, 양각된 S20C의 경우, 구조적으로 건전한 접합부로 건전한 내식성 및 탁월한 기계적 특성이 얻어졌다. FEM 시뮬레이션의 도입으로, 음각과 양각의 계면의 접합 특성이 수치적으로 밝혀졌으며, 시뮬레이션 결과는 미세조직 발달 양상을 수치적으로 뒷받침하였다. 이 연구는 element 스폿 용접된 H32-A5052 이종 접합부의 기계적 강도 및 부식 신뢰성에 대해 체계적으로 분석되었으며, 이 공정은 금속재료뿐만 아니라, 경량 비전도성 비철/비금속계 재료에도 적용 될 수 있기 때문에, 차세대 차체 경량화의 양산 기술로 확장 될 수 있다.

• 한국주조공학회지
• /
• 제41권3호
• /
• pp.235-240
• /
• 2021

진공 가스분사법으로 제조된 Fe₇₅B₁₃P₅Nb₂Hf₁C₄ 합금의 응고중 액상의 크기와 이에 따른 냉각속도의 변화가 정출상의 형성에 미치는 영향에 대한 고찰을 하였다. 고온 액상에서 동일한 조건으로 응고된 서로 다른 크기의 액상이 구형의 분말형태로 응고될 때 크기에 따른 임계냉각속도의 차이를 계산하였으며, 액상의 평균 반지름이 3배정도 크기 차이가 날 경우 고상으로 변태할 때 임계냉각속도가 13.5배까지 차이가 나는 것을 알 수 있었다. 이러한 임계냉각 속도의 차이에 따른 정출상의 형성과 정출상의 형태와 크기에 따른 탄화물의 형성 거동을 조사하여 열역학 계산으로 예측된 결과와 비교 분석하였으며, 분말입자의 크기가 20~45 마이크론일 경우 Hf과 Nb이 포함된 MC타입의 탄화물이 초정으로 형성 되는 것을 알 수 있었으며 이때 Hf과 Nb의 비율은 합금의 조성 및 냉각속도에 따라 변화됨을 관찰 할 수 있었다.

• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.167-173
• /
• 2011

Nickel cobalt ferrite($Ni_{0.5}Co_{0.5}Fe_2O_4$) powder was prepared through the ceramic route by the calcination of a stoichiometric mixture of NiO, CoO and $Fe_2O_3$ at $1100^{\circ}C$. The pressed pellets of $Ni_{0.5}Co_{0.5}Fe_2O_4$ were isothermally reduced in pure hydrogen at $800{\sim}1100^{\circ}C$. Based on the thermogravimetric analysis, the reduction behavior and the kinetic reaction mechanisms of the synthesized ferrite were studied. The initial ferrite powder and the various reduction products were characterized by X-ray diffraction, scanning electron microscopy, reflected light microscope and vibrating sample magnetometer to reveal the effect of hydrogen reduction on the composition, microstructure and magnetic properties of the produced Fe-Ni-Co alloy. The arrhenius equation with the approved mathematical formulations for the gas solid reaction was applied to calculate the activation energy($E_a$) and detect the controlling reaction mechanisms. In the initial stage of hydrogen reduction, the reduction rate was controlled by the gas diffusion and the interfacial chemical reaction. However, in later stages, the rate was controlled by the interfacial chemical reaction. The nature of the hydrogen reduction and the magnetic property changes for nickel cobalt ferrite were compared with the previous result for nickel ferrite. The microstructural development of the synthesized Fe-Ni-Co alloy with an increase in the reduction temperature improved its soft magnetic properties by increasing the saturation magnetization($M_s$) and by decreasing the coercivity($H_c$). The Fe-Ni-Co alloy showed higher saturation magnetization compared to Fe-Ni alloy.

• 대한금속재료학회지
• /
• 제49권11호
• /
• pp.882-892
• /
• 2011

The influence of rhenium (Re) and ruthenium (Ru) addition on the solidification and solute redistribution behaviors in advanced experimental Ni-base superalloys has been investigated. A series of model alloys with different levels of Re and Ru were designed based on the composition of Ni-6Al-8Ta and were prepared by vacuum arc melting of pure metallic elements. In order to identify the influence of Re and Ru addition on the thermo-physical properties, differential scanning calorimetry analyses were carried out. The results showed that Re addition marginally increases the liquidus temperature of the alloy. However, the ${\gamma}^{\prime}$ solvus was significantly increased at a rate of $8.2^{\circ}C/wt.%$ by the addition of Re. Ru addition, on the other hand, displayed a much weaker effect on the thermo-physical properties or even no effect at all. The microsegregation behavior of solute elements was also quantitatively estimated by an electron probe microanalysis on a sample quenched during directional solidification of primary ${\gamma}$ with the planar solid/liquid interface. It was found that increasing the Re content gradually increases the microsegregation tendency of Re into the dendritic core and ${\gamma}^{\prime}$ forming elements, such as Al and Ta, into the interdendritic area. The strongest effect of Ru addition was found to be Re segregation. Increasing the Ru content up to 6 wt.% significantly alleviated the microsegregation of Re, which resulted in a decrease of Re accumulation in the dendritic core. The influence of Ru on the microstructural stability toward the topologically close-packed phase formation was discussed based on Scheil type calculations with experimentally determined microsegregation results.

• 한국축산식품학회지
• /
• 제41권5호
• /
• pp.802-815
• /
• 2021

To investigate the effect of postmortem phases on lamb meat quality, the physicochemical quality, microstructure and water mobility of oyster cut, short loin, knuckle and silverside muscles from Small-Tail Han sheep were evaluated in the pre-rigor, rigor mortis and post-rigor phases. Pre-rigor lamb meat had higher pH and water holding capacity (WHC), whereas lower CIE L^*, b^*, hue angle values than rigor mortis and post-rigor meat (p<0.05). The Warner-Bratzler shear force (WBSF) values were higher in rigor mortis short loin and silverside than their pre-rigor and post-rigor counterparts, pre-rigor short loin had lower WBSF value than its post-rigor counterpart (p<0.05). Muscle fibers shrank laterally and longitudinally during the onset of rigor mortis. Rigor mortis and postrigor lamb meat exhibited wide I-bands, dark A-bands, short sarcomeres and large inter-myofibrillar spaces. The shift of immobilized water to free water and repulsion from the intra-myofibrillar space to the extracellular space result in the increase of water loss in rigor mortis and post-rigor lamb meat. The results of the principal component analysis (PCA) indicated that rigor mortis and post-rigor lamb meat had similar quality properties but different from pre-rigor lamb meat. In conclusion, the lamb meat in the pre-rigor phase had good tenderness, color and WHC. The results of this research could provide some theoretical references for lamb meat production and processing.

• 한국재료학회지
• /
• 제32권4호
• /
• pp.200-209
• /
• 2022

In this study, defects generated in the YSZ coating layer of the IN738LC turbine blade are investigated using an optical microscope and SEM/EDS. The blade YSZ coating layer is composed of a Y-Zr component top coat layer and a Co component bond coat layer. A large amount of Cr/Ni component that diffused from the base is also measured in the bond coat. The blade hot corrosion is concentrated on the surface of the concave part, accompanied by separation of the coating layer due to the concentration of combustion gas collisions here. In the top coating layer of the blade, cracks occur in the vertical and horizontal directions, along with pits in the top coating layer. Combustion gas components such as Na and S are contained inside the pits and cracks, so it is considered that the pits/cracks are caused by the corrosion of the combustion gases. Also, a thermally grown oxide (TGO) layer of several ㎛ thick composed of Al oxide is observed between the top coat and the bond coat, and a similar inner TGO with a thickness of several ㎛ is also observed between the bond coat and the matrix. A PFZ (precipitate free zone) deficient in γ' (Ni₃Al) forms as a band around the TGO, in which the Al component is integrated. Although TGO can resist high temperature corrosion of the top coat, it should also be considered that if its shape is irregular and contains pore defects, it may degrade the blade high temperature creep properties. Compositional and microstructural analysis results for high-temperature corrosion and TGO defects in the blade coating layer used at high temperatures are expected to be applied to sound YSZ coating and blade design technology.

• 대한약침학회지
• /
• 제26권1호
• /
• pp.18-26
• /
• 2023

Objectives: Terminalia chebula, the main ingredient of Altan Arur 5, has been used for many years in traditional medicine. This medicine is more effective than other drugs and is used to treat chronic gastritis and gastrointestinal disorders such as peptic ulcers and esophageal reflux. Other ingredients of Altan Arur 5 are Punica granatum (pomegranate), tulip seeds, black balm, and excreta of Trogopterus xanthipes. The main ingredients of T. chebula are antibacterial and analgesic in traditional medicine. Despite having been used for many years and although many studies have been conducted on the beneficial effects of this medicine and its ingredients, the toxicity of Altan Arur 5 has not yet been elucidated. Therefore, we aimed to study the toxicity of Altan Arur 5 to ensure that it is safe to use. Methods: Acute and chronic toxicity of Altan Arur 5 were assessed in 10 Kunming mice and 8 Sprague-Dawley rats, respectively, in different doses. In the acute toxicity study, Altan Arur 5 was orally administered to Kunming mice in doses of 12 g/kg, 24 g/kg, and 48 g/kg for 14 days. In the chronic toxicity study, it was orally administered to Sprague-Dawley rats in doses of 1.25 g/kg, 2.5 g/kg, and 5 g/kg for 12 weeks. Results: No significant differences were observed in the relative organ weights for mice treated with Altan Arur 5 compared with those in the control group. Furthermore, no macro- or microstructural changes were noted in the organs of any group. Conclusion: Our toxicity testing revealed that the traditional medicine Altan Arur 5 has no toxic effects in vivo.