• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1621-1628
• /
• 2003

Packaging structures to block the propagation of higher­order modes in the shielded microstrip lines are designed. Packaging for microwave circuits is necessary, basically, to isolate and protect circuits from outside environments both physically and electrically. The drawback of packaging is the possibility of higher­order mode propagation, similar to waveguide modes, as the operating frequency increases. One of Possible choices for the higher­order mode suppression is to insert diaphragms to the housing structure. The shielding effects of diaphragms are analyzed using an FEM code. Several parameters such as dispersion, mode conversion, and higher­order mode transmission and reflection are analyzed. The effect of higher­order mode suppression is eminent as the depth or width of a diaphragm is increased in the air region of the microstrip line. It is shown that inductive diaphragm structure can lower ${S_21}$ for the second­order mode incidence by 30㏈, comparing with the conventional capacitive diaphragm structure. Packaging structure analyzed in this paper can be applied usefully to the design of the microwave system in a package such as transmit/receive modules.

• Journal of Navigation and Port Research
• /
• v.30 no.5 s.111
• /
• pp.331-334
• /
• 2006

In this paper, we designed and fabricated the lowpass filter with the wide stopband characteristics using microp- strip line. Adding the $\lambda_g/4$ open stub at the input and output ports, we developed the L-C ladder type lowpass filter using the open stub which has wide stopband characteristics. In order to reduce the entire size qf this filter, the high impedance microstrip lines were made with the meander structure. The lowpass filter was fabricated with the cutoff frequency 2.3 GHz and its measured frequency responses agree well with the simulation results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.8
• /
• pp.875-881
• /
• 2004

Fundamental results obtained from an atomic force microscope (AFM) chemically-induced direct nano-lithography process are presented, which is regarded as a simple method for fabrication nm-scale devices such as superconducting flux flow transistors (SFFTs) and single electron tunneling transistors (SETs). Si cantilevers with Pt coating and with 30 nm thick TiO coating were used as conducting AFM tips in this study. We observed the surfaces of superconducting strip lines modified by AFM anodization' process. First, superconducting strip lines with scan size 2 ${\mu}{\textrm}{m}$${\times}$2 ${\mu}{\textrm}{m}$ have been anodized by AFM technology. The surface roughness was increased with the number of AFM scanning, The roughness variation was higher in case of the AFM tip with a positive voltage than with a negative voltage in respect of the strip surface. Second, we have patterned nm-scale oxide lines on ${YBa}-2{Cu}_3{O}_{7-x}$ superconducting microstrip surfaces by AFM conductive cantilever with a negative bias voltage. The ${YBa}-2{Cu}_3{O}_{7-x}$ oxide lines could be patterned by anodization technique. This research showed that the critical characteristics of superconducting thin films were be controlled by AFM anodization process technique. The AFM technique was expected to be used as a promising anodization technique for fabrication of an SFFT with nano-channel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.5
• /
• pp.463-470
• /
• 2015

In this paper, a new dual-band bandpass filter(BPF) that has resonators and feed lines with Stepped-Impedance Resonator(SIR) structures is proposed. Feed lines with SIR structure provide maximum magnetic field points which occur at the same locations of the input and output feed lines, so the insertion loss of BPF was reduced. Applying the SIR structure to the BPF for the first passband improves rejection characteristics between the first passband and the second passband. It reduces the coupling between the BPF for the first passband and the BPF for the second passband, so it makes the dual-band BPF more compact. The proposed design method provides independent changes of both the center frequency and the bandwidth for each resonator, and also improves filtering characteristics. The validity of the proposed design method is confirmed by comparisons between the designed parameters and the measured results satisfying WLAN specifications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.436-444
• /
• 2002

This paper presents a new method, which uses defected ground structure (DGS) on the ground planes of planar transmission lines such as microstrip and coplanar waveguide (CPW), to reduce the size of amplifiers. The main idea can be summarized as follow; DGS on the ground plane of microstrip or CPW line shows an increased slow-wave effect due to the additional equivalent L-C components. So the electrical length of the transmission line with DGS is longer than that of the standard transmission line for the same physical length. Then, the length of the transmission line with DGS can be shortened in order to maintain the original electrical length to be the same. This leads the matching of the original amplifier to be kept. In order to show the proposed method is valid, two kinds of amplifiers, the original amplifier and reduced amplifier, are fabricated, measured, and compared using both microstrip and CPW. The measured performances of the reduced amplifiers with DGS are quite similar to the ones of the original amplifiers for both microstrip and CPW amplifiers, even though the size of matching networks of the amplifiers with DGS are much smaller than those of the original amplifiers.

• Journal of Satellite, Information and Communications
• /
• v.10 no.2
• /
• pp.80-85
• /
• 2015

In this paper, we present, an indstrial RFID layered microstrip patch antenna is designed using an inset feed method in order to improve recognition rates in a long distance as tags are attached to metal object by improving a problem of feeding power in fabricating metal tags and reducing effects of metallic object. The inset feed shows a distinctive characteristic that has no separation between emitters and feed lines differing from a structure with the conventional inductive coupling feed. This structure makes possible to produce a type that presents a low antenna height and enables impedance coupling for tag chips. Although it shows a difficulty in the impedance coupling due to increases in the parasite capacitance between a ground plane and an emitter in an antenna according to decreases in the height of a tag antenna, it may become a merit in designing the tag antenna because the antenna impedance can be determined as an inductive manner if a shorted structure is used for feeding power. Therefore, in this paper the microstrip patch antenna is designed as a modified type and applies the inset feed in order to reduce effects of metallic objects where the antenna is be attached. Also, the antenna uses a multi-layer structure that includes a metal plate between radiator and ground instead of using a single layer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.76-84
• /
• 2012

In this paper, two kinds of E-plane microstrip-to-waveguide transitions are optimally designed and fabricated for combining output power from multiple small-power amplifiers in a WR-28 waveguide because conventional K connectors cause unnecessary insertion loss and adaptor loss. The transition design is based on target specifications such as a center frequency of 35 GHz, bandwidth of ${\pm}500MHz$, 0.1 dB insertion loss and 20 dB return loss. Performance variation caused by mechanical tolerance and assembly deviation is fully evaluated by three dimensional electromagnetic simulation. The fabricated back-to-back transitions with 16 mm and 26.57 mm interstage microstrip lines show insertion loss per transition of ~0.1 dB at 35 GHz and average 0.2 dB over full Ka band. Also the back-to-back transition shows return loss greater than 15 dB, which implies that the transition itself has return loss better than 20 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.515-525
• /
• 1998

In this paper, for both transmission and reception with single antenna system of satellite communication, dual-frequency antennas which operate simultaneously at 12.5 GHz and at 14.25 GHz are designed, constructed and measured. Also by using dual feeding structure, the problems of single-fed dual-frequency antenna such as the separation of transmitting and receiving signals and single polarization, are solved. Microstrip patch as a radiation element of dual-fed dual-frequency antenna has width and length which are the resonance lengths of the corresponding frequencies for transmission and reception, respectively. The effects of the feed line on the other frequency feeding are minimized with the optimal matching scheme for the feed lines. For solving the space problems of dual-fed two-dimensional array antennas, microstrip-line and coaxial probe feedings are used for each frequency and a two-dimensional $2\times2$ array antenna was designed and measured their characteristics. The experimental results show that errors of resonance frequencies are less than 1.44%, the return losses are less than -21 dB and the isolations between two feeding ports are less than -21 dB. The characteristics of radiation patterns of dual frequency microstrip antenna are measured and evaluated. The directivities, sidelobe levels and cross polarizations are also measured and compared with the simulations. The results show some errors due to the misalignment of coaxial probe feeding.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.301-306
• /
• 2014

We proposed a new PCB-type 'common-mode current($I_c$) and differential-mode current($I_d$) detector' working for fast detection of $I_c$ and $I_d$ from the differential-mode signaling, with miniaturization effect and possibility of cheaper fabrication. In order to realize this device, we suggest a branch-line-coupler balun having a composite right- and left-handed(CRLH) one-layer microstrip phase-shifting line as compact as roughly ${\lambda}_g/14$. The presented balun obviously is different from the conventional bent-&-folded delay lines or slits on the ground for coupling the lines on the top and bottom dielectrics. As we connect the suggested balun output ports of the differential-mode signal lines via the through-port named U and coupled-port named L, $I_c$ and $I_d$ will appear at port ${\Delta}$ and port ${\Sigma}$ of the present device, in order. The validity of the design scheme is verified by the circuit-and numerical electromagnetic analyses, and the dispersion curve proving the metamaterial characteristics of the geometry. Besides, the examples of the $I_c$ and $I_d$ indicator are observed as the even and odd modes in differential-mode signal feeding. Also, the proposed device is shown to be very compact, compared with the conventional structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.554-559
• /
• 2004

A novel miniaturized 2-pole band pass filter(BPF) is proposed and it has an overlapped hairpin and slot structure on the upper and bottom plane of microstrip lines. Due to the overlapped structure of a hairpin and a slot, the size of the proposed BPF is quite smaller than that of a general BPF having coupled lines. The size of the proposed BPF is reduced to 33 % comparing with the conventional λ/4 coupled BPF. The attenuation is improved by controlling the attenuation poles properly using the proposed structure. The proposed 2-pole BPF is fabricated with a narrow bandwidth(69 ㎒) at center frequency, 1.9 ㎓ which is difficult to make that narrow bandwidth in the conventional coupled lines due to impractical spacing. The design method in this paper can be applied to the design of other microwave circuits to reduce the size and improve the performances.