• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2133-2139
• /
• 2012

A new system using $TiO_2$ (nano-sized, band-gap 3.14 eV)-impregnated spherical ZnS (micro-sized, band-gap 2.73 eV) nano/micro-composites (Ti 0.001, 0.005, 0.01, and 0.05 mol %/ZnS) was developed to enhance the production of hydrogen from methanol/water splitting. The ZnS particles in a spherical morphology with a diameter of about 2-4 mm which can absorb around 455 nm were prepared by hydrothermal method. This material was used as a photocatalyst with loading by nano-sized $TiO_2$ (20-30 nm) for hydrogen production. The evolution of $H_2$ from methanol/water (1:1) photo splitting over the $TiO_2$/ZnS composite in the liquid system was enhanced, compared with that over pure $TiO_2$ and ZnS. In particular, 1.2 mmol of $H_2$ gas was produced after 12 h when 0.005 mol % $TiO_2$/ZnS nano/micro-composite was used. On the basis of cyclic voltammeter (CV) and UV-visible spectrums results, the high photoactivity was attributed to the larger band gap and the lower LUMO in the $TiO_2$/ZnS composite, due to the decreased recombination between the excited electrons and holes.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.1
• /
• pp.52-59
• /
• 2004

Recently, many researches for fine particles plasma have been focused on the fabrication of the new devices and materials in micro-electronic industry, although reduction or elimination of fine particles was interested in plasma processing until now on. In order to enhance their utilization, it is necessary to control and analyze fine particle behavior. Therefore, we developed simulation model of fine particles in RF Ar plasmas. This model consists of the calculation parts of plasma structure using a two-dimensional fluid model and of fine particle behavior. The motion of fine particles was derived from the charge amount on the fine particles and forces applied to them. In this paper, Ar plasma properties using two-dimensional fluid model without fine particles were calculated at power source voltage 15[V] and pressure 0.5[Torr]. Time-averaged spatial distributions of Ar plasma were shown. The process on the formation of Coulomb crystal of fine particles was investigated and it was explained by combination of ion drag and electrostatic forces. And also analysis on the forces of fine particles was presented.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.12
• /
• pp.5-12
• /
• 2011

Macro- and micro-behaviors of soluble granular media during dissolution process is investigated by numerical analysis. Soluble media are represented by assemblies of non-soluble particles and soluble particles with the different soluble particles contents. Dissolutions of particles are implemented by reducing sizes of soluble particles. The numerical simulations results exhibit that the vertical displacements increase to certain times and become constant while the porosities still increase until no soluble particles are present. However, the porosities and vertical displacements increase with the increase of soluble particles content. The microscopic views show that the fabrics of media change during dissolution process until the certain times, the higher soluble particles contents, and the larger change in fabric.

• Journal of the Korean Society of Visualization
• /
• v.1 no.1
• /
• pp.75-81
• /
• 2003

A custom micro-PIV optics assembly has been used to measure the flow fold inside a T-junction of a microchannel. The micro-PIV system consists of microscope objectives of various magnifications, a dichroic cube, and an 8-bit CCD camera. Fluorescent particles of diameters 620 nm have been used with a Nd:YAG laser and color filters. A programmable syringe pump with Teflon tubings were used to inject particle-seeded distilled water into the channel at flow rates of 2.0, 4.0, 6.0 mL/hr. The micro-channels are fabricated with PDMS with a silicon mold, then O$_{2}$ -ion bonded onto a slide glass. Results show differences in flow characteristics and resolution according to fluid injection rates, and magnifications, respectively. The results include PIV data with vector-to-vector distances of 2 $\mu$m with 32 pixel-square interrogation windows at 50$\%$ overlap.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.10
• /
• pp.1802-1806
• /
• 2007

Nowadays, many configurations and applications of small atmospheric plasma source have been investigated with growing interest, as it provides the bacteria inactivation, the surface modification and removal of unwanted small regions, and so on. In this paper, the non-thermal micro plasma source under atmospheric pressure by means of submicrosecond pulse voltage waveforms is suggested. Plasma operates in helium is appears as a small (sub-mm) glow at the tip of a plasma gun. Electrical measurements show that the plasma source operates at low voltage (about 500V) and the power consumption is about 1W at 25kHz. Moreover, the emission spectrum shows the relatively higher emission intensity of oxygen particles than those of helium and nitrogen.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.419-422
• /
• 2002

A three-dimensional inlet flow structure inside a microfluidic element has been investigated using a micro-PIV(particle image velocimetry) measurement as well as a numerical analysis. The present study employs a state-of-art micro-PIV system which consists of epi-fluorescence microscope, 620nm diameter fluorescent seed particles and an 8-bit megapixel CCD camera. For the numerical analysis, a commercial software CFD-ACE+(V6.6) was employed for comparison with experimental data. Fixed pressure boundary condition and a 39900 structured grid system was used for numerical analysis. Velocity vector fields with a resolution of $6.7{\times}6.7{\mu}m$ has been obtained, and the attention has been paid on the effect of varying measurement conditions of particle diameter and particle concentration on the resulting PIV results. In this study, the microfluidic elements were fabricated on plastic chips by means of MEMS processes and a subsequent melding process.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.400-404
• /
• 2001

A micro-PIV(particle image velocimetry) measurement has been conducted to investigate flow fields in such microfluidic devices as microchannels and micronozzle. The present study employs a state-of-art micro-PIV system which consists of epi-fluorescence microscope, 620nm diameter fluorescent seed particles and an 8-bit megapixel CCD camera. Velocity vector fields with a resolution of $6.7\times6.7{\mu}m$ has been obtained, and the attention has been paid on the effect of varying measurement conditions of particle diameter and particle concentration on the resulting PIV results. In this study, the microfluidic elements were fabricated on plastic chips by means of MEMS processes and a subsequent molding process. Flow fields in a variety of microchannels as well as micronozzle have been investigated.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.251-256
• /
• 2006

The purpose of this study was to confirm multiple retention system of C-PAM, A-PAM and Inorganic micro particles vs. traditional micro particle system and dual polymer system by measuring retention, drainage and formation using RDA HSF and Techpap 2D -F Sensor The benefits of dual polymer system were easy to use, low chemical consumption and good retention property but defect was worse drainage property than inorganic microparticle systems. On the other hand, Inorganic microparticle system had benefit of good drainage effect but defects were difficult to use, high chemical consumption. Therefore, we tried to find optimal morphology of polyacrylamide and applied to multiple retention system of C-PAM, A-PAM and inorganic microparticles to compensate defects of both of retention systems. As a result, we found the performance of branched C-PAM, branched A-PAM and inorganic micro particle triple system was more appropriate than traditional inorganic mircoparticle systems or dual polymer systems by comparing retention, drainage and formation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.597-600
• /
• 2004

Fabrication technique and performance test of catalytic micro propulsion are treated based on MEMS technology. This propulsion is designed to use hydrogen peroxide as liquid mono-propellant for attitude control of pica-satellite. The propellant is fed into the micro reactor channel and decomposed into hot gas yielding controllable thrust by catalyst. In order to increase the efficiency of the reaction that depends on the contact area of propellant and catalyst, porous surface formation on the channel accompanied by platinum particle deposition has been performed using H$_2$PtCl$_{6}$ solution as a precursor. Several thrusters were fabricated in different concentration of H$_2$PtCl$_{6}$ solution to determine the best quantity of Pt particles. For the comparison of the performance of each thruster, the volume of oxygen generated by the decomposition of hydrogen peroxide and the thrust were measured.red.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.72-79
• /
• 2002

The effects of carbon black on the critical J-value and the surface fracture morpology of the carbon-black filled natural rubbers were investigated. Different kinds of carbon blacks resulted in different critical J-values, surface, and roughness. It was noticed that the critical J-value was almost the same regardless of the length of a pre-crack. In addition, different kinds of carbon blacks resulted in different fracture morphologies, and micro-scale and macro-scale roughnesses. The critical J-value could be linearly expressed by the micro-scale roughness and the macro-scale roughness and it seemed related to the size distribution of carbon black particles. And we also found that the macro-scale ms roughness was more sensitive than the micro-scale ms roughness to the critical J-value by the result of correlation coefficient, r$^2$.