• Journal of Korean Neurosurgical Society
• /
• v.55 no.2
• /
• pp.92-95
• /
• 2014

Ehlers-Danlos syndrome (EDS) is a rare inherited connective disease. Among several subgroups, type IV EDS is frequently associated with spontaneous catastrophic bleeding from a vascular fragility. We report on a case of carotid-cavernous fistula (CCF) in a patient with type IV EDS. A 46-year-old female presented with an ophthalmoplegia and chemosis in the right eye. Subsequently, seizure and cerebral infarction with micro-bleeds occurred. CCF was completely occluded with transvenous coil embolization without complications. Thereafter, the patient was completely recovered. Transvenous coil embolization can be a good treatment of choice for spontaneous CCF with type IV EDS. However, every caution should be kept during invasive procedure.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1985-1987
• /
• 2002

Silicon bulk micromachined micromirrors are designed and fabricated for out-of-plane right angle reflection. The micromirror is comprised of a minor plate, springs, magnetic bars and electrodes. Single crystalline silicon is used for a flatness improvement of a mirror plate. Out-of-plane right angle reflection requires a 45 degree operation of the micromirror. The micromirrors are operated by applying a magnetic field, which is generated by a coil located below a substrate. For an individual mirror operation, each mirror is clamped using an electrostatic force against the electromagnetic force. Angular deflections are measured and compared with theoretical data. The micro mirror operates up to 45 degree when magnetic field is 4 kA/m which is generated by a 115 mA coil current Simple addressing is tested, and it is shown that a clamping voltage is less than 5V.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1154-1156
• /
• 1999

This paper presents the novel fabrication of an electromagnetic micro actuator with a corrugated diaphragm and a flat one. The actuator consists of a Parylene diaphragm with a spiral copper coil and a permanent magnet. The cower coil is fabricated by electroplating and patterning. As the further works, the frequency response of the actuator are obtained by using a laser vibrometer and the static deflection of the actuator diaphragm are measure by using laser displacement meter. The corrugated diaphragm is expected to be better than the flat one with respect to the actuator performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.58-63
• /
• 2002

For the experiment the four types of spacer were distinguished by arrangement. The flashover characteristic on each types of spacer was investigated and the flashover phenomena were observed to understand breakdown mechanism in liquid nitrogen($LN_{2}$). The spacer should be placed interior coil as an insulator, a cooling channel and s supporter of structures. The simulated electrode used in the experiment was made from five turns of HTS tape. Experimental results revealed that multi-layer and barrier effects did work well in Air but did not in $LN_{2}$. These result suggested that the flashover in LN2 caused by the bubbles due to partial discharge at micro gap, g. The flashover characteristics decreased to 70% when g is 0.2 mm. The degradation was improved by even treatment on surface of coil electrode.

• Investigative Magnetic Resonance Imaging
• /
• v.13 no.2
• /
• pp.171-176
• /
• 2009

Purpose : To investigate the effect of coating material in RF coil, which is one of main parts in MRI machine, on the Q-factor and SNR(signal-to-noise ratio) in MR images. Materials and Methods : RF coils with inner diameter of 1.7 mm were made by using copper wires coated with polyester, polyurethane, polyimide, polyamideimide, and polyester-imide, and by using copper wires in which coating materials had been removed. Q-factors of the RF coils were measured by network analyzer, and SNR values in the spin-echo MR images obtained by 600 MHz (14.1 T, Bruker DMX600) micro-imaging system for the coated and uncoated cases. Results : The measured SNRs were almost same for the RF coils with coat-removed copper wires, however SNRs and Q-factors were different for the coated cases depending on the coating material. They were maximized in the polyurethane-coated case in which the SNR was > 30% greater than polyester-coated case. Conclusion : We made solenoid-type RF coils which were easily used for MR micro-imaging in Bruker MRI probe. There was a significant coating-material dependence in the measured Q values and SNRs for the home-made RF coils. The study demonstrated that the choice of coating material of RF coil may be a critical factor in the MRI sensitivity based on SNR value.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.395-400
• /
• 2008

Alternating magnetic field was used for detection of surface flaws on nonmagnetic and magnetic metallic specimens. The nondestructive sensor probe was composed of the planar coil with inductive magnetic thin film yoke as a sensing component and a single straight typed exciting coil. The planar inductive coil sensor with magnetic yoke was fabricated by sputtering, electroplating, dry etching and photolithography process. The alternative currents with the range of 0.1A to 1.0A (0.7 MHz to 1.8 MHz) were applied to the exciting coil. The specimens were prepared with the slit shaped artificial surface flaws (minimum depth and width; 0.5 mm) on metallic plate (Al; nonmagnetic metal and FeC; magnetic metal). The detected signal for the positions and shapes of surface flaws on specimens were obtained with high sensitivity and high signal to ratio. The measured output signals by the non-contacted scanning on surface of FeC specimen with micron-sized crack were converted to the images of the flaws. And these results were compared with the optical images, respectively.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.374-380
• /
• 2011

Carbon coils could be synthesized on nickel catalyst layer-deposited silicon oxide substrate using $C_2H_2$ and $H_2$ as source gases and $SF_6$ as an additive gas under thermal chemical vapor deposition system. The characteristics (formation density and morphology) of as-grown carbon coils according to the injection stage of $SF_6$ gas incorporation were investigated. A continuous injecting of $SF_6$ gas flow could give rise to many types of carbon coils-related geometries, namely linear tub, micro-sized coil, nano-sized coil, and wave-like nano-sized coil. However, the limitation of the geometry as the nano-sized geometries of carbon coils could be achieved by the incorporation of $SF_6$ in a short time (1 min) during the initial deposition stage. A delayed injection of a short time $SF_6$ gas flow can deteriorate the limitation of the geometries. It confirms that the injection time and its starting point of $SF_6$ gas flow would be very important to determine the geometries of carbon coils.

• Journal of Korean Neurosurgical Society
• /
• v.65 no.6
• /
• pp.772-778
• /
• 2022

Objective : Endovascular treatment of large, wide-necked intracranial aneurysms by coil embolization is often complicated by low rates of complete occlusion and high rates of recurrence. A flow diverter device has been shown to be safe and effective for the treatment of not only large and giant unruptured aneurysms, but small and medium aneurysms. However, in Korea, its use has only recently been approved for aneurysms <10 mm. This study aims to compare the safety and efficacy of flow diversion and coil embolization for the treatment of unruptured aneurysms ≥7 mm. Methods : The participants will include patients aged between 19 and 75 years to be treated for unruptured cerebral aneurysms ≥7 mm for the first time or for recurrent aneurysms after initial endovascular coil embolization. Participants assigned to a flow diversion cohort will be treated using any of the following devices : Pipeline Flex Embolization Device with Shield Technology (Medtronic, Minneapolis, MN, USA), Surpass Evolve (Stryker Neurovascular, Fremont, CA, USA), and FRED or FRED Jr. (MicroVention, Tustin, CA, USA). Participants assigned to a coil embolization cohort will undergo traditional endovascular coiling. The primary endpoint will be complete occlusion confirmed by cerebral angiography at 12 months after treatment. Secondary safety outcomes will evaluate periprocedural and post-procedural complications for up to 12 months. Results : The trial will begin enrollment in 2022, and clinical data will be available after enrollment and follow-up. Conclusion : This article describes the aim and design of a multi-center, randomized, open-label trial to compare the safety and efficacy of flow diversion versus traditional endovascular treatment for unruptured cerebral aneurysms ≥7 mm.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.195-197
• /
• 1993

In this paper, a planar vibratory gyroscope is designed and fabricated in macro model. Elementary experiment and test are done for micro model. This gyroscope has a double gimbal structure with an active dimension $80{\times}120{\times}1\;mm^3$. Outer gimbal vibration is generated by electromagnetic force using ferrite E-core wounded by coil. Inner gimbal vibration is detected by inductive sensor. It is demonstrated' that mechanical and electrical symmetries are important for improvement of vibratory gyroscope.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2512-2514
• /
• 1998

The bending actuator using zigzag type shape memory alloy springs has been fabricated and characterized. The small sized actuator with outer diameter of 3.0mm and inner diameter of 2.0mm could be implemented because zigzag type spring has advantages for thin wall type actuator over the coil type spring. The measured characteristics of the fabricated bending actuator show the possibility of practical application to micro active bending catheter.