• Journal of Korea Foundry Society
• /
• v.27 no.4
• /
• pp.179-183
• /
• 2007

The TiC layer was formed on Ti and Ti alloys by plasma carburizing method. The main experimental parameters for plasma car boozing were temperature and time. XRD, EDX, hardness test and corrosion test were employed to analyze the evolution and material properties of the layer. The preferred orientation of TiC layers is (220) at treated temperature of $700^{\circ}C\;and\;880^{\circ}C$ However, it is changed to (200) at temperature of $800^{\circ}C$ The thickness of carbide layer increase with increasing carburizing temperature. Highest hardness of hardened layer formed on CP-Ti was obtained at the carburizing condition of processing temperature $880^{\circ}C$ and processing time 1080min. The corrosion potential of carburizing specimen was higher than untreated CP-titanium, and corrosion potential increased as carburizing temperature and time increased. Thus the corrosion resistance of CP-Ti was greatly enhanced after plasma carburizing treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.4
• /
• pp.200-205
• /
• 2015

Effects of austenite on the uniform corrosion in the solution of $1\;N\;H_2SO_4$ were investigated through the electrochemical polarization test. Two phases structures of martensite and austenite were obtained by annealing treatment at the range of $500^{\circ}C{\sim}700^{\circ}C$ for 10min. in 70% cold-rolled 202 stainless steel. Volume fraction of reversed austenite increased rapidly with an increase of annealing temperature. Uniform Corrosion was occur mainly on martensite phase in 202 austenitic stainless steel with two phase of austenite and martensite. Corrosion current density increased with an increase of volume fraction of austenite, therefore uniform corrosion was affected by volume fraction of austenite

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.268-273
• /
• 1998

Effect of aging treatment on the microstructures and mechanical properties of 6N01 Aluminium alloy was investigated by differential scanning calorimetry, transmission electron microscopy, microhardness measurement and tensile test. It was found that the precipitation sequence of 6N01 Aluminium alloy was GP zone ${\rightarrow}$ metastable hexagonal $Mg_2S_i({\beta}^{\prime})$,${\rightarrow}$ equilibrium fcc $Mg_2S_i({\beta})$, and the precipitates at peak aged condition were GP zones and ${\beta}^{\prime}$ phase. Microhardness changes during over aged condition showed very small decrease upon increased aging time. This result was attributed to the very slow transformation rate of ${\beta}^{\prime}$ to ${\beta}$. Maximum hardness(116 Hv) and tensile strength(312.6MPa) with 22.3% elongation were obtained from the specimen aged at $180^{\circ}C$ for 15hrs.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.6
• /
• pp.295-301
• /
• 2014

In this study, the relationship between strength and damping capacity of annealed magnesium alloys after hot rolling was investigated. The microstructure of hot rolled magnesium consisted of dendrite structure and $Mg_{17}Al_{12}$ compounds precipitated along the grain boundary. The dendrite structure was dissipated, $Mg_{17}Al_{12}$ compounds was decomposed by annealing, and then its dissolved in ${\alpha}$-Mg. With an increasing the annealing temperature and time, strength was slowly decreased and damping capacity was slowly increased by the growth of grain size and decreasing of defects induced by hot rolling. In annealing treatmented magnesium alloys after hot rolling, damping capacity was decreased rapidly with an increase of strength. There was on proportional relationship between tensile strength, and damping capacity.

• Journal of Korea Foundry Society
• /
• v.19 no.1
• /
• pp.38-46
• /
• 1999

Microstructural characteristics and strengthening behavior in Mg-5wt%Zn-0.6wtZr alloys have been investigated by a combination of optical, secondary electron and transmission electron microscopy, differential thermal analysis, and hardness and tensile, creep property measurements. The result have been compared with those of Mg-5wt%Zn alloys. The as-squeeze cast microstructure consisted of dendrite ${\alpha}-Mg$, interdendrite or intergranular $Mg_7Zn_3$ and fine dispersoids of $ZnZr_2$. The size of secondary solidification phases in Mg-5wt%Zn-0.6wtZr alloys was significantly smaller than that of the Mg-5wt%Zn alloys due to the existence of fine dispersoid of $ZnZr_2$ which also effected the refinement of grain size. TEM study showed that the main cause of age hardening is formation of fine rodlike ${\beta}_1\;'$ precipitates as well as fine $ZnZr_2$ dispersoids. Due to the observed microstructural characteristics mechanical propeties of Mg-5wt%Zn-0.6wtZr alloys was found to be superior to those of Mg-5wt%Zn alloys.

• Journal of Korea Foundry Society
• /
• v.17 no.3
• /
• pp.267-275
• /
• 1997

Fabrication of high strength Mg-Li-Al alloys by squeeze casting was established by the stabilization of melt and mold temperatures, applied pressure and the refining method. The entrapment of inclusions during pouring was prevented using 30 ppi alumina foam filter. The as-cast microstructure consists of a mixture of ${\alpha}$ and ${\beta}$ phases including AILi and $MgLi_2$, Al particles, which are distributed in the ${\beta}$ matrix. The grain sizes of gravity and squeeze casting alloys were 288 ${\mu}m$ and 207 ${\mu}m$ respectively. The addition of Al in Mg-Li alloys promoted the formation of second phase particles, which were adjusted to optimize the properties of Mg-Li-Al alloys. The Mg-10wt%Li-5wt%Al alloy after heat treatment at $350^{\circ}C$ for 1 hour showed the maximum hardness value. This is due to the facts that the amounts of ${\alpha}$ and ${\beta}$ phases and their distributions are dependent upon the solution treatment temperature, and that the amounts of AILi and $MgLi_2Al$ particles are dependent upon the Al content.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.3
• /
• pp.190-196
• /
• 2002

Ni/MH 박막전지의 전극으로 사용될 수 $Mg_{2}Ni$박막을 스퍼터링방법으로 제조하였다. $Mg_{2}Ni$합금박막은 Mg, Ni타?을 이용하여 동시에 스퍼터링함으로서 제조하였다. KOH 액체전해질 및 $Ni(OH)_2$전극을 이용하여 전기화학실험을 하였다. $Mg_2Ni$ 박막의 초기 싸이클 특성에 미치는 열처리 효과를 조사하기 위하여, $200-550^{\circ}C$로 변화시키면서 진공중에서 열처리를 하였다. 열처리온도가 $300^{\circ}C$ 이하에서는 초기방전용량이 증가하였으며, $400^{\circ}C$ 열처리시에는 활성화시의 방전용량이 약 160mAh/g으로 가장 크게 나타났다.

• Journal of Korea Foundry Society
• /
• v.14 no.1
• /
• pp.75-81
• /
• 1994

It is very important to obtain high performance ductile iron by addition a small amount of alloying elements. In this study, to improve the characteristics of small piston ring casted from ductile iron melt a small amount of boron($0{\sim}0.008wt.%$) that is powerful carbide stabilizer was added in ductile iron, and inspected it`s effects on the microstructure, wear resistance, machinability and mechanical properties. The results obtained from this study are as follows. 1. As the amount of boron increased to 0.04wt.%, the machinability of ductile iron is increased, and if the amount is in excess of 0.04wt.% the machinability is decreased conversely. 2. The wear resistance of ductile iron is improved by boron addition. 3. The recommended ladle addition of boron amount ranges from 0.04wt.% to 0.06wt.% for the use of small piston ring.

• Journal of Korea Foundry Society
• /
• v.14 no.1
• /
• pp.28-34
• /
• 1994

Metallurgical-grade polycrystalline silicon was directionally solidified at growth rates of $0.2{\sim}1.0mm/min$ by using split type, reusable graphite molds which were coated with $Si_3N_4$ powder. The resultant grain sizes of the silicon ingots and the shapes of the solid/liquid(S/L) interfaces were investigated. X-ray diffraction was used to determine the preferred orientation in each of the silicon ingots. The impurity content of the silicon was analyzed and the resistivities of the ingots were measured. During the growth of an ingot, the shape of the S/L interface was concave to the silicon melt, and the resistivity decreased. The presence of Al which can be acting as a carrier, is thought to be the main factor causing such a decrease in resistivity. When a growth rate of 0.2㎜/min was used, the preferred orientation was found to be (111).

• Korean Journal of Metals and Materials
• /
• v.50 no.1
• /
• pp.45-51
• /
• 2012

Thermodynamics of carbon in manganese alloy melts is important in manufacturing low carbon ferromanganese and silico-manganese alloys. In order to predict the carbon solubility in liquid $Mn-Si-Fe-C_{sat}$ alloys as a function of melt composition and temperature, thermodynamic interactions among carbon, silicon and iron in carbon saturated liquid manganese should be known. In the present study, the effects of silicon and iron on the carbon solubility in Mn-Si, Mn-Fe and Mn-Si-Fe melts were measured in the temperature range from 1673 to 1773 K. The carbon solubility decreases significantly as silicon and iron contents increase in liquid manganese alloy. The interaction parameters among carbon, silicon and iron in carbon saturated liquid manganese were determined from the carbon solubility data and the Lupis' relation for the interaction coefficient at constant activity.