• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 추계학술발표회 초록집
• /
• pp.4-5
• /
• 2006

This paper represents modeling and optimization techniques for solar cell process on single-crystalline float zone (FZ) wafers with high efficiency; There were the four significant processes : i)emitter formation by diffusion, anti-reflection-coating (ARC) with silicon nitride using plasma-enhanced chemical vapor deposition (PECVD); iii)screen-printing for front and back metallization; and iv)contact formation by firing. In order to increase the performance of solar cells, the contact formation process is modeled and optimized. This paper utilizes the design of experiments (DOE) in contact formation to reduce process time, fabrication costs. The experiments were designed by using central composite design which is composed of $2^4$ factorial design augmented by 8 axial points with three center points. After contact formation process, the efficiency of the solar cell is modeled using neural networks. This model is used to analyse the characteristics of the process, and to optimize the process condition using genetic algorithms (GA). Finally, find optimal recipe for solar cell efficiency.

• Korea-Australia Rheology Journal
• /
• 제14권2호
• /
• pp.63-70
• /
• 2002

Chemical mechanical planarization (CMP) is the polishing process enabled by both chemical and mechanical actions. CMP is used in the fabrication process of the integrated circuits to achieve adequate planarity necessary for stringent photolithography depth of focus requirements. And recently copper is preferred in the metallization process because of its low resistivity. We have studied the effects of chemical reaction on the polishing rate and surface planarity in copper CMP by means of numerical simulation solving Navier-Stokes equation and copper diffusion equation. We have performed pore-scale simulation and integrated the results over all the pores underneath the wafer surface to calculate the macroscopic material removal rate. The mechanical abrasion effect was not included in our study and we concentrated our focus on the transport phenomena occurring in a single pore. We have observed the effects of several parameters such as concentration of chemical additives, relative velocity of the wafer, slurry film thickness or ash)tract ratio of the pore on the copper removal rate and the surface planarity. We observed that when the chemical reaction was rate-limiting step, the results of simulation matched well with the experimental data.

• 한국레이저가공학회지
• /
• 제2권3호
• /
• pp.52-61
• /
• 1999

The laser induced forward transfer(LIFT) technique employs a pulsed laser to transfer parts of a thin metal film from an optically transparent target onto an arbitrary substrate in close proximity to the metal film on the target. In this work, a two-step method, the combination of LIFT process, in which a Au film deposited on the $Al_2$O$_3$ substrate by Nd:YAG laser and subsequent Au electroless metal plating on the by LIFT process generated Au seed, was presented. The influence of laser parameters, wavelength, laser power, film thickness and overlap ratio of pulse tracks, on the shapes of deposit and conductor line after electroless plating is experimentally studied. As a results, the threshold power densities for ablation, deposition and metallization were determined and comparison of threshold value between the wave length 1064nm and the second harmonic generated 532nm. In odor to determine a possible application in the electronic industry, a smallest conduct spot size, line width and isolated line space were generated.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.908-909
• /
• 2006

The HTCC based multilayer structure plasma head unit have some difficulties in fabrication due to complicated post-processes, such as heat treatment at reduced atmosphere, re-bonding of each layer, and silver metallization. On the other hand, LTCC based technology provides relatively simple process for multilayer plasma unit except weak mechanical properties. To overcome this problem a combined scheme using both LTCC and HTCC technology has been developed in our group, recently. In this work, we report the structural design, materials selection, joining of LTCC with HTCC substrate, and co-firing process for the fabrication of multilayered atmospheric plasma head unit.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.93-94
• /
• 2005

Cu metallization using electrochemical plating(ECP) has played an important role in back end of line(BEOL) interconnect formation. In this work, we studied the optimized copper thickness using Bottom-up Gap-fill in Cu ECP, which is closely related with the pattern dependencies in Cu ECP and Cu dual damascene process at 0.13 ${\mu}m$ technology node. In order to select an optimized Cu ECP thickness, we examined Cu ECP bulge, Cu CMP dishing and electrical properties of via hole and line trench over dual damascene patterned wafers split into different ECP Cu thickness.

• 방사성폐기물학회지
• /
• 제8권1호
• /
• pp.77-84
• /
• 2010

상용원자로에서 발생하는 산화물 사용후핵연료의 부피감용과 재활용을 위하여 산화물을 금속으로 환원시키는 공정에 대한 연구가 수행되어 왔다. 다양한 환원법 중에서, 한국원자력연구원은 LiCl-$Li_2O$ 용융염을 반응매질로 사용하는 전해환원공정을 현재 개발 중이다. 파이로 공정의 전단부에 해당하는 전해환원 공정은 PWR 산화물 연료 주기를 소듐냉각 고속로의 금속연료 주기에 연결시켜 준다. 이 논문은 금속전환 공정을 개발/개선하고, 용량 증대를 수행한 한국원자력연구원의 노력을 요약한다.

• 한국진공학회지
• /
• 제17권6호
• /
• pp.518-522
• /
• 2008

반도체 집적도의 비약적인 발전으로 박막은 더욱 다층화 되고 선폭은 더욱 미세화가 진행되었다. 이러한 악조건에서 소자의 집적도를 계속 향상시키기 위하여 많은 연구가 진행되고 있다. 특히 소자 집적도 향상으로 금속 배선 공정에서는 선폭의 미세화와 배선 길이 증가로 인한 RC지연이 발생하게 되었다. 이를 방지하기 위하여 Al보다 비저항이 작은 Cu를 배선물질로 사용하여야 하며, 또한 일부 공정에서는 이미 사용하고 있다. 그러나 Cu를 금속배선으로 사용하기 위해 해결해야 할 가장 큰 문제점은 저온에서 쉽게 Si기판과 반응하는 문제이다. 현재까지 본 실험실에서는 tungsten (W)을 주 물질로 W-C-N (tungsten- carbon - nitrogen) 확산방지막을 증착하여 연구를 하였으며, $\beta$-ray, XRD, XPS 분석을 통하여 고온에서도 Cu의 확산을 효과적으로 방지한다는 연구 결과를 얻었다. 이 연구에서는 기존 연구에 추가적으로 W-C-N 확산방지막의 표면을 Nano-Indenter System을 이용하여 확산방지막 표면강도 변화를 분석하여 확산방지막의 물성 특성을 연구하였다. 이러한 연구를 통하여 박막내 불순물인 질소가 포함된 박막이 고온 열처리 과정에서 보다 안정적인 표면강도 변화를 나타내는 연구 결과를 얻었으며, 이로부터 박막의 물성 분석을 실시하였다.

• 한국재료학회지
• /
• 제17권9호
• /
• pp.484-488
• /
• 2007

Mo(Ti) alloy and pure Cu thin films were subsequently deposited on $SiO_2-coated$ Si wafers, resulting in $Cu/Mo(Ti)/SiO_2$ structures. The multi-structures have been annealed in vacuum at $100-600^{\circ}C$ for 30 min to investigate the outdiffusion of Ti to Cu surface. Annealing at high temperature allowed the outdiffusion of Ti from the Mo(Ti) alloy underlayer to the Cu surface and then forming $TiO_2$ on the surface, which protected the Cu surface against $SiH_4＋NH_3$ plasma during the deposition of $Si_3N_4$ on Cu. The formation of $TiO_2$ layer on the Cu surface was a strong function of annealing temperature and Ti concentration in Mo(Ti) underlayer. Significant outdiffusion of Ti started to occur at $400^{\circ}C$ when the Ti concentration in Mo(Ti) alloy was higher than 60 at.%. This resulted in the formation of $TiO_2/Cu/Mo(Ti)\;alloy/SiO_2$ structures. We have employed the as-deposited Cu/Mo(Ti) alloy and the $500^{\circ}C-annealed$ Cu/Mo(Ti) alloy as gate electrodes to fabricate TFT devices, and then measured the electrical characteristics. The $500^{\circ}C$ annealed Cu/Mo($Ti{\geq}60at.%$) gate electrode TFT showed the excellent electrical characteristics ($mobility\;=\;0.488\;-\;0.505\;cm^2/Vs$, on/off $ratio\;=\;2{\times}10^5-1.85{\times}10^6$, subthreshold = 0.733.1.13 V/decade), indicating that the use of Ti-rich($Ti{\geq}60at.%$) alloy underlayer effectively passivated the Cu surface as a result of the formation of $TiO_2$ on the Cu grain boundaries.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.34-39
• /
• 2011

Screen printing method is a common way to fabricate the crystalline silicon solar cell with low-cost and high-efficiency. The screen printing metallization use silver paste and aluminum paste for front and rear contact, respectively. Especially the rear contact between aluminum and silicon is important to form the back surface filed (Al-BSF) after firing process. BSF plays an important role to reduces the surface recombination due to $p^+$ doping of back surface. However, Al electrode on back surface leads to bow occurring by differences in coefficient of thermal expansion of the aluminum and silicon. In this paper, we studied the properties of mono crystalline silicon solar cell for rear electrode with aluminum and aluminum-boron in order to characterize bow and BSF of each paste. The 156*156 $m^2$ p-type silicon wafers with $200{\mu}m$ thickness and 0.5-3 ${\Omega}\;cm$ resistivity were used after texturing, diffusion, and antireflection coating. The characteristics of solar cells was obtained by measuring vernier callipers, scanning electron microscope and light current-voltage. Solar cells with aluminum paste on the back surface were achieved with $V_{OC}$ = 0.618V, JSC = 35.49$mA/cm^2$, FF(Fill factor) = 78%, Efficiency = 17.13%.

• 한국표면공학회지
• /
• 제56권2호
• /
• pp.160-168
• /
• 2023

Recently, investigation on metallization is a key for a stretchable display. Amorphous metal such as Ni and Zr based amorphous metal compounds are introduced for a suitable material with superelastic property under certain stress condition. However, Ni and Zr based amorphous metals have too high resistivity for a display device's interconnectors. In addition, these metals are not suitable for display process chemicals. Therefore, we choose an aluminum based amprhous metal Al-Mo as a interconnector of stretchable display. In this paper, Amorphous Forming Composition Range (AFCR) for Al-Mo alloys are calculated by Midema's model, which is between 0.1 and 0.25 molybdenum, as confirmed by X-ray diffraction (XRD). The elongation tests revealed that amorphous Al-20Mo alloy thin films exhibit superior stretchability compared to pure Al thin films, with significantly less increase in resistivity at a 10% strain. This excellent resistance to hillock formation in the Al20Mo alloy is attributed to the recessed diffusion of aluminum atoms in the amorphous phase, rather than in the crystalline phase, as well as stress distribution and relaxation in the aluminum alloy. Furthermore, according to the AES depth profile analysis, the amorphous Al-Mo alloys are completely compatible with existing etching processes. The alloys exhibit fast etch rates, with a reasonable oxide layer thickness of 10 nm, and there is no diffusion of oxides in the matrix. This compatibility with existing etching processes is an important advantage for the industrial production of stretchable displays.