• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.1
• /
• pp.61-69
• /
• 2001

Polycarbonate(PC) membranes for oxygen enrichment from air were prepared by the wet phase inversion method. In order to improve oxygen separation performances of the PC membrane, the effect of the added ethanol(nonsolvent) and $CuCl_2$(metal salt) concentration in the casting solution on morphology, oxygen permeability ami $O_2/N_2$ separation factor of the membrane was studied. In addition, tensile strength and elongation at break of the membrane were investigated. An asymmetric membrane with a dense top layer and a porous sublayer was obtained. The thickness of the dense top layer decreased with increasing amount of nonsolvent additive. Compared with pure PC membrane without additive(metal salt), the oxygen permeability and $O_2/N_2$ separation factor of the $PC/CuCl_2$ membrane are significantly improved. The oxygen permeability and $O_2/N_2$ separation factor is $5.25{\times}10^{-9}cm^3(STP){\cdot}cm/cm^2{\cdot}sec{\cdot}cmHg$ and 4.5, respectively. This improvement might be due to good interaction between metal salt and oxygen.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.335-341
• /
• 2018

We report the catalytic effects of metal oxides on the $CO_2$ absorption rate in an aqueous potassium salt of ${\text\tiny{L}}-lysine-HCl$ using the vapor liquid equilibrium method. The best $CO_2$ absorption rate obtained through testing metal oxides in a highly concentrated potassium salt of amino acids (2.0 M) was identified using CuO. The recyclability of the metal oxides was tested over three cycles. The catalyst CuO was found to enhance the absorption rate of $CO_2$ by 61%. A possible mechanism was proposed based on NMR spectroscopy studies. Further, the effect of change in liquid absorbent viscosity on $CO_2$ absorption is discussed.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.278-284
• /
• 2004

The processes for the smelting of a metal product and the solidification of a molten salt were developed respectively to treat the products from the electrochemical reduction process. The method for the separation of a metal product in a magnesia container from the residual. salt and consequent smelting of it to a metal ingot by the multi step heating in vacuum was proposed. The new concept using a dual vessel and a salt valve was also suggested for the solidification of a molten salt into a regular size and shape which is suitable for the transport and measurement. The results obtained in the study will be applied to the design of the hot cell demonstration system of the Advanced Spent Fuel Conditioning Process of KAERI.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.20 no.1
• /
• pp.43-63
• /
• 2022

The aim of this review is to communicate some essential knowledge of the underlying mechanism of the corrosion of structural containment alloys during molten salt reactor operation in the context of prospective online monitoring in future MSR installations. The formation of metal halide species and the progression of their concentration in the molten salt do reflect containment corrosion, tracing the depletion of alloying metals at the alloy salt interface will assure safe conditions during reactor operation. Even though the progress of alloying metal halides concentrations in the molten salt do strongly understate actual corrosion rates, their prospective 1^st order kinetics followed by near-linearly increase is attributed to homogeneous matrix corrosion. The service life of the structural containment alloy is derived from homogeneous matrix corrosion and near-surface void formation but less so from intergranular cracking (IGC) and pitting corrosion. Online monitoring of corrosion species is of particular interest for molten chloride systems since besides the expected formation of chromium chloride species CrCl₂ and CrCl₃, other metal chloride species such as FeCl₂, FeCl₃, MoCl₂, MnCl₂ and NiCl₂ will form, depending on the selected structural alloy. The metal chloride concentrations should follow, after an incubation period of about 10,000 hours, a linear projection with a positive slope and a steady increase of < 1 ppm per day. During the incubation period, metal concentration show 1^st order kinetics and increasing linearly with time^1/2. Ideally, a linear increase reflects homogeneous matrix corrosion, while a sharp increase in the metal chloride concentration could set a warning flag for potential material failure within the projected service life, e.g. as result of intergranular cracking or pitting corrosion. Continuous monitoring of metal chloride concentrations can therefore provide direct information about the mechanism of the ongoing corrosion scenario and offer valuable information for a timely warning of prospective material failure.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2000.11a
• /
• pp.75-78
• /
• 2000

• Journal of Korea Foundry Society
• /
• v.17 no.4
• /
• pp.402-410
• /
• 1997

Developing a salt core for squeeze casting process, two different salt cores(pure salt core and mixed salt core) were fabricated and investigated. Pure salt core was composed of 100% NaCl and mixed salt core was made by mixtures of NaCl with MgO(1%), $Na_2B_4O_7$(2%), and talc(1%) as a binder or a strengthening agent. Salt cores were compacted to various theoretical density, heat treated, and then squeeze-cast with molten Al alloy(AC8A). The compression strength of salt cores were measured and the squeeze-cast products were examined for shape retention, infiltration of molten metal into the cores, and microstructures. The shape of salt core compacted at above 75% of the theoretical density was maintained stably. The higher theoretical density of salt cores gave higher compression strength, and the compression strength of mixed salt core was higher than that of pure salt core. Namely at 90% theoretical density, the compression strength of mixed salt core was $6.3 kg/mm^2$, compared to $4.6 kgmm^2$ for pure salt core. At a squeeze casting pressure of $1000 kg/cm^2$, molten Al alloy was infiltrated into pure salt core of under 85% of the theoretical density. At squeeze casting pressure of $1000 kg/cm^2$, only mixed salt core above 90% of the theoretical density were valid, but the shape of the core was altered in the case of pure salt core at 90% of theoretical density. A key factor for developing a salt core for squeeze casting process was estimated as the ultimate compressive strength of salt core.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.7
• /
• pp.1014-1019
• /
• 2012

This study was conducted to evaluate the heavy metal contents of mudflat solar salt, salt water, and sea water produced in the nationwide salt pan. In mudflat solar salt, moisture contents were significantly different (p<0.001) between regions, ranging from 7.357% to 14.862%. Arsenic (As) content ranged from 0.007 ppm to 0.497 ppm, cadmium (Cd) from 0.000 ppm to 0.101 ppm, plumbum (Pb) from 0.000 ppm to 0.191 ppm, hydrargyrum (Hg) from 0.006 ppb to 0.180 ppb, and copper (Cu) from 0.039 ppm to 4.794 ppm between regions, which were significantly different (p<0.001). Further, As, Cd, Pb, and Hg contents of sea and salt water were not in excess of their criterion points. Our results suggest that heavy metal contents of mudflat solar salt, salt water, and sea water produced in the nationwide salt pan were at safe levels. However, continuous management of heavy metal contamination, such as PVC met, is still necessary.

• Journal of the Korean Chemical Society
• /
• v.66 no.2
• /
• pp.75-77
• /
• 2022

• Korean Journal of Plant Tissue Culture
• /
• v.27 no.4
• /
• pp.325-337
• /
• 2000

All living organisms depend on soil and water for their sustained growth and development. In recent years, sustenance of life in these growth matrices has been adversely affected by the cumulative increase in environmental pollutants resulting from increasing population, growing economies and resource-use. This review provides a glimpse into the problem of global environmental pollution, the traditional technologies available for remediation and the scope of emerging‘plant-based remediation’technologies. Phytoremediation, the use of plants to effectively remove or stabilize contaminants from the growth substrate, is a low cost and ecologically friendly alternative to the common‘dig and dump’technologies. The field of phytoremediation has been driven by the intrinsic need for identification of ideal candidate plant species. To date, there are only a very few identified plants which satisfy all of the prerequisites for use in phytoremediation. The review focuses on one such plant species, the common horticultural plant scented geranium (Pelargonium sp.), with demonstrated potential to remediate metal / salt contaminated soils / aqueous systems. The characterization of tolerance and metal / salt accumulation potential of Pelargonium sp. and its efficacy in remediating complex contaminated sites are described. The unique ability of scented geraniums to tolerate excessive amounts of multi-metals, hydrocarbon and salt mixtures, and at the same time to accumulate significant amounts of metal and salt ions in the biomass, renders this plant species as one of the ideal candidates for remediation.

• Journal of the Korean Chemical Society
• /
• v.67 no.4
• /
• pp.222-225
• /
• 2023

Metallic salts of C10-18 aliphatic carboxylic acids were prepared and their scanning electron microscopic images were analyzed for the morphology dependency with the metal and the carboxylic acid. Regardless of metal ion, metal salts of dicarboxylic acids showed a high crystallinity with a fiber image (SuA-Na). The aromatic dicarboxylates also represented a morphology of a rectangular-rod or board shapes (IA-Li, IA-Ba). With Na ion, most aliphatic carboxylate (MA, PA, SA) showed a fiber-like crystallinity. However, other monovalent Li, K and multivalent Mg, especially Al ion resulted a glassy-amorphous in the metallic salts of acids (MA, PA, SA). With divalent Ba and Ca ions, the metal salt of aliphatic acids expressed a branched round cluster shape as in SA-Ca, SA-Ba. Both Li and Mg ions with a similar size showed a strong morphological similarity in the metallic salts of aliphatic acids MA, PA, SA. In the case of Na and Ca ions with a similar size (98, 106 pm), both ionic salts of stearic acid gave a branching effect for a fiber or round granular image. In the case of hydroxyl-aliphatic acids (HLA, HPA, HSA), the fiber images in HLA-Na and HSA-Na was appeared about 100 nm thicker than those of nonhydroxycarboxylates (LA-Na, SA-Na). The metallic salts of unsaturated C-18 carboxylic acids (OlA, LeA and LnA) showed an amorphous glassy image due to a kinked carbon chain.