• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.106-113
• /
• 1996

Using stainless steel as the cold forged parts especially the outer parts of automobile is gradually increasing because it can bear up against the erosion and the wear. During cold forging of the stainless steel the working pressure acting on die surface are very high therefore the wear on die surface can be greatly increased. In cold forging processes, die failure must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The die wear affects the tolerances of forged parts, metal flow and costs of processes etc. The only way to to control these failures is to develop methods which allow prediction of the die wear and which are suited to be used in the desing stage in order to optimize the process. In this paper, the rigid-plastic finite element method was combined with the wear prediction routine and then the forward extrusion process using stainless steel was analysed simultaneously. To minimize the die wear the FPS algorithm was applied and the optimal conditions of die configuration are suggested.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.203-216
• /
• 1990

The purpose of this study was to evaluate the cervical margin fitness in the collarless metal ceramic crowns formed by different techniques. Specimens were divided as follows : the metal ceramic crowns with metal butt margin as group I, the collarless metal ceramic crowns formed with resin binder technique as group II, and the collarless metal ceramic crowns formed with shoulder powder mixed with phosphate-bonded investment liquids on a refractory die as group III. Each group was made of five specimens, and their marginal fitness on each epoxy die was evaluated under scanning electron microscope of x200 magnification at three measuring points : mesial, central, distal. The following results were obtained. 1. The metal ceramic crowns with metal butt margin exhibited significantly better marginal fitness than the collarless metal ceramic crowns. The marginal fitness in descending order was group I, III, II. 2. The collarless metal ceramic crown formed with resin binder technique had the worst marginal fitness & showed cervical color variation and dermacation between the corrected porcelain & the dentin porcelain. 3. The collarless metal ceramic crowns formed with shoulder powder mixed with phosphate-bonded investment liquids on a refractory die exhibited significantly better marginal fitness & sharper marginal configuration than the other collarless group.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.37-41
• /
• 2012

Usually compound dies are used in clinch washer production. However, in this study, a fine blanking die is designed and manufactured, and clinch washers are produced by the die. Clinch washers are for electric exhaust gas recirculation (EEGR) and they recirculate some of exhaust gas to reduce harmful substances. Fine blanking automation production eliminates difficulties operators face on conventional press.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.61-64
• /
• 2003

In the field of automobile industry, suspension parts have been fabricated by the light metal part to substitute the steel part. For application light metal of suspension parts, mechanical property of high strength was performed. For anting semi-solid die casting of suspension part, die filling and solidification simulation have been carried out with Ostwald-de Waele rheological model. We designed the optimal die and secured injection condition as possible as laminar flow based on the result of computer simulation. Mechanical properties of knuckle part and heat treatment condition were investigated.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.1
• /
• pp.56-61
• /
• 2001

This work is concerned with the development of a new plaster die casting process the combines pressurization and vibration for the prototyping of die-castings, and also with a plaster die-casting machine that has a structure quite similar to that of an ordinary die casting machine. The machine utilized an air cylinder for pressurization and a magnetic actuator for vibration. A rapid prototyped pattern is made by the LOM process to prepare a plaster mold. In the process, a plunger int he developed machine simultaneously pressurizes and vibrates the molten metal to fill the plaster mold completely and to facilitate the creation of nuclei in the molten metal, respectively. The developed machine produced a prototype of an end clutch cover with a remarkable improvement in mechanical properties.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.146-154
• /
• 1996

In this work, rapid prototyping and three-dimensional finite element analysis are simultaneously applied to the die design of metal forming processes. Rapid prototyping is a new prototyping technology which produces three-dimensional part models directly from CAD data and has been extensively applied to various manufacturing processes. There are many types of rapid prototyping systems due to their building principles and materials. In this work, Stereolithography Apparatus(SLA), which is the most widely used rapidprototyping system, is introduced to manufacture the die set. For general preparation of STL file, which is the standard input file of rapid prototyping system, mesh data which are used in describing the die surface in finite element analysis are translated so that rapid prototyping and finite element analysis are dffectively connected. A die set for spider forging and a clover punch for deep drawing section are manufactured effciently using SLA prototypes, and metal forming experiments are carried out using them. Comparing the result of experiments with that of analyses, the processes can be predicted and designed successfully.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.24-28
• /
• 2016

In this study, relevant to impact extrusion process of the rectangular batter case for electric vehicles, numerical and experimental analyses were conducted to reduce the earring defects induced in the unevenness of metal flow. Since the earring is caused by the non-uniform metal flow induced in the friction and aspect ratio in the bottom section. As a way to reduce the earring, variable land die concept was applied. In order to analyze numerically the complex metal flow by using commercial finite element package, DEFORM 3D, impact extrusion process was simplified in upsetting mode at bottom section and extrusion mode at land section. The impact extrusion experiments were conducted to verify the assessment of process parameter for impact extrusion. As results, variable land die which has longer longitudinal section makes reduce earring defects. In addition, it was confirmed that the effect that slug shape like dog-bone also can reduce the earring. This study is expected to be able to present the useful design guidelines for manufacturing the battery case.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.1030-1033
• /
• 2002

In this study, it is important that we have an understanding of the metal flow for manufacturing condenser tube in porthole die extrusion, because this need to provide for household appliances market that is expected to grow into the major market of the cooling system hereafter. Condenser tube is mainly manufactured by conform exclusion. However, this method was not satisfied a series of the needs for manufacturing condenser tube as compared with porthole die extrusion. The deforming skill recently is required high-productivity, high-accuracy and reducing lead-time, thus it is essential to substitute conform exclusion by porthole die exclusion. Porthole die extrusion has many advantages such as improvement of productivity, reduction of production cost etc. In general, the porthole die extrusion process consists of three stages(dividing, welding and forming stages). In order to obtain the detailed mechanics, to assist in the design of proper die shapes and sizes, and to improve the quality of products, porthole die extrusion should be analyzed in as non-steady state as possible during the entire process to evaluate detailed metal flow, temperature distribution, welding pressure and extrusion lead, and therm stress analysis was practiced to obtain effective stress and elastic deformation value. A analytical results provide useful information the optimal design of the porthole die for condenser tube.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.1 no.1
• /
• pp.63-70
• /
• 2002

In the field of design and making tool for press working, the progressive die for very thick sheet metal(SS41, 4mm) is a specific division. In order to prevent the defects, the optimum design of the production part, Strip layout, die design, die making and tryout etc. are necessary. They require analysis of many kinds of important factors, i.e. theory and practice of metal working process and its phenomena, die structure, machining condition for die making, die materials, heat treatment of die component, know-how and so on. In this study, we designed and constructed a progressive die of multi stage and tried out through the I-DEAS, DEFORM, and CAD/CAM application. Out of these processes, the die development could be taken advanced technology. Especially the result of try out and its analysis become to the characteristic of this study.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.10a
• /
• pp.122-130
• /
• 1996

During the cold forming, due to high working pressure acting on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. Die wear affects the tolerances of formed parts, metal flow and costs of process etc. The only way to control these failures is to develop methods which allow prediction of die wear and costs of process etc. The only way to control these failures is to develop methods which allow prediction of die wear and which are suited to be used in the design state in order to optimize the process. In this paper, the wear experiments to abtain the wear coefficients and the upsetting processes was accomplished to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes was accomplished to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes was accomplished by the rigid-plastic finite element method. The result from the deformation analysis was used to analyse the die wear during the processes and the predicted die wear profiles were compared with the measured die wear profiles.