• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.97-98
• /
• 2006

Gas-permeable metal die materials are developed using tool steel powder, packed in a mold having the insertion of orthogonally arrayed polymer wires. Linear gas-permeable channels in orthogonal array are thus developed by the burning out of the polymer wires, which yield a microstructure with wear resistance value and air permeability much larger than those of the conventional gas-permeable die material.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.39-43
• /
• 2016

Most of automobile parts manufactured through sheet metal forming are mass-produced by using press mold. In recent years, automation and speeding up of press lines have been expanding to maximize product productivity using a press die. The proportion of the moving time in the press line is high, and therefore requires high-speed and automated equipment for the moving process. In this paper, to provide the double-moving system can be the moving time reduction and increased productivity. Developed transport system consists of the material supply, the material feeding device and the PLC controller and the devices are positioned between each of the pressing process. In this paper, the double-moving system including developed units using a multi-axial single-acting through this reduced the C/T(cycle time) and improved the productivity.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.7
• /
• pp.70-75
• /
• 2004

The shearing process for the sheet metal is normally used in the precision elements such as a lead frame of IC chips. In these precision elements, the burr formation brings a bad effect on the system assembly and demands the additional deburring process. In this paper, we developed the small size precision punching system to investigate burr formation mechanism and to present kinematically punch-die aligning methodology between the rectangular shaped punch and die. The punch is driven by an air cylinder and the sheet metal is moving on the X-Y table system which is driven by two stepping motors. The whole system is controlled by microprocessor and is communicated with each other by RS232C serial communication protocol. Punching results are measured manually using the SEM photographs and are compared aligning result with miss aligning one.

• Transactions of Materials Processing
• /
• v.7 no.3
• /
• pp.246-259
• /
• 1998

This paper describes a research work of developing a computer-aided design and manufacturing of irregular shaped sheet metal product for blanking or piercing and bending operations. An approach to the system is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories experimental results and the empirical knowledge of field experts, This system has been written in AutoLISp on the AutoCAD and in customer tool kit on the SmartCAM with a personal computer and is composed of nine modules which are input and shape treatment, flat pattern-layout, pro-processor module. Based on the knowledge-based rules, the system is designed by considering several factors, such as material and thickness of product complexities of blank geometry and punch profile sheet metal to give flat pattern and automatically account for the adjustment of bending allowances to match tooling requirements by checking dimensions and generating NC data automatically according to drawings of die-layout module. Results carried out in each module will provide efficiencies to the designer and the manufacturer of blanking or piercing and bending die in this field.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.12
• /
• pp.1093-1100
• /
• 2014

The goal of this paper is to investigate preliminary the applicability of 3D printing technologies for the development of the hot bulk forming process and die. 3D printing technology based on the plastic material was applied to the preform design of the hot forging process. Plastic hot forging dies were fabricated by Polyjet process for the physical simulation of the workpiece deformation. The feasibility of application of Laser-aided Direct Metal Rapid Tooling (DMT) process to the fabrication of the hot bulk metal forming die was investigated. The SKD61 hot-working tool steel was deposited on the heat treated SKD61 using the DMT process. Fundamental characteristics of SKD 61 hot-working tool steel deposited specimen were examined via hardness and wear experiments as well as the observation of the morphology. Using the results of the examination of fundamental characteristics, the applicability of the DMT process to manufacture hot bulk forming die was discussed.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.924-928
• /
• 2018

The objective of this study is to solve a problem that is occurred during the spline machining of tubular shaft yoke in both side IMS module. In order to simulate the problem, the movement direction of upper die was set as standard case and error case. The material of tubular shaft yoke was set to S20C as refer to the analysis library. The movement directions of upper die were separated with standard case and error case. The error case was set to simulate the problem in the spline machining of tubular shaft yoke. In order to solve the problem, the outer radius of upper die were modelled from 9.40mm to 9.44mm. The simulation results were analyzed and compared in terms of effective stress, metal flow line and folding phenomena characteristics. In case of the outer radius of upper die was 9.42mm, it was observed a relatively uniform effective stress distribution and had a straight metal flow line.

• Transactions of Materials Processing
• /
• v.23 no.2
• /
• pp.75-81
• /
• 2014

Progressive dies are used for metal stamping during which multiple operations are performed in a sequence. Material is fed automatically from a coil into the press and advances from one die station to the next with each press stroke. Transfer dies are used in high-volume manufacturing for round, deep-drawn, and medium-to-large parts. Several different operations may be incorporated within a transfer die such as blanking, bending, piercing, trimming, and deep drawing. The main challenge in the current study is how to deform a seat cushion panel meeting the design specifications without any defects. A complex automation die manufacturing technology for the automotive seat cushion panel, mixing both semi-progressive die and transfer die for continuous production, was developed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.88-93
• /
• 1998

The service life of tools in metal forming process is to a large extent limited by wear, fatigue fracture and plastic deformation. In warm forging processes wear is the predominant factor for operating lives of tools. To predict tool life by wear, Archard's wear model is generally applied. Usually hardness of die is considered to be a function of temperature in Archard's wear model. But hardness of die is a function of not only temperature but also operating time of die. To consider softening of die by repeated operations, it is necessary to express hardness of dies by a function of temperatures and operating time. By experiment of reheating of dies, die softening curves were obtained. Finally modified Archard's wear model in which hardness of die was expressed as a function of main tempering curve was proposed.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.586-593
• /
• 1998

In recent automotive industries there has been significant increase in applications of computer simulation to the manufacturing of stamping dies for inner and outer body panels which greatly affect durability and aesthetic quality of automobiles. Enhancement of die quality and reduction of total die manufacturing time and consequently manufacturing cost are the visible outcome. However to successfully apply the result of simulation by a commercial package to the die manufacturing development of an optimal die manufacturing process is required upon the completion of analysis of forte and shortcoming of available sheet metal forming softwares. Based on the results of numerical analysis of front door outer panel forming. this paper evaluates the applicability of simulation results to the real die manufacturing for automotive body panels. Also it attempts to select an optimal die manufacturing process including design machining and tryout. Lastly it discusses the expected effects by adopt-ing the selected process in a real stamping die manufacturing facility.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.385-388
• /
• 2001

In part forming process of metal matrix composites, the die casting and squeeze casting process are limited the size and dimension in term of final parts without machining. The thixoforming process for metal matrix composites has numerous advantages compared to die casting squeeze casting and compocasting. However, for the thixoforming process, the billet with the desired volume fraction must be heated to obtain a uniform temperature distribution over the entire cross-sectional areas. To obtain the reheating conditions of composites, the particulate reinforced metal matrix composites for thixoforming were fabricated by combined stirring process which is simultaneously performed with electro-magnetic stirring and mechanical stirring process.