• 소성∙가공
• /
• 제20권8호
• /
• pp.575-580
• /
• 2011

Direct laser melting(DLM) is promising as a joining method for producing parts for automobiles, aerospace, marine and medical applications. An advantageous characteristic of DLM is that it affects the parent metal very little. The mechanical properties of parts made by DLM are strongly affected by the porosity and surface roughness of the laser melted beads. This is a systematic study of the effects of the porosity and surface roughness of laser melted beads using various processing parameters, such as laser power, scan rate and overlapping ratio of the fill spacing. The specimens were fabricated with 316L and 304L austenitic stainless steel powder. Dense parts with low porosity were obtained at low laser scan speed, as it increased the aspect ratio of the parental material and the depth of penetration. The variations of surface roughness were examined at various processing parameters such as overlapping ratio and laser power.

• 한국축산식품학회:학술대회논문집
• /
• 한국축산식품학회 2006년도 정기총회 및 제37차 춘계 국제학술발표대회
• /
• pp.94-97
• /
• 2006

Proteolytic enzymes and ginger extract were effective on tenderising M. pectoralis profundus, resulting in higher collagen solubility, a decrease of melting denaturation temperature and WBSF compared with the control. Comparing all treatments, bromelain treatment showed to be higher for collagen solubility than other treatments, but no significant differences in onset and melting denaturation temperature of intramuscular connective tissue were found. These corresponded to WBSF results. The present study indicates that ginger extract might be effectively able to be utilised in pilot level as better alternatives to bromelain and papain for tenderisation of tough meat, such as cull cow and beef cuts with many collagen.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.193-198
• /
• 2005

The present experiments have been performed for obtaining the melting heat transfer characteristics of micro-encapsulated solid-liquid phase change material and water mixed slurry flow in a circular tube heated with constant wall heat flux. The phase change material having a low melting point was selected for a domestic cooling system in the present study. The governing parameters were found to be latent heat material concentration, heat flux, and the slurry velocity. The experimental results revealed that the increase of tube wall temperature of latent microcapsule slurry was lower than that of water caused by the heat absorption of fusion.

• 대한수의학회지
• /
• 제26권2호
• /
• pp.225-228
• /
• 1986

Progesterone immunogen has been synthesized and its melting point, Rf-value, UV and IR spectrum have been measured to develope the essential step in antisera production against low molecular weight substance. Mixed anhydride reaction was used to conjugate $11{\alpha}$-hydroxy-progesterone with succinic anhydride. Melting point of one intermediate compound was $156^{\circ}C$, and Rf-value was 0.41 in benzene : acetone : methanol (5 : 5 : 2). Maximum absorbance was measured at 242nm and ${\varepsilon}$ was $1.641{\times}10^4cm^2/mole$. Loss of hydroxy group was observed at 3450nm, and carbonyl group was appeared at 1160nm, 1250nm and 2960nm. These results indicated that the intermediate compound was progesterone hemisuccinate. Maximum absorbance of progesterone bovine-serum albumin(BSA) conjugate was observed at 250nm. Molar ratio of progesterone to BSA was average 15.4 on UV spectrum.

• 한국표면공학회지
• /
• 제49권6호
• /
• pp.549-554
• /
• 2016

Low melting metals are difficult to weld because it is vaporized. But epoxy resin make bonding possible using low melting material and dismissal materials. This study is to improve the bonding strength of epoxy and substrate by mechanical and electrochemical methods. In case of mechanical work, bonding strength is 17.6MPa and in case of pre-work, bonding strength is 15.3MPa. When anodizing and mechanical work is applied, bonding strength is 25.3Mpa is increased 165%. When anodizing is applied, bonding strength is 27.6Mpa.

• 한국식품영양과학회지
• /
• 제27권1호
• /
• pp.35-37
• /
• 1998

This study was performed to investigate lipid content, melting point, refractive index, fatty acid composition and energy intake from lipid of commercial fried instant noodles. Sixty five samples were collected in Seoul area, and analyzed. The average of lipid content was 16.7%, melting point and refractive index were 29$^{\circ}C$ and 1.46, respectively. The fatty acid composition mainly consisted of C16:0, C18:1 and C18:2. The ratio of P/M/S in fried instant noodles was 0.19 : 0.77 : 1.00. The average energy intake from lipid of 100g fried instant noodles was 150.3kcal.

• 한국세라믹학회지
• /
• 제44권11호
• /
• pp.618-621
• /
• 2007

In this study, flint glass batches with blast furnace slag (BFS) were prepared and the contribution of the BFS to the fining of melts was studied through investigations of the melting and fining characteristics. Additionally, a sulfur redox reaction for BFS-doped melts was examined by square wave voltammetry (SWV). The results of the melting & fining test showed that BFS improved the fining of the melts. In a voltammogram of BFS-doped melts, two reduction peaks were shown at high frequencies while only one peak appeared at low frequencies. The peaks were located at a potential that was similar to those of melts fined by sulfate. From those results it was concluded that sulfide ($S^{2-}$) in BFS has effects in glass melts that are identical to those of sulfate ($SO_4^{2-}$).

• 한국식품영양과학회지
• /
• 제23권2호
• /
• pp.303-307
• /
• 1994

This study was carried out to investigate lipid content, melting point, refractive index and fatty acid composition of commercial chocolate and imitation chocolate. Fifty-eight samples for test were 45 of domestics and 13 of foreign in Seoul. The results were as follows ; Mean value of lipid content was 35.1% in chocolate and 31.9% in imitation chocolate, and foreigns were lower than domestics. In melting point of lipid, chocolates and imitation chocolate were 26.4$^{\circ}C$ and 27.4$^{\circ}C$ as mean value, respectively. Mean value of refractive index of lipid was 1.4560, imitation chocolate of domestic were lower than another. The fatty acid compositions were chiefly consisted of {{{{C_18:1 , C_18 , C_16, C_16:1 and C_18:2. }} The ratio of SFA : MUFA : PUFA in chocolate and limitation chocolate were 8.2 :6.9 :1.0 and 3.1 : 4.3: 1.0 , respectively.

• 한국분말재료학회지
• /
• 제8권1호
• /
• pp.20-25
• /
• 2001

Most of mold manufacturing procedures have been automated by the introduction of NC machine tool and CAD/CAM system. But the three-dimensional surface curvature of the mold must be done by hand work of well-skilled workers. Magnetic abrasive polishing powders were investigated for surface polishing for 3D curvature. This study aims to investigate homogeneously distributed hard phase in Fe matrix and strong bonding between Fe-matrix and hard phase. The NbC powder, $B_4C$ powder and $Al_2O_3$ powder were mixed in Fe-matrix respectively. Mixed Fe-hard phase powders were compacted by press and then these were melted by plasma melting. According to SEM, XRD and OM observation, Fe-NbC magnetic abrsive powder had the most homogeneous distribution and strong bonding. As a result of magnetic polishing, the surface roughness before magnetic polishing, 1 ${\mu}m$ $R_{max}$, was reduced to 0.2 ${\mu}m$ $R_{max}$ over the entire inner surface of the tube.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1996년도 춘계학술대회
• /
• pp.130-132
• /
• 1996

It is well known when porous calcium phosphate ceramics are used as a bone graft substitute, new tissues or blood vessels are grown into the porous implant due to their excellent biocompatibility. In this study, the ${\beta}$-crystalline form of calcium metaphosphate, $Ca(PO_{3})_{2}$ is prepared by the controlled thermolysis of monocalcium phosphate, $Ca(H_{2}PO_{4})_{2}$. The diameter of cylindrical pores formed during cooling was controlled by a holding time at the melting point of a monocalcium phosphate and by the change of a recrystallization temperature, to obtained the most appropriate size (about $200{\mu}m$) of pores. It was observed that the increasing holding time at the melting point of monocalcium phosphate results in the decreases of pore sizes.