• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.168-174
• /
• 2006

A pilot scale (200kg/hr) pyrolysis melting incineration system is designed and constructed in Korea Institute of Industrial Technology. The incineration process is composed of pyrolysis, gas combustion, ash melting, gas stabilization, waste heating boiler, and bag filter. For each unit process, experimental approaches have been conducted to find optimal design and operating conditions. Especially, a pyrolysis is very important process in that it is a way of energy recirculation and minimizing the waste products. This paper presents major results of the most efficient operating conditions in a pilot scale pyrolysis melting incinerator.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.791-797
• /
• 2002

This paper introduces the partial melting process for solder application and characterization of its feasibility using Sn-Ag, and Sn-Cu solder alloys. ill order to show that the liquid phase in the semi-liquid state maintains the similar wettability as single-phase liquid, the wetting balance tests are conducted with varying temperatures and compositions. Also, as a new soldering technology, the microstructural and mechanical test were investigated. The results from this research indicate that the partial melting can yield satisfactory sider joints as long as the liquid phase acquires sufficient chemical activity. At a condition where the partial melting is effective, a direct correlation between the wettability and the surface tension is found to exist.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.9
• /
• pp.1775-1777
• /
• 2009

BiSrCaCuO films were prepared on MgO single substerate at $885^{\circ}C$ by melt process. The films showed superconductivity above liquid nitrogen temperature (Tc= 96K). To investigate the effect of a melting temperature on the forming of the surface texturing, the samples were prepared under various temperature. The used powder was of high Tc phase. It is implies that the origin of the properties due to the heat treatment.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.11
• /
• pp.1106-1113
• /
• 2001

This paper presents experimental works on the ultrasonic influence during melting of ice and paraffin and compared the paraffin's result with ice's results. The experiments was carried out under two setting conditions.: 1) Heater without ultrasonic vibration, 2) heater with ultrasonic vibration. Experimental observations show that the ultrasonic vibration enhances significantly the phase-change process (melting) so that the melting time is reduced about 16∼25% compared to those of molting process without ultrasonics in the melting of both ice and paraffin. But the influence of ultrasonics was not significant to affect the reduction of the power consumption. In the case of paraffin, the reduction rate of power consumption was about 20%, but the reduction of the power consumption was increased about 0∼12%.

• Transactions of Materials Processing
• /
• v.20 no.2
• /
• pp.118-123
• /
• 2011

Manufacturing of the bipolar plate of a direct methanol fuel cell (DMFC) by direct laser melting technology (DLM) was attempted. The DLM technology is highly influenced by process parameters such as laser power, scan rate and layering height. Therefore, an analysis of the DLM technology was performed under various conditions. The bipolar plates were fabricated using the DLM process with 316L stainless steel (STS 316L) plates and powder. Powder melting trials at various energy density were performed in order to select a feasible melting range for a given laser power. The melting line height increases and eventually saturates when the energy density increases, but decreases when the laser power increases at a given energy density. For the estimation of the potential performance of the bipolar plate, the surface roughness and contact resistance of the DLM layer were also analyzed. The changes of line height and thickness are useful information to report when manufacturing bipolar plate of fuel cell through the DLM process.

• Journal of the Korean Society of Visualization
• /
• v.22 no.1
• /
• pp.6-17
• /
• 2024

This study examined the natural convection heat flow characteristics of the melting process of PCM (palm oil) inside a liquid flexitank(bag) for a cargo container. A film heating element was installed on the bottom of the container, and numerical analysis was performed under heat flux conditions of 1,000 to 4,000 W/m². As a result, the melt interface of the PCM rises to a nearly horizontal state over time. In the initial stage, conduction heat transfer dominates, but gradually waves at the cell flow and melt interfaces are formed due to natural convection heat transfer. As melting progresses, the Ra number increases parabolically, and the Nu number increases linearly and has a constant value. The Nu number rises slowly under low heat flux conditions, whereas under high heat flux conditions, the Nu number rises rapidly. As the heat flux increases, the internal temperature oscillation of the liquid phase after melting increases. However, under high heat flux conditions, excess heat exceeding the latent heat is generated, and the temperature of the molten liquid is raised, so the increase in melting rate decreases. Therefore, the appropriate heating element specification applied to a 20-ton palm oil container is 2,000 W/m².

• Transactions of Materials Processing
• /
• v.19 no.8
• /
• pp.517-522
• /
• 2010

Selective laser melting (SLM) is emerged as a new manufacturing technique to directly fabricate precise parts using metallic materials. The final characteristics of a component fabricated through the SLM process are strongly dependent upon various parameters such as laser power, scan rate and pulse duration, etc. This paper, therefore, focuses on the dimensional characteristics of melted $20{\mu}m$ Fe-Cr-Ni powder by fiber laser for the selective laser melting process. With energy density decrease, the height and depth were decreased. Although the conditions are of the same energy density, the shape is different by laser power and scan rate. The shapes at various laser parameters were divided into 3 groups based on depth over height. The smooth regular shape is obtained under the conditions of $50{\mu}m$ of powder height and $15-20{\mu}s$ of pulse duration. And the laser power influenced the variation of shape more significantly than the scan rate.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.585-589
• /
• 2009

Extruder is divided to greatly three part at extrusion process. First, by hopper(Hopper) second, barrel(Barrel) with Screw that is point of extruder and third that is raw material supply wealth extrusion into dies(DIES) Part that decide shape of do product greatly divide. Hopper is role that distribute in raw material supply wealth (Feeding zone) of Screw preserving raw material in state of high quality how at extrusion process, and make distributed raw material as Screw in barrel rotates and 3 stage and inflicting heat and pressure raw material melting(Melting) state. And raw material of melting state Screw's measuring stoker(Metering zone) whereabouts anaphora do and product is completed through pipe channel of dies. Dies that is the most important as Screw in extrusion is part that is last part of melting state process of raw material and causes huge effect in quality of product. If more than design of dies happens, manufacture itself of dies is hard, but there are a lot of amount of losses accordingly. In this research, make pipe channel that raw material of melting state flows in dies can present dies basic design method through flow analysis of ideal pipe channel using CFdesign.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.151-155
• /
• 2006

The large amount of energy is consumed in a process for keeping the high temperature melting pool. For this reason, in addition to the wastes input to keep the high temperature melting pool, it is necessary for an auxiliary fuel and LOx to throw into the melting pool. So in this study, using a new melting furnace system, the experiments to keep the melting pool with minimal energy without throwing an auxiliary fuel and LOx was carried out. Also it is hoped that the results of the experiment will be available to analyze keeping a melting pool and behavior in a melting furnace.

• Journal of Korea Foundry Society
• /
• v.17 no.6
• /
• pp.598-607
• /
• 1997

Fractional melting process involves heating an alloy within its liquid-solid region simultaneously ejecting liquid from the solid-liquid mixture. The extent of the purification obtained is comparable to that obtained in multi-pass zone refining. The new fractional melting process in which centrifugal force was used for separating the liquid from the mixture has been developed and applied to the purification of the metallic grade. Refining ratio depends on partition ratio, cake wetness and diffusion in the solid, and it was controlled by various processing parameters such as rotating speed and heating rate. The new parameter called "refining partition coefficient" has been suggested to estimate the effects of processing variables on the refining ratio. Because major impurities in MG-silicon such as Fe, Al, Ni have a low segregation coefficient, good purification effect is expected. The results of refining MG-silicon(98%) showed that 3N-Si was obtained in refined solid of 50% of the original sample.