• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.477-478
• /
• 2006

Close-coupled atomizers are of great interest and controlling their performance parameters is critical for metal powder producing and spray forming industries. In this study, designed close-coupled nozzle systems were used to investigate the effect of the nozzle types and protrusion length of the melt delivery tube on the pressure formation at the melt delivery tube tip. The observed metal flow rate was not behaving as what was earlier assumed, namely that, deeper aspiration enhanced metal flow rate. Higher aspiration pressure at the tip of the melt delivery tube increases the stability of atomization process.

• Korean Journal of Metals and Materials
• /
• v.47 no.11
• /
• pp.734-739
• /
• 2009

It is well known that the temperature and the flow pattern of the crystal-melt interface affect the qualities of the single crystal in the Czochralski process. Thus the temperature profile in the growth system is very important information. This work focuses on controlling the temperature of the silicon melt with a thermal gradient of the crucible. Therefore, the side heater is divided into three parts and an extra heater is added at the bottom for thermal gradient. The temperature of the silicon melt can be strongly influenced and controlled by the electric power of each heater.

• Fibers and Polymers
• /
• v.4 no.3
• /
• pp.107-113
• /
• 2003

The branched polypropylene (b-PP) was prepared by melt blending process with initiator, antioxidant, and functional monomers to improve the melt strength through the melt grafting. The melt flow index (MFI) of the b-PP was increased with increasing the initiator content. On the introduction of the alkylamine as the branching agents the MFI of the b-PP was increased, while that of the b-PP with the pentaerythritol triacrylate (PT) was decreased. It may be caused by the chain scission of the i-PP backbone due to the reduced thermal stability of the i-PP on the melt blending. The MFI of the b-PP without the antioxidant was increased due to the chain scission occurred during the melt processing, while on the introduction of the antioxidant, the MFI of the b-PP was decreased. The crystallization temperature of the b-PP was higher than that of PP, which was attributed to the branched chain structure. It was found that the PT was the most effective functional monomers for enhancing the melt properties of the b-PP.

• Korea-Australia Rheology Journal
• /
• v.20 no.2
• /
• pp.79-88
• /
• 2008

In this study, we focus on the improvement of the filling efficiency in injection molding by application of ultrasonic vibration. While studies about the filling efficiency of typical filling processes in the injection molding have been widely performed, there have been only few studies about the filling efficiency of an ultrasonic process. The effect of the ultrasonic vibration is an important process condition, which influences the flow characteristics of polymer melt. This new condition even affects well-known injection conditions such as cavity pressure, injection temperature and mold temperature. For this study, we carried out a numerical analysis by appropriate modeling and analysis of the ultrasonic process in the filling process. To verify this numerical analysis, we compared the numerical results with the experimental data. Also, we analyzed the filling process in a thin cavity using this numerical analysis. To understand the flow characteristics of polymer melt in the ultrasonic process, we substituted real and complex vibration conditions with simplified and classified conditions according to the position of vibrating cavity surfaces and the phase difference between two opposing cavity surfaces. We also introduced MFR (melt flow ratio) as a new index to estimate the filling efficiency in the ultrasonic process.

• Journal of Mechanical Science and Technology
• /
• v.16 no.1
• /
• pp.94-101
• /
• 2002

Convection-dominated melting in a rectangular cavity is analyzed numerically with particular attention to the multi-cellular flows in the melt. At the earlier stage of the melting, the melt region is quite similar to a cavity with high aspect rati71, where the multi-cellular natural convection appears. Numerical results show that the formation and evolution of the multiple flow cells in the melt region is approximately similar to t]tat of a single-phase flow in a tall cavity with the same aspect ratio; however, the continuous change of the melt region due to the melting affects the detailed process. Also, numerical aspects for the prediction of the detailed flow structure in the melt are discussed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.1
• /
• pp.5-14
• /
• 2003

Principles of a novel pulse growing method are described. The method realized in the crystal growing on a seed from melts under raw melt feeding provided a more reliable control of the crystallization process when producing large alkali halide crystals. The slow natural convection of the melt in the crucible at a constant melt level is intensified by rotating the crucible, while the crystal rotation favors a more symmetrical distribution of thermal stresses over the crystal cross-section. Optimum rotation parameters for the crucible and crystal have been determined. The spatial position oi the solid/liquid phase interface relatively to the melt surface, heaters and the crucible elements are considered. Basing on that consideration, a novel criterion is stated, that is, the immersion extent of the crystallization front (CF) convex toward the melt. When the crystal grows at a <> CF immersion, the raised CF may tear off from the melt partially or completely due to its weight. This results in avoid formation in the crystal. Experimental data on the radial crystal growth speed are discussed. This speed defines the formation of a gas phase layer at the crystal surface. The layer thickness il a function of time a temperature at specific values of pressure in the furnace and the free melt surface dimensions in the gap between the crystal and crucible wall. Analytical expressions have been derived for the impurity component mass transfer at the steady-state growth stage describing two independent processes, the impurity mass transfer along the <> path and its transit along the <> one. The heater (and thus the melt) temperature variation is inherent in any control system. It has been shown that when random temperature changes occur causing its lowering at a rate exceeding $0.5^{\circ}C/min$, a kind of the CF decoration by foreign impurities or by gas bubbles takes place. Short-term temperature changes at one heater or both result in local (i.e., at the front) redistribution of the preset axial growth speed.

• Elastomers and Composites
• /
• v.22 no.3
• /
• pp.213-218
• /
• 1987

In this study, the rheological properties of a partially valcanized black filled EPDM were investigated as a function of degree of crosslinks using capillary rheometer. In order to obtain the samples having various degree of crosslinks between 0 and 6 percent, the vulcanization kinetics was also studied by Monsanto rheometer. The results showed that the die swell ana the pressure drop at the capillary entrance and exit increase nearly linearly with the increase in degree of crosslinks. However, melt fracture occurred at a lower shear rate for the samples of higher degree of crosslinks. These results were discussed in terms of the melt elasticity produced at the entrance region of capillary by the partial vulcanization. It is also interesting to note that the fluctuation of die swell during the practical extrusion or calendering process in the factories can be caused by the partial vulcanization occurred during the process.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.111-115
• /
• 1998

Fiber spinning is a continuous deformation process by which material is converted into a fiber. The melt spinning process was analyzed mainly by employing an asymptotic method of the so-called thin filament equations which formulates dynamics of spinning process by averaging over the cross-section of filament the set of fundamental equations. The method gives the approximate results for commonly used circular fiber spinning.(omitted)

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.232-233
• /
• 2002

Nanostructed high energy Nd-Fe-B based bulk magnet can be prepared by hot-working process (hot press and die-upset) from melt-spun amorphous or nanocrystalline powder.[1] Recently, we have investigated a modified method, current-applied pressure-assisted (CAPA) process, to produce nanocrystalline isotropic and anisotropic NdFeB magnets. The process consists of current-applied pressing the melt-spun powders to obtain isotropic precursor subsequent current-applied deforming the precursor to obtain textured magnet.[2-3] (omitted)

• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.382-389
• /
• 2008

To manufacture Al MMCs, in-situ melt mixing process is used because it is free from contamination, and it makes reinforcements homogeneously dispersed. Large eddy simulation method is used to find the optimum melt mixing condition. At the Re 3000, the most suitable mixing is occurred between Al-Ti and Al- B melts. The in-situ formed $TiB_2$ particles has the size varying from 40 nm to 130 nm, due to the increase of cooling rate, and exhibits a homogeneous dispersion. And the interface between reinforcement and matrix is clean. Both hardness and Young's modulus of this composite are improved with increasing the cooling rate.