• Journal of the Korean Wood Science and Technology
• /
• 제47권5호
• /
• pp.579-586
• /
• 2019

This work examined effects of the synthesis method and melamine content of melamine-urea-formaldehyde (MUF) resins on the bond-line features (i.e. resin penetration and bond-line thickness) in plywood. Two synthesis methods (MUF-A and MUF-B) and three melamine contents (5, 10, and 20%) were employed to prepare MUF resins. The MUF-A resins at three melamine contents were prepared by a simultaneous reaction of melamine, urea, and formaldehyde, while the MFU-B resins were prepared by reacting melamine at the same levels with formaldehyde followed by urea. The results showed that higher melamine content increased the viscosity of MUF-A and MUF-B resins. The resin penetration of MUF-A resins decreased by 48% while those of MUF-B resins increased by 16% at 20% melamine content. As a result, the MUF-A resins had greater bond-line thickness than those of MUF-B resins as the melamine content increased. The MUF-B resins resulted in thinner bond-line and greater resin penetration compared to those of MUF-A resins. The results suggested that MUF-B resins prepared with 20% melamine content had a proper combination of resin penetration and bond-line thickness that could produce plywood panel with a better adhesion performance.

• 한국가구학회지
• /
• 제20권3호
• /
• pp.247-252
• /
• 2009

The objective of this study was the dimensional stabilization of Korean red pine (Pinus densiflora) wood by the water-based thermosetting resin. A commercial melamine-formaldehyde resin was impregnated into wood samples and cured. The weight and dimensional change of woods treated by the resin, and the absorption and dimensional behavior of treated woods were investigated. The melamine-formaldehyde resin treatment improved significantly the dimensional stability of pine wood and showed about 40% of antiswelling efficiency. The mechanism of dimensional stabilization was interpreted as the complicated reason, such as bulking effect by the resin in cell wall, mechanical restraint and/or blocking of hygroscopic site by the resin in lumen.

• Journal of the Korean Wood Science and Technology
• /
• 제45권4호
• /
• pp.409-418
• /
• 2017

This work attempted to manufacture glued-laminated timber (Glulam) bonded with melamine-urea-formaldehyde (MUF) resin adhesives at various melamine contents from 20% to 50% under high frequency (HF) heating for a very short time. Two preparation methods were employed to prepare MUF resin adhesives with different melamine contents: one-batch method of synthesizing MUF resins in a single batch, and two-batch method of mixing urea-formaldehyde (UF) resin with melamine-formaldehyde (MF) resin that had been synthesized separately. As the melamine content increased, the gelation time and peak temperature of MUF resins decreased. The adhesion performance of plywood showed that the one-batch MUF resin adhesive with 50% melamine content only satisfied the standard requirement of water resistance. Thus, the one-batch MUF resin adhesive with 50% melamine content was applied for bonding wood lamina from four softwood species such as Japanese larch, Korean red pine, Korean pine and Japanese cedar to manufacture Glulam under HF heating. All Glulam samples bonded with the one-batch MUF resin adhesives with 50% melamine content except those from Korean Red Pine satisfied the requirement in water soaking or boiling water delamination test as an exterior grade Glulam. The presence of rosin in Korean Red Pine was believed to be responsible for its poor adhesion. These results showed that the one-batch MUF resin adhesives with 50% melamine content provided acceptable water resistance with exterior grade Glulam manufactured under HF heating.

• Journal of the Korean Wood Science and Technology
• /
• 제27권1호
• /
• pp.72-78
• /
• 1999

요소 멜라민수지의 조성에 의한 속경화의 가능성, 경화촉진제의 첨가에 의한 경화촉진 효과 및 접착성능에 대하여 검토하였다. 수지조성과 동시반응에 의해 제조한 UMF 수지의 겔화성과의 관계는 요소(멜라민/요소 몰비=0.2)에 대한 포롬알데히드의 몰비가 증가할수록 겔화시간이 빨라졌다. 그러나, 요소에 대한 포름알데히드의 몰비가 2.5이상에서는 수지중의 유리포름알데히드량이 KS기준에 합격하지 못하므로 속경화를 위해 수지 합성시 포름알데히드의 첨가량을 높이는 것은 어려울 것으로 생각된다. 또한, 요소에 대한 포름알데히드의 몰비를 3.4로 고정한 UMF수지에 있어서 요소에 대한 멜라민의 몰비가 0.3에서 0.6으로 증가할 수록 수지의 겔화시간은 다소 단축되었으나, 0.6이상에서는 다시 증가하였다. UMF수지의 겔화성과 접착강도는 경화제로서 염화암모늄과 p-툴루맨설폰산, 증량제로서 소액분과 콘글루텐의 병용에 의해 크게 향상되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제33권2호통권130호
• /
• pp.29-39
• /
• 2005

Formaldehyde emissions from wood-based panels bonded with pine and wattle tannin-based adhesives, urea-formaldehyde resin (UF), melamine-formaldehyde resin (MF), and co-polycondensed resin of urea-melamine-formaldehyde (UMF) were measured by the Japanese standard method using a desiccator (JIS A 1460) and the EN 120 (European Committee For Standardization, 1991) method using the perforator value. In formaldehyde emission, all particleboards made using the wattle tannin-based adhesive with three different hardeners, paraformaldehyde, hexamethylenetetramine, and tris(hydroxyl)nitromethan (TN), satisfied the requirements of grade $E_1$. But only those made using the pine tannin-based adhesive with the hexamine as hardener met the grade $E_1$ requirements. Hexamine was effective in reducing formaldehyde emission in tannin-based adhesives when used as the hardener. While the UF resin showed a desiccator value of $7.1mg/{\ell}$ and a perforator value of 12.1 mg/100 g, the MF resin exhibited a desiccator value of $0.6mg/{\ell}$ and a perforator value of 2.9 mg/100 g. According to the Japanese Industrial Standard and the European Standard, the formaldehyde emission level of the MDF panels made with UF resin in this study came under grade $E_2$. The formaldehyde emission level was dramatically reduced by the addition of MF resin. The desiccator and perforator methods produced proportionally equivalent results. Gas chromatography, a more sensitive and advanced method, was also used. The samples for gas chromatography were gathered during the experiment involving the perforator method. The formaldehyde contents measured by gas chromatography were directly proportional to the perforator values.

• 한국의류학회지
• /
• 제2권1호
• /
• pp.125-131
• /
• 1978

This study was intended to clarify (1) the release of free formaldehyde (2) transfer of free formaldehyde to the contacted fabrics during storing, and (3) the removal effect of free formaldehyde by washing from resin finished fabrics. The results of this study were as follow; 1. The decrease rate of free formaldehyde content in fabrics was higher during storing in open air, poly bag, and glass tube in descending order and the content of free formaldehyde in fabrics was decreased in glyoxal resin finished but, increased in Melamine M-3 resin finished when the fabrics was stored in polybag and in glass tube. 2. Increased amount of formaldehyde transfer to contacted fabrics was noted with Melamine M-3 resin finished than that of glyoxal resin finished. Increased amount of formaldehyde transfer as well as more free formaldehyde were noted in cotton fabrics than in polyester/ cotton blend. 3. The effect of removing free formaldehyde from the fabrics was better in case of solid alkaline soap, synthetic alkaline powdered detergents, neutral detergents in descending order. The romoval of free formaldehyde was marked after the 1st washing and almost no increase in free formaldehyde was found after three times of washing. 4. After first washing, the content of formaldehyde in Melamine M-3 resin finished fabrics increased more rapidly than that of glyoxal resin finished fabrics in condition of closed storing.

• 접착 및 계면
• /
• 제10권2호
• /
• pp.84-89
• /
• 2009

The objective of this research was to investigate the curing behavior and adhesion performance of urea-melamine-formaldehyde (UMF) resin for the four types of UMF-1, UMF-2, UMF-3, and UMF-4 which synthesized by the staged addition of melamine. Also, various network structures of these resin types were discussed based on their different curing behavior and adhesion performance. The curing behavior was evaluated by DMTA and thermal stability was checked by TGA. Adhesion performance was evaluated by dry and wet shear strengths and the pH value of each cured resin was checked to see its effect on the adhesion performance. The results indicated that the UMF-1 resin type by the addition of melamine initially with the urea and formaldehyde at the same F/(U+M) rate showed the lowest thermal stability, rigidity (${\Delta}E^{\prime}$), temperature of tan ${\delta}$ maximum ($T_{tan}\;_{\delta}$), and wet shear strength, and pH value of cured resin. In wet shear strength, however, the UMF-4 resin type appears to be slightly higher than UMF-1 resin type.

• 한국의류학회지
• /
• 제10권2호
• /
• pp.59-67
• /
• 1986

To control the amounts of formaldehyde released from the cotton fabric finished with N-methylol compounds, glycerol was used as a formaldehyde-scavenging agent. It was observed the effects of catalysts and curing conditions when aftertreated with glycerol on melamine resin finished fabric. The effects of Different processes of glycerol treatment, and different resins, urea resin and melamine resin, were compared. The conclusions obtained from the results are as follows: 1) It was shown hatt the aftertreatment with glycerol (treated without catalyst) was more effective than treated with catalysts in controlling free formaldehyde. 2) The optimum curing temperature and curing time for the glycerol aftertreatment without adversely affecting the other properties of fabric was about $160^{\circ}C$, 3 min. 3) According to the increase of glycerol concentration in both aftertreatment and simultaneous treatment the amounts of free formaldehyde was reduced. The rate of decrease was manifest within the limits of $6\%$ in the case of simultaneous treatment with glycerol ana resins, and $3\%$ in the case of glycerol aftertreatment on resin finished fabrics. 4) Dry wrinkle recovery angle was decreased the increase of glycerol concentration. Melamine resin had a little adverse effect than urea resin, particulary glycerol aftertreatment. 5) The breaking strength was increased with the increase of glycerol concentration.

• Journal of the Korean Wood Science and Technology
• /
• 제44권6호
• /
• pp.913-922
• /
• 2016

This study attempted to measure molecular weight (MW) of melamine-urea-formaldehyde (MUF) resins prepared by two different synthesis methods: the one-step MUF resins were synthesized in one batch procedure, while the two-step MUF resins were prepared by a physical mixing of urea-formaldehyde (UF) resin with melamine-formaldehyde (MF) resin that had been synthesized in a separate procedure. The properties of medium density fiberboard (MDF) panels bonded with two types of MUF resins were also investigated. MWs of these MUF resins were measured using gel permeation chromatography (GPC). In addition, this study measured the MWs of one-step MUF resin during its synthesis procedure. The performance of two types of MUF resins was evaluated by determining properties of MDF panels prepared in laboratory. As the synthesis procedure progressed, both number average MW ($M_n$) and weight average MW ($M_w$) of one-step MUF resin gradually increased, while the polydispersity index (PDI) decreased. And low Mw species of the resin predominantly decreased as the synthesis step progressed. The one-step MUF resin showed greater $M_n$ and $M_w$ than those of the two-step ones even though the PDI values of both resins were very similar each other. As expected, the one-step MUF resin resulted in better properties of MDF panels than those of two-step resins. In particular, the one-step MUF resin provided better internal bond (IB) strength and thickness swelling (TS) with MDF panels than those of two-step ones, indicating better water resistance of the one-step resin. These results suggest that the preparation method of MUF resins have a great impact on the MW and final panel properties.

• Journal of the Korean Wood Science and Technology
• /
• 제32권2호
• /
• pp.65-72
• /
• 2004

요소-멜라민수지 접착제를 실험실에서 수지 접착제 고형분량에 대해 5% 멜라민을 첨가하여 파티클보드 제조용으로 합성하였다. 합성한 요소-멜라민 수지를 이용하여 전건 목재파티클의 무게에 대해 접착제 첨가량 6, 8%와 열압시간 3, 4, 5분에서 실험실 파티클보드를 접착하는 열압시간동안 배출되는 가스를 증류수에 용해·포집하여 얻어진 용액으로부터 포름알데히드 배출량을 미국 National Institute of Occupational Safety and Health (NIOSH) 3500의 방법에 의해 분석·비교하였다. 포름알데히드 배출량을 측정하여 분석한 결과는 파티클보드를 열압하는 시간동안 배출되는 가스 중에서 포름알데히드량은 요소-멜라민수지 접착제의 첨가량과 열압시간에 대해 통계적으로 유의하게 차이가 있다는 것을 보여줬다. 파티클보드의 성능평가 결과는 3분의 열압시간에서 접착된 파티클보드의 박리강도는 KS F 3104 파티클보드 8.0형의 최소요구치를 만족시키는 것을 보여줬다.