• 폴리머
• /
• 제29권5호
• /
• pp.481-485
• /
• 2005

본 연구에서는 2관능성 에폭시 수지에 기상성장 탄소나노섬유(VGCNFs)를 0, 0.1, 0.5, 1.0 그리고 $2wt\%$ 함량 비로 첨가하여, 제조한 VGCNFs/에폭시 복합재료의 열적 및 기계적 특성을 고찰하고자 하였다. VGCNFs/에폭시 나노복합재료의 열적 특성은 TMA와 DMA로 알아보았으며, 기계적 특성은 만능 시험기와 낙하 충격 시험기 및 마찰$\cdot$마모 시험기를 통하여 관찰하였다. 실험 결과. VGCNFs의 함량이 증가할수록 열적 및 기계적 특성이 향상됨을 확인할 수 있었는데, 이는 현재의 복합재료 시스템에 있어서 VGCNFs와 에폭시 사이의 기계적 얽힘 현상의 향상을 가져오는 복합재료의 가교구조의 증가 때문이라 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.336-341
• /
• 1998

Steel fiber reinforced concrete(SFRC) is a composite material possessing many physical and mechanical properties which are distinct from unreinforced concrete. The use of steel fiber reinforcement to improve the flexural and tensile strengths, extensibility and toughness of ordinary cement concrete is well known at present, but reinforcement of polymer concrete with steel fibers has been hardly reported untill now. The objective of this study was to improve the properties of the polymer concrete by addition of steel fibers. In this paper steel fiber reinforced polymer concrete is prepared with various steel fiber contents and aspect ratio($\ell$ /d), and their mechanical properties were investigated experimentally.

• Fibers and Polymers
• /
• 제7권3호
• /
• pp.245-249
• /
• 2006

The effect of scouring, bleaching and dyeing on the low stress mechanical and surface properties of wool woven fabrics was studied. Fabric properties were measured by the KES-FB system. In general, mechanical properties of the treated fabrics are greatly affected by scouring, moderately by dyeing and least by bleaching.

• Composites Research
• /
• 제26권4호
• /
• pp.213-217
• /
• 2013

The focus in the present work is to study the agro-waste corn husk bio-filler as reinforcement for polypropylene. These materials have been created by extrusion and injection molding. The effect of filler content by 10, 20, 30 and 40 wt. % and mesh sizes of 50~100, 100 and 300 on the mechanical properties was studied. For the un-notched specimens, the results of flexural strength showed a declining trend with increase the filler loading and the results of impact strength showed an increasing trend with increase the mesh size. In contrast, enhanced flexural modulus was observed with increasing filler loading and size.

• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.53-65
• /
• 2010

The rigid body inertia properties of a structure including the mass, the center of gravity location, the mass moments and principal axes of inertia are required for structural dynamic analysis, modeling of mechanical systems, design of mechanisms and optimization. The analytical approaches such as solid or finite element modeling can not be used efficiently for estimating the rigid body inertia properties of complex structures. Several experimental approaches have been developed to determine the rigid body inertia properties of a structure via Frequency Response Functions (FRFs). In the present work two experimental methods are used to estimate the rigid body inertia properties of a frame. The first approach consists of using the amount of mass as input to estimate the other inertia properties of frame. In the second approach, the property of orthogonality of modes is used to derive the inertia properties of a frame. The accuracy of the estimated parameters is evaluated through the comparison of the experimental results with those of the theoretical Solid Work model of frame. Moreover, a thorough discussion about the effect of accuracy of measured FRFs on the estimation of inertia properties is presented.

• 한국의류학회지
• /
• 제22권2호
• /
• pp.257-266
• /
• 1998

This study was conducted to examine the changes of the mechanical properties of the position in jean slacks during the wear, previously used for the wearing test, which were subjected to repeated tensile-shearing deformation using a simulated fatigue tester has been investigated and compared, by calculating both mechanical properties and hand value(HV) of these fabrics with KES-F system and the by obtaining the THV through these calculated properties. The results are as follows. 1. The fatigue phenomenon of mechanical properties was the LT, 2H B, 2HBS, MMD, SMD, RC values increased, elasticity values of tensile, bending and shearing properties, such as B, G and compression properties LC, WC were reduced. It was shown, then, that those fabrics lost their elasticity and became flexible and soft with the increase of fatigue. 2. The hand value and THV; except anterior knee from all part of KOSHI, NUMERI, FUKURAMI was decreased. 3. The fatigue phenomenon of hand value was different on the position of clothing; on the position of hip, rate of B, G smaller than other parts and KOSHI was decreased, on the part of anterior thigh was FUKURAMI was increased, on the anterior knee RC, NUMERI, THV was increased, on the posterior knee was 2HB, 2HG, 2HGS showed increasedgreater than any other part and on the hem of back, MMD was increased, but NUMERI was decreased. 4. The changing process of mechanical properties in the simulation testing by the fatigue tester has similar tendency to that of the wearing tester. It is concluded that this testing method is useful to predict the fatigue phenomena of fabrics caused by wearing.

• 열처리공학회지
• /
• 제29권5호
• /
• pp.220-226
• /
• 2016

The mechanical properties of Ti-6Al-4V can be improved by microstructural control through the heat treatment in ${\alpha}+{\beta}$ region. The heat treatment was carried out with a variety of heat treatment temperatures and holding times to find the optimized heat treatment conditions and it was analyzed by linking the microstructural characteristics and mechanical properties. The part of ${\beta}$ phase with $10{\pm}2wt%$ vanadium was transformed into ${\alpha}^{{\prime}{\prime}}$ martensite phase after quenched, so the hardness and tensile properties were decreased below $900^{\circ}C$. The higher the heat treatment temperature is, the smaller is the vanadium-rich region, which leads to transformation into hcp ${\alpha}^{\prime}$ martensite above $900^{\circ}C$. The hardness and tensile properties were improved due to the hard ${\alpha}^{\prime}$ martensite. As the holding times were longer, the hardness and tensile properties decreased below $900^{\circ}C$ because of the softening effect by the grain growth. When varying the holding times above $900^{\circ}C$, the change of mechanical properties was slight because the softening effect of grain growth and the strengthening effect of ${\alpha}^{\prime}$ phase were counteractive. Therefore, the best conditions of heat treatment, which is in the range of $920{\sim}960^{\circ}C$, 40 min, WQ, can effectively improve the mechanical properties of Ti-6Al-4V.

• Journal of the Korean Wood Science and Technology
• /
• 제51권2호
• /
• pp.109-132
• /
• 2023

The objective of this study was to reveal the impact of thinning and pruning regimes on the physical and mechanical properties of clonal teak wood planted in Java. In this study, a 15-year-old clonal teak plantation was carried out and the obtained data were evaluated with analysis of variance (ANOVA). The results showed that different thinning intensities had a significant impact on the alteration of heartwood volume development (F = 25.63; p < 0.0001). Meanwhile, the impact of different thinning treatments in several physical properties depends on the pruning treatment levels [moisture content (F= 12.18, p < 0.0001); tangential shrinkage (F = 15.60, p < 0.0001); T/R ratio (F = 7.17, p < 0.0001); and volumetric shrinkage (F = 10.81, p < 0.0001)]. However, different thinning intensities had no significant impact on wood basic density alteration (F = 0.72, p = 0.486), while pruning intensities affect the differences between radial (F = 3.52, p = 0.030) and volumetric shrinkage (F = 3.13, p = 0.044). In mechanical properties, thinning intensity levels did not promote any significant differences [modulus of elasticity (F = 1.41, p = 0.248); modulus of rupture (F = 0.94, p = 0.392); compressive strength parallel to grain (F = 0.21, p = 0.813); and compressive strength perpendicular to the grain (F = 0.41, p = 0.669)]. Meanwhile, different pruning treatments and combination treatments were not significantly altered all mechanical properties. These results indicated that the thinning and pruning regimes can enhance the mechanical properties without having a serious alteration in the physical properties of clonal teak wood.

• Composites Research
• /
• 제37권3호
• /
• pp.197-203
• /
• 2024

고분자 복합재료의 기계적 특성 향상에 유리한 탄소섬유(Carbon fiber, CF)와 전도 특성 향상에 유리한 다중벽 탄소나노튜브(Multi-walled carbon nanotube, MWCNT)의 동시 혼입을 통해 기계적, 전기적 및 열적 특성을 동시에 향상시킬 수 있다. 본 연구에서는 우수한 양산 가공성과 준수한 기계적 특성을 나타내는 탄소장섬유 열가소성플라스틱(Carbon long fiber thermoplastic, CLFT)에 MWCNT를 혼입하여 전기적 및 열적 특성 제어하였다. 제조된 복합재료의 기계적 및 전기적 특성은 필러의 혼입 양에 가장 크게 영향을 받았다. 반면, 열적 특성은 MWCNT의 혼입으로 연결된 필러 네트워크가 형성됨으로써 더 우수한 결과를 나타내었다. MWCNT 혼입 CLFT의 필러 혼입량, 필러 조성 및 필러 네트워크 구조를 조절함으로써 목적에 적합한 기계적, 전기적 및 열적 특성 제어할 수 있었다.

• Steel and Composite Structures
• /
• 제29권3호
• /
• pp.405-422
• /
• 2018

In this research, experimental tensile test and manufacturing of carbon nanotube reinforced composite beam (CNTRC) is presented. Also, bending, buckling, and vibration analysis of CNTRC based on various beam theories such as Euler-Bernoulli, Timoshenko and Reddy beams are considered. At first, the experimental tensile tests are carried out for CNTRC and composite beams in order to obtain mechanical properties and then using Hamilton's principle the governing equations of motion are derived for Euler Bernoulli, Timoshenko and Reddy theories. The results have a good agreement with the obtained results by similar researches and it is shown that adding just two percent of carbon nanotubes increases dimensionless fundamental frequency and critical buckling load as well as decreases transverse deflection of composite beams. Also, the influences of different manufacturing processes such as hand layup and industrial methods using vacuum pump on composite properties are investigated. In these composite beams, glass fibers used in an epoxy matrix and for producing CNTRC, CNTs are applied as reinforcement particles. Applying two percent of CNTs leads to increase the mechanical properties and increases natural frequencies and critical buckling load and decreases deflection. The obtained natural frequencies and critical buckling load by theoretical method are higher than other methods, because there are some inevitable errors in industrial and hand layup method. Also, the minimum deflection occurs for theoretical methods, in bending analysis. In this study, Young's and shear modulli as well as density are obtained by experimental test and have not been used from the results of other researches. Then the theoretical analysis such as bending, buckling and vibration are considered by using the obtained mechanical properties of this research.