• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.885-886
• /
• 2006

Significant advances in mechanical testing for hard materials are discussed in this paper. There are three specific areas that are covered. In the measurement of fracture toughness factors such as the control of slow crack growth to produce strating cracks, and evaluating reproducibility and repeatability of tests have been recently examined. The miniaturization of tests reduces the amount of material that is used in testing, improves the throughput of tests, and also improves cost effectiveness. New techniques such as stepwise testing and micro scratch testing have contributed to significant additions to the knowledge of the wear mechanisms that operate in these materials.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.5
• /
• pp.53-60
• /
• 2010

The effects of blast furnace slag, hwang-toh, and reinforcing fiber on the physical and mechanical properties of porous concrete using blast furnace slag coarse aggregates have been evaluated in this study. The effect of the depending on replacement ratio of blast furnace slag to cement was investigated such that the replacement ratio was varied to 0 %, 25 % and 50 %. Also, the replacement ratios of hwang-toh were 0, 20 and 30 %. The polyvinyl alcohol fiber was used for the reinforcing fiber. A series of pH, unit mass, and void ratio tests have been performed to study the physical properties of the porous concrete using blast furnace slag coarse aggregates with the polyvinyl alcohol fiber and the replacement ratios of blast furnace slag, hwang-toh, while a series of compressive tests have been performed to evaluate the strength property depending on polyvinyl alcohol fiber and the replacement ratios of blast furnace slag, hwang-toh. The test results indicated that the physical and mechanical properties of porous concrete using blast furnace slag coarse aggregates is affected by the replacement ratio of blast furnace slag, and the fiber contents. According to the tests with polyvinyl alcohol fiber contents, the void ratio was decreased and the compressive strength was upgraded.

• Nuclear Engineering and Technology
• /
• v.52 no.3
• /
• pp.597-609
• /
• 2020

Accident Tolerant Fuels have been widely studied since the Fukushima-Daiichi accident in 2011 as one of the options on how to further enhance the safety of nuclear power plants. Deposition of protective coatings on nuclear fuel claddings has been considered as a near-term concept that will reduce the high-temperature oxidation rate and enhance accidental tolerance of the cladding while providing additional benefits during normal operation and transients. This study focuses on experimental testing of Zr-based alloys coated with Cr-based coatings using Physical Vapour Deposition. The results of long-term corrosion tests, as well as tests simulating postulated accidents, are presented. Zr-1%Nb alloy used as nuclear fuel cladding serves as a substrate and Cr, CrN, Cr_xN_y layers are deposited by unbalanced magnetron sputtering and reactive magnetron sputtering. The deposition procedures are optimized in order to improve coating properties. Coated as well as reference uncoated samples were experimentally tested. The presented results include standard long-term corrosion tests at 360℃ in WWER water chemistry, burst (creep) tests and mainly single and double-sided high-temperature steam oxidation tests between 1000 and 1400℃ related to postulated Loss-of-coolant accident and Design extension conditions. Coated and reference samples were characterized pre- and post-testing using mechanical testing (microhardness, ring compression test), Thermal Evolved Gas Analysis analysis (hydrogen, oxygen concentration), optical microscopy, scanning electron microscopy (EDS, WDS, EBSD) and X-ray diffraction.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.11 s.254
• /
• pp.1494-1501
• /
• 2006

Mechanical and physical properties of a copper alloy for a liquid rocket engine(LRE) combustion chamber liner application were tested at various temperatures. All test specimens were heat treated with the condition they might experience during actual fabrication process of the LRE combustion chamber. Physical properties measured include thermal conductivity, specific heat and thermal expansion data. Uniaxial tension tests were preformed to get mechanical properties at several temperatures ranging from room temperature to 600$^{\circ}C$. The result demonstrated that yield stress and ultimate tensile stress of the copper alloy decreases considerably and strain hardening increases as the result of the heat treatment. Since the LRE combustion chamber operates at higher temperature over 400$^{\circ}C$, the copper alloy can exhibit time-dependent behavior. Strain rate, creep and stress relaxation tests were performed to check the time-dependent behavior of the copper alloy. Strain rate tests revealed that strain rate effect is negligible up to 400$^{\circ}C$ while stress-strain curve is changed at 500$^{\circ}C$ as the strain rate is changed. Creep tests were conducted at 250$^{\circ}C$ and 500$^{\circ}C$ and the secondary creep rate was found to be very small at both temperatures implying that creep effect is negligible for the combustion chamber liner because its operating time is quite short.

• The Journal of Engineering Geology
• /
• v.27 no.4
• /
• pp.451-462
• /
• 2017

Physical weathering caused by external forces and chemical weathering caused by the decomposition or alteration of constituent materials are the two factors that dominate the mechanical properties of rocks. In this study, a field investigation was undertaken to identify the physical and chemical weathering characteristics of the biotite granite and granitic weathered soils in Gyeongju, South Korea. Samples were collected according to their grade of weathering and subjected to modal analysis, XRD analysis, XRF analysis, physical property tests, particle size distribution tests, and slake durability tests. Modal and XRD analysis identified these rocks as biotite granite; secondary alteration minerals were not observed. Physical property tests and particle size distribution analyses indicate an average porosity of 41.28% and a sand content of > 90 wt.%. These values are somewhat higher than those of granites in general. The results of the slake durability test and XRF analyses show that the physical and chemical weathering indices of the samples vary with the degree of weathering.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.20 no.4
• /
• pp.4805-4811
• /
• 1978

This paper deals with the correlations between the results of the physical property tests and the mechanical property tests for estimating the mechanical indexes by the physical property test results. The soil samples were taken at changweon area, Gyeon-gsangnam-do, where the structures would be placed on the alluvial clay foundation. The outcomes of the study are as follows: 1. Judging from casagrande's plasticity chart, it is considered that the almost all soil samples belong to inorganic silty clay with medium plasticity (clay 14∼62%, silt 36∼73%, sand 1∼29%). The specific gravities are between 2.61 and 2.72, the wet unit weights 1.53g/㎤ and 1.93g/㎤, the liquid limits 28% and 51%, the plastic limits 15% and 31%, the plastic indexes 7% and 27%, the natural moisture contents 33% and 64%. 2. The unconfined compression strengths are between 0.07kg/$\textrm{cm}^2$ and 0.77kg/$\textrm{cm}^2$, the cohesions 0.04kg/$\textrm{cm}^2$ and 0.37kg/$\textrm{cm}^2$, the internal friction angles 0$^{\circ}$ and 9$^{\circ}$. 3. The consolidation tests show that the initial void ratios are between 0.68 and 1.68, the precompression loads 0.27kg/$\textrm{cm}^2$ and 1.15kg/$\textrm{cm}^2$, the compression indexes 0.12 and 0.59. 4. The correlations between the results of the physical property tests and the mechanical property tests for the soil samples are presented as follows: rt=0.011 (203-wn), Cc=0.025 (LL-27.2), Cc=0.46 (e0-0.58), Cc=0.013 (wn-23.2), C=0.021+qu/2.08, qu=2.268rt-3.635

• Journal of the Korean Geotechnical Society
• /
• v.31 no.7
• /
• pp.41-52
• /
• 2015

Volcanic rocks in Jeju Island have vesicular structure caused by various environmental factors, and indicate the differences in geological and mechanical characteristics from region to region. In addition, the bedrock of Jeju Island shows stratified structure, that is, soft layers composed of pyroclastic rocks or cavities are irregularly developed between the basalt layers by several times of volcanic activity. In this study, various physical tests and unconfined compressive strength test were conducted for intact rocks sampled in northwestern onshore and offshore of Jeju Island. The results obtained in the tests were compared with the physical and mechanical characteristics of intact rocks sampled in southeastern offshore of Jeju Island. As a results, it was confirmed that the physical and mechanical characteristics of basalts sampled in northwestern Jeju Island were similar to those of basalts sampled in southeastern offshore of Jeju Island. In addition, it was possible to estimate approximate design parameters from the correlation of mechanical properties with physical properties of basalts in Jeju Island.

• Journal of the Korean Society of Industry Convergence
• /
• v.15 no.1
• /
• pp.21-27
• /
• 2012

Decomposed granite soils are in a wide range of conditions depending on the degrees of weathering. This paper is intended to examine laboratory tests such as consolidation tests and conventional triaxial compression tests conducted in order to find out the mechanical properties of Cheongju granite soil. Along with the foregoing, the results of basic physical tests conducted in order to grasp the physical properties of Cheongju granite soil were described and based on the results, methods to calculate the mechanical parameters of numerical approaches using Lade's double surface work-hardening constitutive model were examined. Finally, it is intended to explain the stress properties of Cheongju granite soil used as a geotechnical material based on its shear behavior and critical state concept using the results of isotropic consolidation tests and triaxial compression tests. As a conclusion, it can be seen that in the relationship between confining stress and maximum deviator stress, the slope is maintained at a constant value of 2.95. In the drained CTC test, maximum deviator stress generally existed in a range of axial strain of 6~8% and larger dilatancy phenomena appeared when confining stress was smaller. Finally, based on the results of the CTC tests on Cheongju granite soil, although axial strain, deviator stress and pore water pressure showed mechanical properties similar to those of overconsolidated soil, Cheongju granite soil showed behavior similar to that of normally consolidated soil in terms of volumetric strain.

• Tunnel and Underground Space
• /
• v.18 no.5
• /
• pp.317-327
• /
• 2008

About 70% of domestic land is mountainous and the construction of many geotechnical structures is inevitable for building transportation networks across region. Many geotechnical surveys, including rock physical and mechanical tests, are performed during construction. Thus study is a basic research for establishing database of physical and mechanical properties in domestic rocks, and analyzing the rock mechanical relationships between 2,000 rock properties obtained from laboratory tests in KOLAS. For the construction of useful database, systematic management, based on the standard information as well as reliable data accumulation, is required.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.345-350
• /
• 1999

In this study the results of investigation on the physical and mechanical properties of a rockfill dam body were provided. On the crest of the old Namgang dam to be excavated partially, various in-situ tests(boring with SPT, sampling of undisturbed sample, field density test, field permeability test) and geophysical investigation works were performed Rock materials, i.e., shale and sandstone, were collected, and their slake durability was evaluated using slaking durability testing method which is suggested by ISRM.