• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.43-50
• /
• 2007

Reheating furnace is an essential facility of a rod mill plant where a billet is heated to the required rolling temperature so that it can be milled to produce wire. Although it is very important to obtain information on billet temperatures, it is not feasible during furnace operation. Consequently, a billet temperature profile should be estimated. Moreover, this estimation should be done within an appropriate time interval for an on-line application. In this paper, a billet heat transfer model based on 2D FEM(Finite Element Method) with spatially distributed emission factors is proposed for an on-line billet temperature estimation and also a measurement is carried out for two extremely different furnace operation patterns. Finally, the difference between the model outputs and the measurements is minimized by using a new optimization algorithm named uDEAS(Univariate Dynamic Encoding Algorithm for Searches) with multi-step tuning strategy. The obtained emission factors are applied to a simulation for the data which are not used in the model tuning for validation.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.51-55
• /
• 2004

Surface plasmons (SPs) are charge density oscillations that propagate along an interface between a dielectric and metal. In this paper, the electric field of SPs and the intereference of two SPs are observed by using Near-field Scanning Optical Microscope (NSOM). The excitation condition of SPs is changed as the optical tip approaches the metal surface, because the excitation condition of SPs is very sensitive to surface structures. To measure the microscope field of SPs, the distance between metal surface and optical tip must contain a specific interval.

• Journal of the Korean Institute of Navigation
• /
• v.3 no.2
• /
• pp.21-30
• /
• 1979

Echo sounder and Doppler sonar are to theultra-sonic transducers for measuring the depth and the ship's speed respectively. To measure the depth and speed with a single transducer, it is required to control the ultra-sonic beam to optional direction. In the past, the direction of the transducer itself is varied, but such a method provoked much problems in the mechanical design of the equipment. This paper deals with the method to control beam direciton by the phase control of the plural arrangement of transducers, and the results are studied by a computer simulation. The remarkable results of the study is condensed as follows; 1. The greater the interval of arrangement between transducers, the sharper the radiation pattern is, but in this case, the level of undesired sidelobe is also increased. 2. The control of radiation pattern up to 60 degree can be achieved by an adequate arrangement of more than 10 transducers. 3. It is shown that a simultaneous measurement of both depth and speed can be achieved by alternating directivity of the pulse by the method proposed in this paper.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.112-117
• /
• 2016

This paper presents a half-rate current-integrating DFE receiver with sub-unit interval (sub-UI) inter-symbol interference (ISI) cancellation. By having a single additional DFE tap in each data path, the proposed DFE receiver can minimize BER degradation due to input pattern dependency and feedback tap latency problems in conventional current-integrating DFE receivers. The proposed DFE receiver was designed and fabricated in a 45 nm CMOS process, whose measurement results indicated that the BER bathtub width is increased from 0.235 UI to 0.315 UI (34% improvement) at $10^{-12}$ BER level.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.413-422
• /
• 2004

The flow characteristic in the wake around a circular cylinder with tripping wires, which was set in constant distance, was experimentally investigated in the uniform flow, Re=2.92$\times10^4$. The measurement of velocity vector and pressure distribution are carried out various angles of tripping wires in the range of $50^(\circ)$ to $80^(\circ)$ with $10^(\circ)$ interval. The results show that velocity profiles and pressure distributions are different with angles of tripping wires. The drag of the circular cylinder was decreased about 60% maximum when tripping wires' angle was $50^(\circ)$. The lowest reduction of the velocity and wake width was occurred by coanda effect when the angle was $60^(\circ)$, and the vortex shedding periodicity become rare at the same time.

• Journal of the Korean Chemical Society
• /
• v.6 no.2
• /
• pp.130-132
• /
• 1962

A new method of evaluating the mixing time in the continuous flow stirred tank is herein proposed. Experimental results to test the concept are also presented.The mixing time is defined as the time interval between the injection of a slug of an electrolyte solution into the tank and the moment at which an essentially straight line begins on a plot of the conductivity of effluent versus time.The proposed method of measuring the mixing time is valid even for the low mixing time (5 seconds) and the results obtained agree well with previous work, where the mixing time measurements were carried out by the injection of a dye into the feed stream.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.541-547
• /
• 1992

The phased array antenna has the ability to perform adaptive sampling by directing the radar beam without inertia in any direction. The adaptive sampling capability of the phased array antenna allows each sampling time interval to be varied for each target, depending on the acceleration of each target at any time. In this paper we design a three-dimensional adaptive tracking algorithm for the phased array radar system with a given set of measurement parameters. The tracking algorithm avoids taking unnecessarily frequent samples, while keeping the angular prediction error within a fraction of antenna beamwidth so that the probability of detection will not be degraded during a track update illuminations. In our algorithm, the target model and the sampling rate are selected depending on the target range and the target maneuver status which is determined by a maneuver detector. A detailed simulation is conducted to test the validity of our tracking algorithm for encounter geometries under various conditions of maneuver.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.4
• /
• pp.283-288
• /
• 2016

Optimizing the number of ad clicks is a large-scale learning problem that is central to the multi-billion-dollar mobile advertising industry. There are currently several optimization methods being used, including ad mediation and ad positioning. Recently, researchers have recommended using ad refresh interval as a new method for optimizing mobile advertising. This paper applies that new method to optimize content duration for mobile ads. The result achieved from this optimization study could further increase revenue for mobile advertisers and publishers. This research has high applicability for the growing mobile advertising industry. It also lays out a solid background for future research in this promising area.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.1
• /
• pp.113-120
• /
• 2002

Experimental procedure to measure fracture toughness (J$_{c}$) under mixed mode loading using CTS(Compact Tension-Shear) specimens is described. It\`s loading angle ranges from 0$^{\circ}$ to 45$^{\circ}$ with interval of 157. The general outline of experimental procedure is similar to that of ASTM E8l3-89 fur mode I fracture. Equations fur determining J-integral is quoted from the authors' previous works. The relation between unloading compliance and physical crack size was calibrated. As an example, fracture toughness of aluminum alloy 2024p-7361 was measured and some reasonable results of J$_{c}$ with various loading angles were obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.27-30
• /
• 2002

In this paper, we were investigated leakage current properties of outdoor insulator on climatic environmental factor. Contamination is one of the most important factor to determine the performance of insulator. Thus, it is very important to exam the contamination degree on the outdoor insulator. There are many limits, such as reliability of data, interval of measurement and similarity of environmental conditions, in conventional method. So, we measured phase and leakage current of outdoor insulator using the temperature & humidity chamber. In this investigation, phase difference was measured to compare the variance of phase difference with the contamination degree and relative humidity.