• Journal of the Korea Convergence Society
• /
• v.9 no.3
• /
• pp.165-171
• /
• 2018

In this study, to analyze the detection of limit for sensitivity of the influenza rapid antigen test kit, the positive detection of limits were analyzed by serial dilution of influenza virus A and B type for five influenza rapid antigen test kits in Korea. As a result of analysis, visual measurement of type A were up to 1:8192 for the Wellsbio product and up to 1:4096 for the II product, up to 1:512 for the I and III products, and only 1:128 for the IV product, and type B were positive for up to 1:8192 for the Wellsbio product, up to 1: 4096 for the II product and up to 1:1024 for the I, III and IV products. For instrument readings with the same specimen, both A and B types were found to be positive for up to 1:8192 for the Wellsbio product, up to 1: 4096 for the II product, and up to 1:2048 for the I product. The sensitivity of the rapid antigen test for influenza differs greatly depending on the sampling area of the patient, infection period, specimen volume, etc. Therefore, it is necessary to observe exactly the collection timing and method of the specimen. And it is necessary further study to improve the sensitivity for influenza rapid antigen test.

• Applied Biological Chemistry
• /
• v.37 no.5
• /
• pp.343-348
• /
• 1994

Ti plasmid of A. tumefaciens was labeled with $^3H-thymidine$, purified and encapsulated into phosphatidylserine (PS) and PS-cholesterol (Chol; 1 : 1 molar ratio) liposomes by lyophilization-rehydration method. PS was supplemented with 1 mole percent octadecyl rhodamine B for fluorometric measurement of PS. Liposomes entrapping $^3H-Ti plasmid$ were fused with Nicotiana sanderae protoplasts by treating with 5 mM $CaCl_2$ and 10% PEG. The fusion was evidenced by fluorescence microscopic technique. The amounts of Ti plasmid and PS associated with protoplasts were assayed by the radioactivity of $^3H-Ti plasmid$ and by the fluorescence of rhodamine B. About 7.9% of the PS liposome and 7.2% of PS-Chol liposome were fused with protoplasts. During the fusion process, about 30% of the liposomal contents of PS-Chol liposome was leaked, in contrast to about 60% leakage of its contents in PS liposome. Accounting the number of liposomes fused with protoplasts together with the encapsulation efficiency and the leakage of liposomal contents, it was calculated that ca. 1,700 Ti plasmid was transfered into one protoplast by the present method. This result may indicates that the present method transfers enough Ti plasmid into plant protoplast to elicit genetic transformation of plants.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4125-4130
• /
• 2015

This paper presents the communication performance for the radiation pattern reconfigurable antenna in the wearable device measuring bio signal (temperature, blood pressure, pulse etc.) of human body. The operational frequency is 2.4 - 2.5 GHz, which covers Bluetooth communication bandwidth. The maximum gain of the antennas is 1.96 dBi. The proposed antenna is efficiently transmitting and receiving signal by generating two opposite beam directions using two RF switches (PIN diode). Also, we investigated how radiation pattern changes according to three angles ($30^{\circ}$, $90^{\circ}$, $150^{\circ}$) of Top Loading. In this paper, we measured and compared the SNR (Signal-to-Noise Ratio) and BER (Bit Error Rate) performances of the proposed antennas in the condition between an ideal environment of anechoic chamber and smart house existing practical electromagnetic interferences (Universal Software Radio Peripheral, USRP). Throughout the comparing the results of the measurement of two cases, we found that the SNR is degraded over 5dB in average and BER is increased over ten times in maximum, therefore, it is confirmed that the error rate of receiving signal is increased. The measured results of SNR and BER value in this paper able to expect the performance degrading by the interference from the electromagnetic devices.

• Korean Journal of Construction Engineering and Management
• /
• v.25 no.2
• /
• pp.11-22
• /
• 2024

Power plant engineering industry obtains EPC plan project and delivers results about electricity, measurement, machinery, and piping and so on. Its works are taken by projects. Although power plant engineering composes 2~5% of whole EPC project cost, it's one of the fundamentals because it affects process after planning step a lot. However, domestic power plant engineering companies' project performance ability is insufficient and there's a need for systematic performance. Thus, this study defined related factors of successful performance and analyzed the priority among them through analytical hierarchy process. All respondents recognized experience, knowledge, and communication as important factors. Administrators considered knowledge, experience, and communication. But hands-on workers considered experience, knowledge, human resources. Those who have experience in oversea project considered process, experience, human resources. However those who don't have experience in oversea project considered knowledge, experience, and communication. Recognition of important factors varies by the position and work experience of members.

• Molecules and Cells
• /
• v.20 no.1
• /
• pp.142-150
• /
• 2005

Members of the multifunctional Cyp family have been isolated from a wide range of organisms. However, few functional studies have been performed on the role of these proteins as chaperones in red alga. For studying the function of cDNA GjCyp-1 isolated from the red alga (Griffithsia japonica), we expressed and purified a recombinant GjCyp-1 containing a hexahistidine tag at the amino-terminus in Escherichia coli. An expressed fusion protein, $H_6GjCyp-1$ maintained the stability of E. coli proteins up to $50^{\circ}C$. For a functional bioassay for recombinant $H_6GjCyp-1$, the viability of E. coli cells overexpressing $H_6GjCyp-1$ was compared with that of cells not expressing $H_6GjCyp-1$ at $50^{\circ}C$. After high temperature treatment for 1 h, E. coli overexpressing $H_6GjCyp-1$ survived about three times longer than E. coli lacking $H_6GjCyp-1$. Measurement of the light scattering of luciferase (luc) showed that GjCyp-1 prevents the aggregation of luc during mild heat stress and that the thermoprotective activity of GjCyp-1 is blocked by cyclosporin A (CsA), an inhibitor of Cyps. Furthermore, the Cyp-CsA complex inhibited the growth of E. coli under normal conditions. The results of the GjCyp-1 bioassays as well as in vitro studies strongly suggest that Cyp confers thermotolerance to E. coli.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.511-518
• /
• 2010

The split Hopkinson pressure bar (SHPB) has been widely used to determine the mechanical properties of materials at high loading rates. However, to ensure test reliability, the source of measurement error must be identified and eliminated. During the experiment, specimens were placed between the incident and the transmit bar. Contact friction between the test bars and specimen may cause errors. In this study, numerical experiments were carried out to investigate the effect of friction on the test results. In the SHPB test, the stress measured by the transmitted bar is assumed to be the flow stress of the test specimen. However, performing numerical experiments, it was shown that the stress measured by the transmit bar is axial stress components. When the contact surface is frictionless, the flow stress and axial stress of the specimen are approximately equal. On the other hand, when the contact surface is not frictionless, the flow stress and axial stress are no longer equal. The effect of friction on the difference between the flow stress and axial stress was investigated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.9
• /
• pp.1837-1845
• /
• 2015

The longitudinal velocity is necessary for accurate vehicular positioning in urban environment. The pitch angle, which is a road slope, should be calculated to acquire the longitudinal velocity. However, it is impossible to consider very accurate pitch, when using a sensor and an algorithm. That's why process noise and positioning stimation error of IMU should be adjusted to the driving environment and fuse GPS, OBD data with ACF which consist of AKF, CF in this paper. Then, final pitch angle which is appropriate for driving environment is estimated by IMMKF in order to optimize the system model according to road slope models.

• Journal of Environmental Science International
• /
• v.25 no.2
• /
• pp.239-246
• /
• 2016

This study aims to analyze region-specific trends in changing greenhouse gas emissions in incineration plants of local government where waste heat generated during incineration are reused for the recent five years (2009 to 2013). The greenhouse gas generated from the incineration plants is largely $CO_2$ with a small amount of $CH_4$ and $N_2O$. Most of the incineration plants operated by local government produce steam with waste heat generated from incineration to produce electricity or reuse it for hot water/heating and resident convenience. And steam in some industrial complexes is supplied to companies who require it for obtaining resources for local government or incineration plants. All incineration plants, research targets of this study, are using LNG or diesel fuel as auxiliary fuel for incinerating wastes and some of the facilities are using LFG(Landfill Gas). The calculation of greenhouse gas generated during waste incineration was according to the Local Government's Greenhouse Emissions Calculation Guideline. As a result of calculation, the total amount of greenhouse gas released from all incineration plants for five years was about $3,174,000tCO_2eq$. To look at it by year, the biggest amount was about $877,000tCO_2eq$ in 2013. To look at it by region, Gyeonggido showed the biggest amount (about $163,000tCO_2eq$ annually) and the greenhouse gas emissions per capita was the highest in Ulsan Metropolitan City(about $154kCO_2eq$ annually). As a result of greenhouse gas emissions calculation, some incineration plants showed more emissions by heat recovery than by incineration, which rather reduced the total amount of greenhouse gas emissions. For more accurate calculation of greenhouse gas emissions in the future, input data management system needs to be improved.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.3
• /
• pp.87-99
• /
• 1991

The effect of oven firing on the color stability and surface texture of extrinsic stains used characterization and color modification of metal cermic restoration were studied by comparing different temperatures and techniques. They were autoglaze technique, applied glaze technique, two step low-fusing glaze technique and one step low-fusing glaze technique. Autoglaze technique and applied glaze technique were air-fired to manufacturer's recommended temperature. Two step low-fusing glaze technique is separated staining and overglazing. Thin slurry of stain powder were air-fired to $1500^{\circ}F$, Overglaze powder powder was then mixed with seam medium and air-fired to $170^{\circ}F$. One step low-fusing glaze technique is combined staining and overglazing. Thin slurry of stain and glaze powder were air-fired to $170^{\circ}F$. The obtained results were as fellows. 1. Slightly significant color differences by colorimeter were found between different stain application and fusion techniques(P<0.05). 2. Two step low-fusing glaze method showed the most rough surface, especially ceramco orage stain(P<0.05). 3. Surface roughness increased gradually in order of autoglaze, applied glaze, one step low-fusing glaze but they were not significantly different(P<0.05). 4. When two step low-fusing glaze was applied, both color measurement and surface texture were sinificantly different from other groups(P<0.05).

• Journal of Microbiology and Biotechnology
• /
• v.11 no.1
• /
• pp.131-137
• /
• 2001

Previous work has identified that only the catabolite responsive element A (creA; previously called cre-2) out of two potential cre sequences (cre-1: nucleotide +160 to +173 and cre-2: +173 to +186), recognized within the coding region of the xylanaseA gene (xynA) of Bacillus stearothermophilus No.236, was actually, was actually involved in the carbon catabolite repression(CCR) of xynA expression in B. subtilis. However, the level of CCR of xynA expression in the original B.stearothermophilus No.236 strain (70-fold repression). Therefore, to search for an additional cre element in the promoter region, the upstream region of the xynA gene was subcloned by chromosome walking, and as a result, another potential cre element (nucleotide -124∼-137; designated creB) was recognized in this region. The cre-like sequence revealed a high homology to the cre consensus sequence. The xylanase activity of B. subtilis MW15 bearing pWPBR14 (containing creA and creB) cultured in a medium containing xylose as the sole carbon source was about 7.7 times higher than that observed for the same culture containing glucose. B. subtilis MW15 bearing pWPBR23 (containing only creA) produced an activity about 2.4 times higher. This pattern of CCR was confirmed using derivatives of xynA::aprA fusion plasmids. Furthermore, a measurement of the amounts of the xynA transcript showed a similar pattern as that for the production of xylanase. In addition, the synthesis of xylanase in B. subtilis QB7115 [a catabolite control protein A (ccpA) mutant strain] carrying pWPBR14 was almost completely relieved from glucose repression. Together, these results lead to a conclusion that the CCR of the expression of the xynA gene is mediated by CcpA binding at creA and creB sites in B. subtilis.