• Journal of Electrical Engineering and Technology
• /
• v.2 no.1
• /
• pp.136-141
• /
• 2007

The Purpose Of This Paper Is To Use A Tactile Sensor To Compensate The Error Rate. Most Automated Sphygmomanometers Use The Oscillometric Method And Characteristic Ratio To Estimate Systolic And Diastolic Blood Pressure. However, Based On The Fact That Maximum Amplitude Of The Oscillometric Waveform And Characteristic Ratio Are Affected By Compliance Of The Aorta And Large Arteries, A Method To Measure The Artery Stiffness By Using A Tactile Sensor Was Chosen In Order To Integrate It With The Sphygmomanometer In The Future Instead Of Using Photoplethysmography. Since Tactile Sensors Have Very Weak Movements, Efforts Were Made To Maintain The Subject's Arm In A Fixed Position, And A 40hz Low Pass Filter Was Used To Eliminate Noise From The Power Source As Well As High Frequency Noise. An Analyzing Program Was Made To Get Time Delay Between The First And Second Peak Of The Averaged Digital Volume Pulse(${\Delta}t_{dvp}$), And The Subject's Height Was Divided By ${\Delta}t_{dvp}$ To Calculate The Stiffness Index Of The Arteries($Si_{dvp}$). Regression Equations Of Systolic And Diastolic Pressure Using $Si_{dvp}$ And Mean Arterial Pressure(Map) Were Computed From The Test Group (60 Subjects) Among A Total Of 121 Subjects(Age: $44.9{\pm}16.5$, Male: Female=40:81) And Were Tested In 61 Subjects To Compensate The Error Rate. Error Rates Considering All Subjects Were Systolic $4.62{\pm}9.39mmhg$, And Diastolic $14.40{\pm}9.62mmhg$, And Those In The Test Set Were $3.48{\pm}9.32mmhg,\;And\;14.34{\pm}9.67mmhg$ Each. Consequently, Error Rates Were Compensated Especially In Diastolic Pressure Using $Si_{dvp}$, Various Slopes From Digital Volume Pulse And Map To Systolic-$1.91{\pm}7.57mmhg$ And Diastolic $0.05{\pm}7.49mmhg$.

• Journal of Animal Science and Technology
• /
• v.63 no.3
• /
• pp.651-661
• /
• 2021

This study aimed to investigate whether breed, sex, and age affected temperament differently (more or less neophobic) in mature horses during a novel object test. The study included Jeju crossbred (n = 12, age = 9.42 ± 4.57 y), Thoroughbred (n = 15, age = 10.73 ± 3.09 y), and Warmblood horses (n = 12, age = 13.08 ± 3.55 y) with the females (n = 22, age = 11.36 ± 4.24 y) and geldings (n = 17, age = 10.65 ± 3.66 y). Jeju crossbreds (Jeju horse × Thoroughbred) are valuable considering their popular usage in Korea, but limited studies have explored temperament of Jeju crossbred horses. A trained experimenter touched the left side of the neck with a white plastic bag (novel object). The test ended when the horse stopped escape response and heart rate (HR) dropped to baseline. Behavioral score and escape duration were measured as behavioral variables. Multiple variables related to HR and heart rate variability (HRV) were measured to reflect emotional state. These included basal HR (BHR), maximum HR (MHR), delay to reach maximum heart rate (Time to MHR), standard deviation of beat-to-beat intervals (SDNN), root mean square of successive differences (RMSSD), and ratio of low to high frequency components of a continuous series of heartbeats (LF/HF). Statistics revealed that Thoroughbreds had significantly higher behavioral scores, and lower RMSSD than Jeju crossbreds (p < 0.05), suggesting greater excitement and fear to the novel object in Thoroughbreds. None of the behavioral or cardiac parameters exhibited sex differences (p < 0.05). Age was negatively correlated with SDNN and RMSSD (p < 0.05), indicating that older horses felt more anxiety to the novelty than younger horses. Thoroughbreds and females had distinct correlations between behavioral and HRV variables in comparison with other groups (p < 0.05), implying that escape duration might be a good indicator of stress, especially in these two groups. These results are expected to improve equine welfare, safety and utility, by providing insights into the temperament of particular horse groups, to better match reactivity levels with specific functions.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.3
• /
• pp.55-67
• /
• 2019

Deep soft ground in mouth of Nackdong river requires to be analysed with prediction method concerning characteristics of secondary consolidation from the beginning because it causes excessive settlement due to time-dependant secondary consolidation characteristics. This study investigated characteristics of extended settlement by conducting one-dimensional theory, elasto-plastic model and visco-elasto-plastic model as well as analyzing long-term measuring data observed over 2,000 days. According to one-dimensional theory and elasto-plastic model, there is not definite correlation between height of embankment and depth of soft ground while visco-elasto-plastic model showed similar result of settlement to that of long-term measuring data. Consequently it is suggested that applying visco-elasto-plastic model to developing deep underground place as studied area on predicting extended settlement before construction prevents economic loss and delay during process by preparing secondary consolidation characteristics.

• The Korean Journal of Nuclear Medicine
• /
• v.5 no.1
• /
• pp.49-64
• /
• 1971

The radioactive $^{131}I$-rose bengal serial scintiphotography was performed in 62 patients with the hepatobiliary diseases and in 20 normal subjects. This approach permitted visualization of the hepatic uptake of $^{131}I$-rose bengal from the circulation and its excretion into the biliary trees and the intestines. In some of these patients, gallbladder function was examined, using eggs as a gallbladder constrictor. The time of maximum hepatic uptake was well correlated to the conventional biochemical liver function tests. In addition to $^{131}I$-rose bengal scintiphotography, $^{198}Au$-colloid scintiphotography was also performed to make comparison of these two tests. The results obtained were as follows: 1. In normal subjects, the maximum hepatic uptake of $^{131}I$-rose bengal occurred at $23{\pm}2.9$ minutes, the initial hepatic excretion at $34{\pm}5.1$ minutes, the visualization of the gallbladder at $29{\pm}5.7$ minutes and the intestinal visualization at $54{\pm}25.8$ minutes. The radioactivity in the gallbladder decreased to $10.7{\pm}5.0%$ one hour after the ingestion of eggs. 2. In the patients with cirrhosis of the liver, there was a delayed and decreased hepatic uptake. The maximun hepatic upake occurred at $43{\pm}12.9$ minutes. The differences in the results of uptake between the cirrhotic and the normal group were statistically significant. The initial hepatic excretion occurred at $60{\pm}18.5$ minutes and had tendency of delaying compared with the normal controls. The gallbladder was visualized in 13 of 16 cases (81%) and its visualization occurred at $49{\pm}14.6$ minutes with a tendency to be delayed compared with the normal controls. The intestinal visualization occurred at $63{\pm}15.8$ minutes and its delaying tendency was somewhat more prominent. 3. In patients with hepatitis, the maximum hepatic uptake occurred at $59{\pm}21.4$ minutes and was significantly delayed. The initial hepatic excretion occurred at $82{\pm}34.3$ minutes and the results revealed a delaying tendency. The gallbladder was visualized in 15 of 20 cases (75%) at $57{\pm}18.7$ minutes, which was significantly delayed. The Intestinal visualization was noted in all cases with marked delay. 4. In patients with obstructive jaundice, the maximum hepatic uptake was noted at $83{\pm}14.7$ minutes, showing the most significant delay. The hepatic excretion into biliary trees and intestines was not entirely noted in all cases except the only one case with gallbladder visualization. 5. In patients with cholelithiasis, the maximum hepatic upake and the initial hepatic excretion were slightly delayed with mean times of $39{\pm}11.2\;and\;48{\pm}17.1$ minutes respectively. The visualization of the gallbladder was demonstrated in 10 of 17 cases (59%) and occurred at $52{\pm}25.6$ minutes with a slight delay. The intestinal visualization occurred at $67{\pm}47.7$ minutes and was slightly delayed. $^{131}I$-rose bengal in the gallbladder remained high, $49.3{\pm}21.3%$, which suggested quantitatively decreased power of gallbladder constriction. 6. The time of the maximum hepetic uptake was correlated well to BSP retention and serum alkaline phosphatase ativity. However, the maximum hepatic uptake had no definite correlation with serum albumin, serum globulin, TTT, serum cholesterol, SGPT or SGOT. 7. In the diagnosis of the hepatobiliary diseases with jaundice, $^{131}I$-rose bengel serial scintiphotography has proved to be more useful than $^{198}Au$-colloid scintiphotography. With these results, it could be justified that $^{131}I$-rose bengal scintiphotography is an excellent diagnostic aid for dynamic hepatobiliary function studies in the clinical practice.

• Restorative Dentistry and Endodontics
• /
• v.27 no.2
• /
• pp.158-174
• /
• 2002

The aim of this study was to investigate the effect of light irradiation modes on polymerization shrinkage, degree of cure and microleakage of a composite resin. VIP$^{TM}$ (Bisco Dental Products, Schaumburg, IL, USA) and Optilux 501$^{TM}$ (Demetron/Kerr, Danbury, CT, USA) were used for curing Filtek$^{TM}$ Z-250 (3M Dental Products, St. Paul., MN, USA) composite resin using following irradiation modes: VIP$^{TM}$ (Bisco) 200mW/$\textrm{cm}^2$ (V2), 400mW/$\textrm{cm}^2$ (V4), 600mW/$\textrm{cm}^2$ (V6), Pulse-delay (200 mW/$\textrm{cm}^2$ 3 seconds, 5 minutes wait, 600mW/$\textrm{cm}^2$ 30seconds, VPD) and Optilux 501$^{TM}$ (Demetron/Kerr) C-mode (OC), R-mode (OR). Linear polymerization shrinkage of the composite specimens were measured using Linometer (R&B, Daejeon, Korea) for 90 seconds for V2, V4, V6, OC, OR groups and for up to 363 seconds for VPD group (n=10, each). Degree of conversion was measured using FTIR spectrometer (IFS 120 HR, Bruker Karlsruhe, Germany) at the bottom surface of 2 mm thick composite specimens V2, Y4, V6, OC groups were measured separately at five irradiation times (5, 10, 20, 40, 60 seconds) and OR, VPD groups were measured in the above mentioned irradiation modes (n=5 each). Microhardness was measured using Digital microhardness tester (FM7, Future-Tech Co., Tokyo, Japan) at the top and bottom surfaces of 2mm thick composite specimens after exposure to the same irradiation modes as the test of degree of conversion(n=3, each). For the microleakage test, class V cavities were prepared on the distal surface of the ninety extracted human third molars. The cavities were restored with one of the following irradiation modes : V2/60 seconds, V4/40 seconds, V6/30 seconds, VPD , OC and OR. Microleakage was assessed by dye penetration along enamel and dentin margins of cavities. Mean polymerization shrinkage, mean degree of conversion and mean microhardness values for all groups at each time were analyzed using one-way ANOVA and Duncan's multiple range test, and using chi-square test far microleakage values. The results were as follows : . Polymerization shrinkage was increased with higher light intensity in groups using VIP$^{TM}$ (Bisco) : the highest with 600mW/$\textrm{cm}^2$, followed by Pulse-delay, 400mW/$\textrm{cm}^2$ and 200mW/$\textrm{cm}^2$ groups, The degree of polymerization shrinkage was higher with Continuous mode than with Ramp mode in groups using Optilux 501$^{TM}$ (Demetron/Kerr). . Degree of conversion and microhardness values were higher with higher light intensity. The final degree of conversion was in the range of 44.7 to 54.98% and the final microhardness value in the range of 34.10 to 56.30. . Microleakage was greater in dentin margin than in enamel margin. Higher light intensity showed more microleakage in dentin margin in groups using VIP$^{TM}$ (Bisco). The microleakage was the lowest with Continuous mode in enamel margin and with Ramp mode in dentin margin when Optilux 501$^{TM}$ (Demetron/Kerr) was used.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.11B
• /
• pp.946-955
• /
• 2004

It is shown that the do Bruijn graph (dBG) can be used as an architecture for interconnection network and a suitable structure for parallel computation. Recent works have classified dBG based routing algorithms into shortest path routing and fault tolerant routing but investigation into fault free shortest path (FFSP) on dBG has been non-existent. In addition, as the size of the network increase, more faults are to be expected and therefore shortest path dBG algorithms in fault free mode may not be suitable routing algorithms for real interconnection networks, which contain several failures. Furthermore, long fault free path may lead to high traffic, high delay time and low throughput. In this paper we investigate routing algorithms in the condition of existing failure, based on the Bidirectional do Bruijn graph (BdBG). Two FFSP routing algorithms are proposed. Then, the performances of the two algorithms are analyzed in terms of mean path lengths and discrete set mean sizes. Our study shows that the proposed algorithms can be one of the candidates for routing in real interconnection networks based on dBG.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.8
• /
• pp.2484-2496
• /
• 2000

High speed switches have been developing to interconnect a large number of nodes. It is important to analyze the switch performance under various conditions to satisfy the requirements. Queueing analysis, in general, has the intrinsic problem of large state space dimension and complex computation. In fact, The petri net is a graphical and mathematical model. It is suitable for various applications, in particular, manufacturing systems. It can deal with parallelism, concurrence, deadlock avoidance, and asynchronism. Currently it has been applied to the performance of computer networks and protocol verifications. This paper presents a framework for modeling and analyzing ATM switch using stochastic activity networks (SANs). In this paper, we provide the ATM switch model using SANs to extend easily and an approximate analysis method to apply A TM switch models, which significantly reduce the complexity of the model solution. Cell arrival process in output-buffered Queueing A TM switch with finite buffer is modeled as Markov Modulated Poisson Process (MMPP), which is able to accurately represent real traffic and capture the characteristics of bursty traffic. We analyze the performance of the switch in terms of cell-loss ratio (CLR), mean Queue length and mean delay time. We show that the SAN model is very useful in A TM switch model in that the gates have the capability of implementing of scheduling algorithm.

• Journal of Broadcast Engineering
• /
• v.16 no.2
• /
• pp.207-215
• /
• 2011

A signal passed through multi-path channel suffers ISI(Inter-Symbol Interference) and severe distortions caused by channel delay spread and noise components at the SC-FDE(Single Carrier with Frequency Domain Equalizer) transmission. Conventional UW(Unique-Word) based SC-FDE iterative channel estimation improves channel estimation performance by smoothing estimated CIR(Channel Impulse Response) of the noise components outside the channel length at time domain and restoring the broken cyclic property through UW reconstruction. In this paper, we propose channel estimation scheme through noise suppression within channel length. To suppress the noise, we estimate noise standard deviation as estimated CIR of the noise components outside the channel length and make criteria of the noise standard deviation gain that doesn't affect the original signal samples. When estimated CIR samples within channel length are less than the criteria value using the noise standard deviation and gain, the noise components are removed. Simulation results show that the proposed channel estimation scheme brings good channel MSE(Mean Square Error) and good BER(Bit Error Rate) performance.

• Journal of Veterinary Clinics
• /
• v.29 no.1
• /
• pp.38-42
• /
• 2012

To determine the prevalence of the primary glaucoma (PG) and occurrence of primary glaucoma in initially non-affected normal eye. Medical records of 7751 dogs presented to the Veterinary Medical Teaching Hospital (VMTH) of Seoul National University (SNU) between January 2006 and December 2009 were examined. Among 7751 dogs, forty three dogs (0.55%) developed PG. The following breeds were included in the study: 18 American Cocker Spaniels, 17 Shih Tzus, 3 Mixed Breeds, 2 Malteses, 2 Pekingeses, and 1 Chow Chow. The mean onset age of PG in the first eyes was $7.1{\pm}2.3$ years in the all breeds. Compared with Mixed Breed (0.54%), American Cocker Spaniel (3.16%, p = 0.004) and Chow Chow (20%, p = 0.001) had a higher risk of developing glaucoma. Twenty six of 43 dogs (60.1%) were females with male-to-female ratio of 1:1.53. Twenty nine of 33 eyes (87.9%) developed glaucoma in the fellow eye within mean ${\pm}SD$ time of $17.5{\pm}2.7$ months. From this study, American Cocker Spaniel and Shih Tzu were the most frequent PG breed in Korea. Also, unilateral PG dogs developed glaucoma in the non-affected normal eye within approximately 17 months. The results indicate that prophylactic medical therapy with antiglaucoma agents should be considered to delay or prevent developing glaucoma in non-affected normal eye.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.574-581
• /
• 2019

The present study analyzed the productivity and cost of winching operations for evaluating the efficiency of a tractor-attached winch in a Pinus densiflora thinning site located in the Yangyang County of Gangwon-do. The mean yarding distance and mean timber volume were 29 m and 0.15 ㎥, respectively. In the 95 cycles of yarding operations, the uphill and downhill yarding operations constituted 51% and 49%, respectively, of the total yarding operations. The productivity of the uphill yarding operation was 2.28 ㎥/h, and the productivity of the downhill yarding operation was 1.89 ㎥/h. The findings of this study revealedthat productivity would increase by 0.5 ㎥/h when the rate of utilization of the machine is increased to 80% by reducing the operational delay time. The cost of the downhill yarding operation was 44,116 KRW/㎥, whereas that of the uphill yarding operation was 53,369 KRW/㎥. The difference in cost resulted from the difference in the number of yarding stems (stems/cycle). Furthermore, the results of the multiple linear regression equation developed for predicting the yarding operation times showed that productivity was significantly affected by working conditions such as yarding distance (m), the number of stems per cycle (stems/cycle), and the terrain slope (%) in the uphill and downhill yarding operations. Further research is required for developing an accurate prediction model equation according to a yarding direction.