• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.204-205
• /
• 2014

Among common test methods of assessing structure safety for existing lightweight walls, the criteria of the quality assessment of the horizontal static load resistance has been considered ambiguous. In the current study, therefore, an experiment was conducted to figure out the standardized assessment criteria of the lightweight wall's horizontal static load resistance. Based on the findings of the experiment with gypsum board and ALC block walls, an acceptable amount of each standard and the variables of the stud wall arising from the appropriate load (1000N) on the wall in a daily life were accounted for, arbitrarily setting the maximum deformation amount below 15mm.

• 한국세라믹학회지
• /
• 제33권5호
• /
• pp.479-484
• /
• 1996

The tribological properties of ceramics are very important in the application to engineering ceramic parts such as mechanical seal slurry valve disc and so on. In this study the effect of graphite addition on the mechanical and tribological properties of RBSC/graphite composites were investigated. The composites were prepared by adding graphite powder to the mixture of SiC powder metallic siliconcarbon black and alumina. Bending strength water absorption friction coefficient the amount of worn out material at a certain time and maximum surface roughness(Rmax) of the prepared composites were measured and crystalline phases were examined with XRD. The composite containing 5 vol% graphite powder showed improved bending strength due to high green density and decreased friction coefficient and wear resistance. The friction coefficient and the wear resistance of the composite were increased by adding graphite powder up to 10 vol% They decreased however as increasing the amount of graphite powder more that 10vol% There was no linear relationship between the tribological properties and bending strength of the composites.

• 한국세라믹학회지
• /
• 제34권4호
• /
• pp.380-386
• /
• 1997

The tribological properties of ceramics are very important in the application to engineering ceramic parts such as seal rings, pump parts, thread guides, and so on. In this study, the effects of graphite addition on the mechanical and tribological properties of alumina/graphite composites were investigated. The composites were prepared by the adding of graphite powder to the mixture of Al2O3, talc and calcium carbonate. Bending strength, water absorption, friction coefficient, the amount of worn out material at a certain time, and maximum surface roughness(Rmax) of the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. The melt of Al2O3-CaO-MgO-SiO2 system was shown over 10 vol% graphite composition. As the amount of the graphite is increased, needle like crystals of mullite were formed and grown. We obtained the good properties of friction coefficients and wear resistance at the powder composition containing 15 vol% of graphite.

• 태양에너지
• /
• 제9권2호
• /
• pp.58-68
• /
• 1989

This paper describes an experimental study that was performed to determine the limiting factors on the power output in the closed cycle Electro-Hydro-Dynamic generator of small capacity. A corona discharge for producing unipolar charged particles used as the charging method. The experiment demonstrated that the corona method of charging was an efficient and effective means of producing unipolar charged particles. Four factors having an effect on the power output characteristics of EHD generator are discussed and examined experimentally, using methyl alcohol and kerosene as working fluides; a. The conversion length between attractor and collector. b. The corona current of Emitter. c. The flow velocity of working fluids. d. Load resistance. This results are as follows; 1) There in a critical value in conversion length for its maximum power output. 2) Power output increases almost linearly with corona current and flow velocity. 3) There is the critical value of load resistance producing a maximum power output. 4) Kerosene is known better working fluid than Methyl alcohol in this EHD generator.

• 센서학회지
• /
• 제21권3호
• /
• pp.172-179
• /
• 2012

This paper presents the design and analysis of a vibration-driven electromagnetic energy harvester that uses a multi-pole magnet. The physical backgrounds of the vibration electromagnetic energy harvester are reported, and an ANSYS finite element analysis simulation has been used to determine the different alignments of the magnetic pole array with their flux lines and density. The basic working principles for a single and multi-pole magnet are illustrated and the proposed harvester has been presented in a schematic diagram. Mechanical parameters such as input frequency, maximum displacement, number of coil turns, and load resistance have been analyzed to obtain an optimized output power for the harvester through theoretical study. The paper reports a maximum of 1.005 mW of power with a load resistance of $1.9k{\Omega}$ for 5 magnets with 450 coil turns.

• 센서학회지
• /
• 제20권1호
• /
• pp.25-29
• /
• 2011

This paper describes the design and analyses of vibration driven electromagnetic energy harvester with high power generation which is suitable for supplying power generator from human body motion. The proposed harvester consists of magnet, coil, and SM (Soft magnetic Material). In order to generate more induced voltage, the SM to concentrate flux lines from end of magnetic poles was arranged into insert moving magnet. Each model was designed and analyzed by using ANSYS software to simulation. The maximum power is generated when load resistance of $1303\;{\Omega}$ is equal to coil resistance. The generated maximum power of for harvesters with SM is $677.85\;{\mu}W$ and 5.46 times higher than without SM at 6 Hz vibration frequency.

• 대한전자공학회논문지
• /
• 제6권2호
• /
• pp.6-20
• /
• 1969

부저항소자인 턴넬다이오드와 수동선형부하로 부저항발진기를 구성하고 수동부하를 가변하여 주파수최대화에 관해서 연구했다. 이론적인 해석과 복소평면상의 임피이던스 궤적을 도시하고 병렬-RL부하와 저항부하의 두 경우의 최대발진주파수를 측정하여 두 경우의 실험결과를 보면 병렬-RL부하의 폭이 훨씬 높은 주파수를 발진하는 것을 알았다.

• 조명전기설비학회논문지
• /
• 제24권9호
• /
• pp.118-123
• /
• 2010

The selection of flux level in the maximum torque control of stator flux-oriented induction motor drives in the field weakening region is dependent on stator resistance and inductances. This paper presents parameter detuning effects of stator flux-oriented control drives in the field weakening region. The detuning effects of stator resistance and rotor leakage inductance are analyzed. The decrease of torque and the flux control lost by the detuning of inductance are shown in the simulation results.

• 한국전기전자재료학회논문지
• /
• 제31권7호
• /
• pp.481-485
• /
• 2018

In this study, oxide/metal/oxide-type transparent electrodes based on Al and ZnO were investigated. Thin films of these materials were sputter-deposited at room temperature. To evaluate the thickness dependence of the oxide layers, the top and bottom ZnO layers were varied in the range of 5~80 nm and 2.5~20 nm, respectively. When the thicknesses of the top and bottom ZnO layers were fixed at 30 nm and 2.5 nm, a maximum transmitance of 66% and sheet resistance of $16.5{\Omega}/{\square}$ were achieved, which is significantly improved compared with the Al layer without top and bottom ZnO layers showing a maximum transmitance of 44.3% and sheet resistance of $44{\Omega}/{\square}$.

• Smart Structures and Systems
• /
• 제26권3호
• /
• pp.311-318
• /
• 2020

The goal of this study is to analytically and non-stochastically generate structural uncertainty behaviors of isotropic beams and laminated composite plates under plane stress conditions by using an interval finite element method. Uncertainty parameters of structural properties considering resistance and load effect are formulated by interval arithmetic and then linked to the finite element method. Under plane stress state, the isotropic cantilever beam is modeled and the laminated composite plate is cross-ply lay-up [0/90]. Triangular shape with a clamped-free boundary condition is given as geometry. Through uncertainties of both Young's modulus for resistance and applied forces for load effect, the change of structural maximum deflection and maximum von-Mises stress are analyzed. Numerical applications verify the effective generation of structural behavior uncertainties through the non-stochastic approach using interval arithmetic and immediately the feasibility of the present method.