• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.366-376
• /
• 2008

The model tests of short pile with very small pile length/diameter(L/D) were performed in this paper. Varying the pile diameter, length, and the lateral loading point, the lateral resistance and behavior of very short pile were studied in this model tests. The experimental and analytical results are as follows. The lateral ultimate resistance of short pile in sands was the maximum at the point of h/L=0.75, regardless of pile length/diameter(L/D). As the pile diameter is larger, the lateral ultimate resistance of pile with L/D=1 decreases a little and the lateral resistance increases according to the ratio of pile length/diameter. As the lateral loads are acting on the pile, the displacement of pile head is maximum at the pile top of h/L=0, but minimum at the middle point of the pile. And if the loading point is under the middle of pile, the displacement of pile head occurs oposite in the loading direction, but its magnitude is very small.

• Journal of the Korean Wood Science and Technology
• /
• 제45권6호
• /
• pp.728-736
• /
• 2017

In this study, the bending behavior of cross-laminated timber (CLT) connected by nails were investigated. Especially, the load-carrying capacity of the nail-jointed CLT under out-of-plane bending was predicted by the lateral resistance of the used nails. Three-layer nail-jointed CLT specimens and a nail connection were manufactured by 30 mm (thickness) ${\times}$ 100 mm (width) domestic species (Pinus koraiensis) laminas and Ø$3.15{\times}82mm$ nails using a nail-gun. Shear test for evaluating the nail lateral resistance and bending test for evaluating the load-carrying capacity of the nail-jointed CLT under out-of-plane bending were carried out. As a result, two lateral resistance of the used nail, the 5% fastener offset value and the maximum value, were 913 N and 1,534 N, respectively. The predicted load-carrying capacity of the nail-jointed CLT by the 5% offset nail lateral resistance was similar to the yield points on the actual load-displacement curve of the nail-jointed CLT specimens. Meanwhile, the nail-jointed CLT specimens were not failed until the tension failure of the bottom laminas occurred beyond the maximum lateral resistance of the nails. Thus, the measured maximum load carrying capacities of the nail-jointed CLT specimens, approximately 12,865 N, were higher than the predicted values, 7,986 N, by the maximum nail lateral resistance. This indicates that the predicted load-carrying capacity can be used for designing a structural unit such as floor, wall and roof able to support vertical loads in a viewpoint of predicting the actual capacities more safely.

• 대한물리치료과학회지
• /
• 제11권1호
• /
• pp.14-19
• /
• 2004

Objective : This study obtained normative values for variable parameters of lumbar function with the isoinertial triaxial dynamometer in patients with chronic low back pain. Subjects and Methods : 30 patients(male 15, female 15) with chronic low back pain in this study. Variable parameters that were measured with the Isostation B-200 were lumbar range of motion, isometric maximum torques, and maximum velocities in three axis. Results : In patient male group mean R.O.M. was $82.9{\pm}12.5$ degrees in lumbar rotation, $76.5{\pm}17.1$ degrees in lumbar flexion/extension, and $64.3{\pm}14.5$ degrees in lumbar lateral flexion. In patient female group mean R.O.M. was $78.4{\pm}18.5$ degrees in lumbar rotation, $71.7{\pm}20.4$ degrees in lumbar flexion/extension, and $63.2{\pm}14.4$ degrees in lumbar lateral flexion. In patient male group mean isometric maximum torques was $64.7{\pm}23.8ft-lbs$ in lumbar rotation, $81.1{\pm}42.0ft-lbs$ in lumbar flexion, $122.2{\pm}43.6ft-lbs$ in lumbar extension, and $101.0{\pm}37.0ft-lbs$ in lumbar lateral flexion. In patient female group mean isometric maximum torques was $41.9{\pm}9.2ft-lbs$ in lumbar rotation, $49.9{\pm}23.9ft-lbs$ in lumbar flexion, $90.1{\pm}26.8ft-lbs$ in lumbar extension, and $62.0{\pm}16.7ft-lbs$ in lumbar lateral flexion. In patient male group mean maximum velocity of isoinertial exercise with low (25%) resistance was $102.4{\pm}28.8deg/sec$ in lumbar rotation, $108.9{\pm}32.2deg/sec$ in lumbar flexion/extension, and $103.5{\pm}30.4deg/sec$ in lumbar lateral flexion. In patient female group mean maximum velocity of isoinertial exercise with low (25%) resistance was $84.1{\pm}24.4deg/sec$ in lumbar rotation, $93.2{\pm}32.9deg/sec$ in lumbar flexion/extension, and $98.5{\pm}33.7deg/sec$ in lumbar lateral flexion. In patient male group mean maximum velocity of isoinertial exercise with high (50%) resistance was $74.0{\pm}20.9deg/sec$ in lumbar rotation, $98.7{\pm}32.8deg/sec$ in lumbar flexion/extension, and $85.0{\pm}25.8deg/sec$ in lumbar lateral flexion. In patient female group mean maximum velocity of isoinertial exercise with high (50%) resistance was $67.3{\pm}26.4deg/sec$ in lumbar rotation, $82.5{\pm}31.0deg/sec$ in lumbar flexion/extension, and $79.7{\pm}23.9deg/sec$ in lumbar lateral flexion. Conclusion : Maximum isoinertial velocities were more reliable and more significant than isometric maximum torque for the objective assessment of chronic low hack pain.

• 한국지반공학회논문집
• /
• 제33권9호
• /
• pp.49-60
• /
• 2017

본 연구는 모형시험을 통해 반복수평하중이 작용하는 단일경사말뚝의 거동 특성을 파악하고자 한다. 반복하중은 일방향과 양방향으로 작용 시켰으며, 지반의 상대밀도를 달리하여 수평저항력과 휨모멘트의 변화 등을 분석하였다. 그 결과, 일방향 및 양방향 반복수평하중이 작용할 경우 Out batter, Plumb, In batter 순으로 수평저항력과 최대 휨모멘트는 증가하였다. 최대 휨모멘트 발생위치는 일방향 보다 양방향 반복수평하중을 가할 때 조금 더 깊은 곳에서 나타났다. 또한, 상층의 모멘트는 Out batter, Plumb, In batter 순으로 모멘트가 증가하나 하층의 경우 Out batter, Plumb, In batter 순으로 감소하였고 일방향에 비해 양방향 반복수평하중이 작용할 때 상 하층의 모멘트 변화가 작게 나타났다.

• 한국지반신소재학회논문집
• /
• 제20권4호
• /
• pp.95-103
• /
• 2021

기존의 말뚝기초는 상부구조물을 지지하거나, 토압을 감소시키는 역할이었다면, 최근에는 상부구조물과 일체화되어 수평저항력을 높이는 사례들이 있다. 따라서, 본 연구는 여러 개의 말뚝으로 보강된 블록 형식의 방파제에 대해 실내모형실험을 수행하였고, 수평저항력을 평가하였다. 실험에서는 말뚝이 근입된 깊이를 변화시켜 말뚝의 수평저항력과 말뚝의 위치별 휨모멘트를 측정하였다. 그 결과 무리말뚝의 근입깊이가 깊어짐에 따라 수평저항력이 커짐을 알 수 있었다. 특히 사석층까지 무리말뚝이 관입된 경우가 블록내에 관입된 경우보다 수평저항력이 1.52배 크게 나타났다. 휨모멘트의 경우 후열말뚝이 전열말뚝보다 크게, 바깥쪽 말뚝이 안쪽 말뚝보다 크게 나타났다. 지반내에서 최대 휨모멘트의 발생 위치는 사석층과 원지반의 경계면에서 나타났다.

• 한국도로학회논문집
• /
• 제19권1호
• /
• pp.21-28
• /
• 2017

PURPOSES : This paper presents a finite element model to accurately represent the soil-post interaction of single guardrail posts in sloping ground. In this study, the maximum lateral resistance of a guardrail post has been investigated under static and dynamic loadings, with respect given to several parameters including post shape, embedment depth, ground inclination, and embedment location of the steel post. METHODS : Because current analytical methods applied to horizontal ground, including Winkler's elastic spring model and the p-y curve method, cannot be directly applied to sloping ground, it is necessary to seek an alternative 3-D finite element model. For this purpose, a 3D FHWA soil model for road-base soils, as constructed using LS-DYNA, has been adopted to estimate the dynamic behavior of single guardrail posts using the pendulum drop test. RESULTS : For a laterally loaded guardrail post near slopes under static and dynamic loadings, the maximum lateral resistance of a guardrail post has been found to be reduced by approximately 12% and 13% relative to the static analysis and pendulum testing, respectively, due to the effects of ground inclination. CONCLUSIONS : It is expected that the proposed soil material model can be applied to guardrail systems installed near slopes.

• 대한건축학회논문집:구조계
• /
• 제36권5호
• /
• pp.137-146
• /
• 2020

In this study, an experimental research was performed to find the characteristics of the lateral load resistance of perforated steel plates which could be developed to retrofit existing RC framed buildings. The Specimens are tested with variables such as aspect ratio of plate, the ratio of perforation area, and the ratio of perforated diameter to strip which is more than 0.6. The lateral load was applied with displacement control until to reach 3.5% drift ratio. Through the experimental results, it was shown that the maximum strength of all specimens were reached at around 0.5% drift ratio and maintained until 3.5% drift ratio. From results, the modified strength prediction formula was derived with the variable ratio of the perforated diameter to strip. To evaluate seismic retrofit performance of RC frames using perforated steel plate, a simple design process was presented.

• 한국지반신소재학회논문집
• /
• 제21권2호
• /
• pp.49-56
• /
• 2022

본 연구는 말뚝으로 보강된 풍력발전기초의 수평저항력을 실내모형실험을 통해 구하였다. 특히 말뚝과 풍력발전기초 및 암반지반을 일체화시켜 기존의 중력식 풍력발전기초와의 수평저항력을 비교하였다. 또한 말뚝의 근입깊이를 달리하여 말뚝의 수평저항력 및 휨모멘트의 변화를 분석하였다. 그 결과 말뚝의 근입깊이가 깊어짐에 따라 수평저항력이 커짐을 알 수 있었다. 특히 암석층까지 말뚝이 근입된 경우가 사석층까지 근입된 경우보다 말뚝의 저항력 증가비가 2.11배 크게 나타났다. 말뚝이 암반지반까지 근입될 경우 최대 휨모멘트의 발생위치는 풍력발전기초와 사석층의 경계면에서 나타남을 알 수 있었다. 이를 통해 기존 중력식 풍력발전 기초보다 말뚝으로 보강된 풍력발전 기초의 수평저항력이 크게 나타남에 따라 안전성 측면에서 더 유리한 시공방법이 될 수 있을 것으로 파악된다.

• Journal of the Korean Wood Science and Technology
• /
• 제41권3호
• /
• pp.211-220
• /
• 2013

경골목조건축에서 못 접합부는 수평하중을 지지하고 전달하도록 설계되지만, 바람으로 인한 상향력처럼 인발하중에 직면하기도 한다. 본 연구에서는 경골목조건축에서 일반적으로 사용되는 구조재와 덮개로 구성된 못 접합부에 대하여 인발성능과 2면 전단시험을 통해 인발 및 측방하중에 대한 내력성능을 시험하고 설계기준에 부합되는 가를 평가하였다. 인발하중에 대한 내력성능은 부재의 비중에 의해 크게 좌우되었으며 I형장선의 경우 낮은 밀도에도 불구하고 높은 인발성능을 나타내었다. 최대 인발하중은 기준허용 최대 인발하중보다 매우 높게 나타났다. 전단성능도 비중이 큰 낙엽송과 오에스비로 구성된 접합부가 비중이 작은 SPF와 오에스비로 구성된 접합부보다 높은 성능을 나타내었으며 모두 기준설계치보다 높은 성능을 나타내었다. 접합부의 변형은 주로 못의 휨 변형에 의한 것으로 나타났으며 SPF와 오에스비로 구성된 접합부에서의 못의 휨 변형이 현저하게 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• 제47권5호
• /
• pp.547-556
• /
• 2019

Thinned, small larch logs have small diameters and no value-added final use, except as wood chips, pallets, or fuel wood, which are products with very low economic value; however, their mechanical strength is suitable for structural applications. In this study, small larch logs were sawed, dried, and cut into square timbers (with a $90mm{\times}90mm$ cross section) that were laterally glued to form core panels used to manufacture cross-laminated timber (CLT) wall panels. The surface and back of these core panels were covered with 12-mm-thick structural plywood panels, used as cross bands to obtain three-ply CLT wall panels. This attachment procedure was conducted in two different ways: gluing and pressing (CGCLT) or gluing and nailing (NGCLT). The size of the as-manufactured CLT panels was $1,220mm{\times}2,440mm$, the same as that of the plywood panels. The final wall panels were tested under lateral shear force in accordance with KS F 2154. As the lateral load resistance test required $2,440mm{\times}2,440mm$ specimens, two CLT wall panels had to be attached in parallel. In addition, the final CLT panels had tongued and grooved edges to allow parallel joints between adjacent pieces. For comparison, conventional light-frame timber shear walls and midply wall systems were also tested under the same conditions. Shear walls with edge nail spacing of 150 mm and 100 mm, the midply wall system, and the fabricated CGCLT and NGCLT wall panels exhibited maximum lateral resistances of 6.1 kN/m (100%), 9.7 kN/m (158%), 16.9 kN/m (274%), 29.6 kN/m (482%), and 35.8 kN/m (582%), respectively.