• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.171-173
• /
• 2002

This paper describes the open frame type high power density switching converter. It is based on active clamp forward converter with synchronous rectifier, and packaged by using the open frame and multi-layer printed circuit board (PCB) techniques to achieve the high power density. Furthermore, windings of transformer and inductor are also realized by multi-layer PCB so that it achieves the higher power density. Through the experiment on the proto-type converter of 50[W], it is confirmed that power density of $50[W/in^3]$ and maximum efficiency of over 91 [%] are obtained.

• 한국표면공학회지
• /
• 제30권1호
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.792-797
• /
• 2009

The stress-strain characteristics of compacted bentonite are investigated using experimental triaxial compression test by Hoek-cell. Special attention given to various dry density and water absorption ratio. Based on the test results, it is shown that the stress-strain relationship of compacted bentonite is highly influenced by dry density and water absorption ratio. Also, characteristics of Bentonite is similar to the clay rather than sand. Strength of compressed Bentonite increases with higher dry density. It shows maximum strength value, if in a same condition with dry density and constrain pressure. So we determine that value as the optimistic moisture contents for the maximun strength of compressed Bentonite.

• Wind and Structures
• /
• 제2권2호
• /
• pp.105-117
• /
• 1999

The various spectral density functions of wind are applied in the wind process simulation by the spectral representation method. In view of the spectral density functions, the characteristics of the simulated processes are compared. The ensemble spectral density functions constructed from the simulated sample processes are revealed to have the similarity not only in global shape but also in the maximum values with the target spectral density functions with a high accuracy. For the correlation structure to be satisfied in the circumferential direction on the cooling tower shell, a new formula is suggested based on the mathematical expression representing the circumferential distribution of the wind pressure on the cooling tower shell. The simulated wind processes are applied in the dynamic analysis of cooling tower shell in the time domain and the fluctuating stochastic behavior of the cooling tower shell is investigated.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1243-1244
• /
• 2006

Five kinds of double stacked 385 (55 x7) filamentary Bi2212/Ag round wires and 55 filamentary tapes with different Ag ratios (silver area/superconductor area) have been fabricated via PIT method, and the effects of Ag ratio and processing factors on critical current density were studied. The effects of the maximum temperature and average filament diameter on critical current density were also studied. The wire of 0.74 mm diameter having Ag ratio 3.7 showed critical current density of $2,218\;A/mm^2$ at 4.2 K, 0 T.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.912-920
• /
• 2006

The purpose of this study is to present the design standard for load density in subway station. From the data of electric equipment capacity and electric power consumption for 43 subway stations, current levels of the load density and excess capacity factor were surveyed and analyzed, In addition mean value, standard deviation, maximum value, median value and correlation coefficient were evaluated through excel program. Also it was carried out the regression analysis. The estimation method of load density and design criterion were studied. As a result, load density in this thesis have been proposed : 51.3 $[VA/m^2]$ on the general power load can be a standard value for subway station.

• Journal of the Korean Wood Science and Technology
• /
• 제39권1호
• /
• pp.60-67
• /
• 2011

본 연구에서는 고밀도 우드세라믹을 제조하기 위한 기초 연구로서 수지함침율 및 탄화온도에 따라 제조된 1차 탄화 우드세라믹을 수지 재 함침 후 2차 탄화하여 우드세라믹을 제조하고 밀도경사를 조사하였다. 2차 탄화 후 최소, 평균 및 최고밀도가 1차 탄화 우드세라믹보다 증가하였고, 밀도경사 비율도 증가하였다. 따라서 고밀도와 밀도경사 비율이 작은 균질한 우드세라믹을 제조하기 위해서는 2차 함침과 2차 탄화에 의한 우드세라믹 제조방법도 효과가 있는 것으로 나타났다.

• Nuclear Engineering and Technology
• /
• 제56권7호
• /
• pp.2452-2457
• /
• 2024

To obtain site-specific values of the Derived Concentration Guideline Levels (DCGLs) for decommissioning of KRR-1&2, the soil density and distribution coefficient values for Cs-137, a major contaminant radionuclide, were determined. The soil density was evaluated according to the test method established by the Korean Agency for Technology and Standards of the Ministry of Trade, Industry, and Energy (KATS). The distribution coefficient was evaluated using a batch test. The validity of using the evaluated soil density and distribution coefficient as site-specific values was assessed through radiation dose assessment reflecting these values. Average soil density value obtained was 1.738 g/cm³, which was within the typical range of normal soil density, 1.0-1.8 g/cm³. The average distribution coefficient value was 7,754 mL/g. Applying the maximum, average, and minimum values of the evaluated soil density and distribution coefficient showed similar radiation dose results, thus suggesting that it is reasonable to use the average values of each parameter as site-specific values. Findings of this study can help determine DCGLs that reflect the characteristics of the research reactor site.

• 한국조경학회지
• /
• 제15권2호
• /
• pp.79-90
• /
• 1987

This second consecutive research was connected to 7he previous first research with same title. The purpose of this research is to estimate the carrying capacity for the Seonjeong royal tomb and to propose its management planning. User's characteristics and relationship between user's density and vegetational environment were analized for the above objective. The result of this research shall be summarized as follows. 1. The site was damaged seriously by pupils and social groups'picnic activities concentrated in special periods of Friday and weekend during April and May. 2. Social-psychological carrying capacity estimation would be impossible due to lack of relationship between user's density and satisfaction. 3. Maximum user's density limits as a ecological carrying capacity was 1.4 persons per 100 square meters and modified optimum ecological carrying capacity was estimated as 1.0persons per 100 square meters. Maximum visitors as a optimum carrying capacity of the Seonjeong royal tomb area was estimated as 6,000 persons when supposing the proposed landuse planning. 4. To restore and preserve the tomb landscape as a traditional historic site, Seonjeong royal tomb shall be managed by three landuse areas ; protection and control area, natural picnic area and shaded picnic area. And the protection and control area include three sites ; natural reclamation site, natural preservation site and tomb landscape conservation site.

• Applied Biological Chemistry
• /
• 제40권1호
• /
• pp.18-22
• /
• 1997

Bifidobacterium longum을 고농도 배양하기 위하여 최적 생육 조건을 조사하고 cross-flow filtration으로 생육 저해 대사산물인 lactic acid와 acetic acid를 제거하면서 균체 순환 배양을 사용하였다. 회분 배양에서는 탄소원으로 glucose를 50 g/l 농도로 사용하고 초기 pH 6.5인 경우 생육이 가장 높았다. B. longum을 cross-flow filtration으로 12시간 배양한 결과, 희석속도 $0.31h^{-1}$에서 최대 균체농도에 도달하여 16.4g/l의 건조균체량을 얻었으며 이로써 회분 배양시 보다 약 4배 높은 균체를 생산하였다.