• Fashion & Textile Research Journal
• /
• v.10 no.3
• /
• pp.329-334
• /
• 2008

The purpose of this research is to develop the design, pattern and size system of brief as a measurement garment in order to obtain more precise silhouettes and sizes of the body in 3D measurements. The results of this research are as follows: First, nylon/lycra materials which elasticity is equivalent to 18%(wale) and 27%(course), were selected as a material for briefs to minimize possible error in measurement and deformation of body shape caused by looseness or tightness in its measured parts. And T-back style design was selected, of which briefs neither deform human body nor cause overlapping or excessive tightness when was put on the measurement garment over it. Second, different darts for men and women were adopted into the pattern in consideration for the shape of hip. Third, the waist band of briefs was located between the waistline and abdominal girth line so that it didn't interfere with measurement, and using a wide band of 40mm minimized the tightness of the human body. In addition, the stitch lines and sewing procedure were simplified to minimize the deformation of body shape resulting from inseams and stitch lines. Finally, for the size of briefs, 6 cm intervals were set on the basis of the waist girth and 8 kinds for men and 6 kinds for women were selected in descending order of appearance rate by the interval sections. English T meaning T-back design and numbers representing the waist girth were marked in parallel for the name of size.

• Elastomers and Composites
• /
• v.55 no.2
• /
• pp.81-87
• /
• 2020

Service life prediction and evaluation of rubber components is the foundational technology necessary for securing the safety and reliability of the product and to ensure an optimum design. Even though the domestic industry has recognized the importance thereof, technology for a systematic design and analysis of the same has not yet been established. In order to develop this technology, identifying the fatigue damage parameters that affect service life is imperative. Most anti-vibration rubber components had been damaged by repeated load and aging. Hence, the evaluation of the fatigue characteristics is indispensable. Therefore, in this paper, we propose a method that can predict the service life of rubber components relatively accurately in a short period of time. This method works even in the initial designing stage. We followed the service life prediction procedure of the proposed rubber components. The weak part of the rubber and the maximum strain were analyzed using finite element analysis of the rubber bushing for the tracked vehicles. In order to predict the service life of the rubber components that were in storage for a certain period of time, the fatigue test was performed on the three-dimensional dumbbell specimen, based on the results obtained by the rubber material acceleration test. The service life formula of the rubber bushing for tracked vehicles was derived using both finite element analysis and the fatigue test. The service life of the rubber bushing for tracked vehicles was estimated to be about 1.7 million cycles at room temperature (initial stage) and about 400,000 cycles when kept in storage for 3 years. Through this paper, the service life for various rubber parts is expected be predicted and evaluated. This will contribute to improving the durability and reliability of rubber components.

• Journal of Welding and Joining
• /
• v.26 no.5
• /
• pp.49-59
• /
• 2008

Hastelloy C-276, corrosion resistant alloy at high temperature, is used in chemical plant and power generation industry. In this study, process parameter of laser welding for welding property in Hastelloy C-276 using a continuous wave Nd:YAG laser was studied. As the result of experiment, laser welding did not show segregation or crack at heat affected zone compared to conventional GTWA welding. The melting zone showed cell dendritic structure along with welding line. In addition, planer front solidification is occurred from welding structure, and it was progressed to cellular solidification. Optimal process parameter for butt welding was 1.2kW and 2.0 m/min for laser power and welding speed, respectively. While heat input, output density, tensile stress, and longitudinal strain was $441.98{\times}103$ J/cm2, $29.553{\times}103$ W/cm2, 768 MPa, and 0.689, respectively. Lap welding of the same material showed greater discrepancy in tensile property during 1 line and 2 line welding. For 1 line welding, tensile stress was about 320 MPa, and 2 line showed slightly larger tensile stress. However, strain was decreased by 20%. From this result, lap welding of the same material, Hastelloy C-276, with 2 line welding is considered to be more effective process than 1 line welding with consideration of mechanical property.

• Journal of Korean Society for Quality Management
• /
• v.49 no.2
• /
• pp.113-125
• /
• 2021

Purpose: This study focused on reality and quality improvement of aviation security equipment performance certification system. Methods: For this propose, we analyzed aviation security equipment performance certification system related legislations. Using analyzed data, we suggested advancement plan of aviation security equipment performance certification system. Results: In results, South Korea has been implementing aviation security performance certification system since October 2018. Parts for improvement of system are mutual certification with major countries that operate aviation security equipment performance certification systems, the spread of the defense industry's system, development of similar substances for handling explosives, and introduction of preliminary inspections. Conclusion: The research result could be used as a basic data for upgrading Korea's aviation security performance certification system.

• Resources Recycling
• /
• v.20 no.3
• /
• pp.12-27
• /
• 2011

DOWA group has been working on metal recycling applying the smelting and refining process of KOSAKA Smelter. DOWA has developed it's metal recycling technologies through the treatment of black ore(complex sulfide ores) that contain many kinds of non-ferrous metals. In addition to these special technologies, DOWA has strengthened its hydrometallurgical process of precious metals and ability to deal with low-grade materials such as used electrical appliances or vehicles. On the other hand, JX Nippon Mining & Metals Corporation(JX-NMMC) carries out its metal recycling and industrial waste treatment businesses employing advanced separation, extraction and refining technologies developed through its extensive experience in the smelting of non-ferrous metals. JX-NMMC collects approximately 100,000t/y of copper and precious metal scraps from waste sources such as electronic parts, mobile phones, catalytic converters, print circuit boards and gold plated parts. These items are recycled through the smelting and refining operations of Saganoseki smelter and Hitachi Metal-recycling complex(HMC). In this like, metal recycling industries combined with environmental business service in Japan have been developed through excellent technologies for mineral processing and non-ferrous smelting. Also, both group, Dowa and JX-NMMC, were contributed to establish Japan's recycling-oriented society as the typical leading company of non-ferrous smelting. Now. it is an important issue to set up the collection system for e-waste.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.11a
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.

• Cartoon and Animation Studies
• /
• s.48
• /
• pp.311-332
• /
• 2017

Currently, the world is making efforts to develop cultural industries around more refined parts of the world. The development of cultural industries has far-reaching implications for promoting national brands and national image promotion as well as economic benefits. In particular, China hopes to advance into its own animation market because it has an extensive animation market. In 2005 The Chinese government, however, banned foreign animation market from entering the Chinese animation market. However, at that time, Chinese animation firms also saw considerable economic losses because they had to undergo almost everything from animation to distribution to rationing. In fact, the policy was designed to protect Chinese animations, but instead of preventing Chinese animations from developing original contents, it caused various problems such as China's animations, or the development of Chinese animation industries. In this thesis, we will explore the policy related to animation industry in China, research and development of animation industry, and establish the direction of development of Chinese animation industry through suggestion of improvement in Chinese animation industry. For starters, we have diversified the contents of the Chinese animation industry by adapting the contents of the Chinese animation to the global market through the globalization of contents, stories and materials. Currently, animation is developing beyond 3D,4D and VR but there is no shortage of animation experts in China, so it is necessary to nurture specialized professionals by opening a related department in China. Also, the government will establish a National Animation Industry complex to work in various animation companies. We expect to develop cultural contents through mutual cooperation between animation companies in China and the sharing of information sharing and collaborative research.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.17 no.2
• /
• pp.155-172
• /
• 2015

This study analyzed the change pattern of Korean male body size in their 40s-60s and their current body shape based on the research materials of the 5th(2004) and 6th(2010) conducted by Size Korea. The purposes of this study are to make the related fashion industry recognize the changes of Korean male body size in their 40s-60s and suggest basic materials for clothing design that reflects such trend. As a result of analyzing changes of male body size in their 40s-60s by age, it was found that height, length, breadth and weight decreased across most of the items as the age increased. As for circumference, as the age increased, waist circumference (natural indentation), waist circumference (omphalion), and abdominal extension circumference increased, while other items decreased. In relation to the depth, as the age increased, hip depth and armscye depth decreased, while chest depth, bust depth, waist depth (natural indentation), and waist depth (omphalion) increased. Analyzing the change pattern of Korean male body size in their 40s-60s according to measurement year, height size increased in the 6th year across most of the body part items compared to the 5th year. It means that height of body parts related to body height increased in overall. As for circumference, most items showed decrease, which means that Korean male's body shape in their 40s-60s gets slim gradually. While the breadth of the chest decreased, the depth of the chest increased. which is assumed due to the increase in exercise according to high interest in health in a society. It will be possible to design proper clothes for consumer body type and trends if we design clothes that afford multilateral attention to the patterns, design, or material in clothing design by applying the aspects of Korean male body size in their 40s-60s and body type change.

• The Korean Journal of Malacology
• /
• v.30 no.4
• /
• pp.321-331
• /
• 2014

Patinopecten yessoensis is known to be farmed only in the northern part of the East Sea today. In an attempt to extend its production area, we have conducted experiments both in the northern and southern parts of the East Sea and studied on their growth in an aim to use the results for increasing overall productivity of the species. Early juvenile scallops producted in February 2014 showed an average shell length of $0.23{\pm}0.002$. The high growth group showed an average shell length and shell height of $4.11{\pm}0.08mm$ and $4.28{\pm}0.09mm$, respectively, in June while they were $23.63{\pm}3.4mm$ and $24.19{\pm}4.5mm$ in October. The low growth group showed an average shell length and shell height of $2.23{\pm}0.7mm$ and $1.99{\pm}0.9mm$, respectively, in June while they were $1.99{\pm}0.9mm$ and $17.59{\pm}4.5mm$ in October. The daily growth rate of the high growth group was 0.037 mm/day and 0.027 mm/day for the low growth group. In August, we measured the shell length of Patinopecten yessoensis from Yangyang-gun, Gangneung-si, Yeongdeok-gun, and Pohang-si. Patinopecten yessoensis from Pohang-si showed the best growth performance with its shell length of $26.90{\pm}3.6mm$. Patinopecten yessoensis from Yeongdeok was the second largest with its shell length of $23.56{\pm}3.4mm$. We presume that optimal water temperature and phytoplankton abundance of the two regions have contributed to the good growth performance of the species.

• Food Engineering Progress
• /
• v.15 no.2
• /
• pp.130-135
• /
• 2011

Acanthopanax sessiliflorus (A. sessiliflorus) has been known as a traditional medicine having anti-stress, antioxidative and platelet aggregation inhibitory effects. This study was undertaken to investigate the functional properties of water extracts from four parts of A. sessiliflorus. Root, stem, leaf and fruit extracts from A. sessiliflorus were prepared with hot water ($80^{\circ}C$). The contents of functional substances, eleutheroside B and E, polyphenol, antioxidative activity, nitrite scavenging ability and anti-cancer activity of the extracts were determined. The contents of eleutheroside E in stem, root and fruit extracts were 542.50 ${\mu}$g/g, 343.35 ${\mu}$g/g and 30.78 ${\mu}$g/g, respectively. A large part of eleutheroside B was found in fruit (372.01 ${\mu}$g/g) and root (289.33 ${\mu}$g/g) extracts. Root and stem extracts contained 227.21 mg/100g and 131.22 mg/100g of polyphenols, respectively. Antioxidative activities (electron donating ability) of stem and root extracts were 79.87% and 77.27%, respectively. It appears that the antioxidative activities were related to polyphenol contents of the extracts. Most extracts showed 76-81.5% of nitrite scavenging ability at pH 1.2. It reveals that water extract from parts of A. sessiliflorus can inhibit formation of nitrosoamine in food. Effects of the extracts on the growth of normal and cancer cell lines were investigated. Extracts showed no cytotoxicity to normal dendritic cell line (DC2.4). Especially, the root extract promoted the growth of normal cell line. Root and stem extracts had 20-23% of inhibitory effect against stomach cancer cell line (SNU-719) and liver cancer cell line (Hep3B). These result indicated that the extracts from A. sessiliflorus can be used as functional food materials with antioxidative activity and nitrite scavenging ability to eliminate nitrosoamine in food.