• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.13 no.1
• /
• pp.57-68
• /
• 2010

The purpose of this study is to analyze the characteristics of environment-friendliness of waterproof materials based on comprehensive experiments on waterproofness in terms of coefficients of permeability, harmfulness of waterproof materials and fish toxicity of Oryzias latipes mortality to verify eco-toxicity of each method of construction and waterproof material, which are to be applied by taking eco-toxicity into account when building ecological flows in upper areas on natural and artificial grounds. As a result, the following conclusions have been reached in this study: 1. In regard of the harmfulness analyzed, each material showed a different result of analytical value in each lab tank. Compared to input water, pH, COD, SS, T-P, and T-N values increased a little, but DO value decreased. The value of turbidity analyzed independent of the water quality standard of aquatic ecosystem set forth by the Ministry of Environment increased a little compared to the value in input water. 2. In the experiment of fish toxicity, compacted quicklime, cement fluid waterproof material, cement mortar waterproof material and bentonite powder were found to have 100% of fish mortality, respectively, and membrane waterproof material showed 83.3% of mortality, indicating strong fish toxicity. Improved asphalt sheet (63.3%) and synthetic rubber sheet (53.3%) were analyzed to have medium fish toxicity, while bentonite sheet (6.7%), Hwang-toh (6.7%) and clay (3.3%) showed relatively lower mortality and fish toxicity. 3. Regarding the analysis on waterproofness in terms of the coefficient of permeability of each waterproof material, improved asphalt sheet, synthetic rubber sheet, membrane waterproof material, cement fluid and mortar waterproof material and bentonite sheet were found impervious in case no leakage takes place in construction. Bentonite powder was found practically impervious based on the analytical results from the experiment done in compliance with weight ratios. So were the clay and Hwang-toh from the experimental results. To sum up such results as found in the experiment mentioned so far, the values of harmfulness and waterproofness analyzed were different in each lab tank, but there was absolutely little correlation with the mortality gained from the experiment on fish toxicity. In the experiment of fish toxicity, environment-friendly waterproof materials were analyzed, and it was found that clay, Hwang-toh and bentonite sheet are highly environment-friendly. In contrast, synthetic rubber and improved asphalt sheets were found to have medium-level environment-friendliness. Also, membrane water-proof materials, compacted quicklime, cement fluid and mortar waterproof material and bentonite powder were analyzed to have low environment-friendliness.

• Journal of Families and Better Life
• /
• v.15 no.1
• /
• pp.111-128
• /
• 1997

This study mainly deals with the housewife's value orientation home management strategy and home management satisfaction,. The major results are as follows; 1) The degree of communication and communication frequency in household prove the predictable variables to influence the housewife's value orientation home management strategy and home management satisfaction. 2) Among the value orientation fate control orientation predicts home management strategy. 3) Material orientation shows the negative influence on her home management satisfaction. 4) Among home management strategy the fact that household financial management strategy and housework organization strategy are the important variables in the home management satisfaction suggest that household financial management and everyday repeated housework management cause the deep influence on her life satisfaction. 5) The higher her material orientation and gender equilibrium orientation are the higher housework socialization stra egy frequency is the lower her home management satisfaction is.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1275-1275
• /
• 2001

The pH value of grass silages is one important parameter to determine the quality of the forages. In an attempt to use NIRS spectra taken for other quality parameter of grass silage it has been shown that a good correlation between NIR spectra of the dried forage and pH value of the fresh forage could be determined. Further investigations revealed that the B coefficients of the pH value calibration were almost the same as the B coefficients of the sugar calibration multiplied with -1. And indead the pH value - in the fresh sample material - of the calibration set is strongly correlated with the sugar concentration - in the dried sample material. It is concluded that next to scientific tools in research the scientist and the user of NTRS equippment has to scrutinze his own work. Examples are given. NIRS is a powerfull technique, but pitfalls are present in surplus.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.322-325
• /
• 2000

In the previous report1), the grinding characteristics of quartz were investigated. In this paper, the grinding mechanisms of brittle materials including ceramics and quartz are modeled and a new parameter SDR(Surface roughness Direction Ratio) is proposed to characterize the grinding mechanisms of such materials. A set of experiments were performed to verify the effectiveness of the suggested parameter. The experimental results indicate that the plastic deformation is the dominant material removal mode at the grinding conditions which show the higher value of SDR. In the case of quartz, the material was removed by brittle fracture in a lower value of SDR and by plastic deformation in a higher value of it. SDR is not affected by wheel mesh size when brittle fracture occured. But in the plastic deformation case, SDR value increases with wheel mesh size.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.4
• /
• pp.126-136
• /
• 2003

The B value on the saturated soil is commonly known as the amount of 1. Usually this concept is consistent with the condition that effective stress is equal to zero, but it was reported in some literatures that the B value was less than 1 in spite of saturated condition in the test of very stiff material such as rock and quasi-stiff material on which the stiffness can be mobilized because of effective stress not equal to zero. In this study the B value was measured on various effective stress conditions on normally consolidated clay. The test results in the B value less than 1 in spite of perfect saturation. The measured excessive pore water pressure was not only smaller than the change of the total stress, but also the function of time on clay.

• Journal of Family Resource Management and Policy Review
• /
• v.3 no.2
• /
• pp.33-50
• /
• 1999

The purpose of this study is to analyze the relationship of housewives’sense of ancestral service and behavior and to verify the how housewives’value orientation affects the sense of ancestral service and behavior. The data are collected from 393 housewives in urban. The statistics used for the analysis are Cronbach’$\alpha$, Frequency, Percentage, Mean, SD, and Multiple Regression Analysis. The results are summarized below: First, among the variables, degree of fate-control orientation is the most, on the contrary, material orientation is the lowest. Second, value orientation variables that affect sense and behavior of ancestral service are material orientation and gender equilibrium orientation. Third, the behavior of ancestral service is more traditional than sense of ancestral service. Fourth, cause-and-effect variable which affect behavior of ancestral service are education level, religion(Buddhism, Catholicism), employment status, number of children, health, daughter in -law’s ranking, sense of ancestral service, and value orientation, which affect the direct or direct and indirectly. Especially sense of ancestral service variable is the most important mediation one. We expect further studies on the sense of ancestral service and behavior with precise scale and sampling.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.164-164
• /
• 2009

This paper had analyzed property of LED chip which has appropriate distribution and had designed modeling in order to experiment optical property of LED module through simulation. also throughout error value between street light and simulation data, precisive simulation could be inferred. as a consequent, transformation of optical property had henceforth verified the first value of module array.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.202-206
• /
• 2001

The purpose of this research was to study the influence of machining characteristics for aluminum alloys. The effect of metallic microstructural variables on the measures of machinability of aluminum alloys has no been adequately investigated. Machining Characteristics are influenced significantly by mechanical characteristics, composition and structure of material etcs. For improvement of machining characteristics, various studies are reported. In this paper, composition elements add to aluminum alloys within the limit of sustaining mechanical characteristics of metallic material. We have analyzed dynamic characteristics of cutting resistance, tensile strength value, hardness value etcs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.135-138
• /
• 1995

This paper presents a method to calculate the escape frequency factor and its verification from TSC(Thermally Stimulated Current) equation and cures. To apply calculation method of ν using asymptotic estimation, it utilized two sets of TSC data with 1K interval. This method enables one to get the exact value of ν and activation energy at the same time by using computer programming. So, it regards their calculation method as a useful process to obtain the value of physical behavior.

• Journal of the Korean Society of Safety
• /
• v.10 no.2
• /
• pp.3-9
• /
• 1995

Several piping material test methods have been developed as a result of advances in elastic-plastic fracture mechanics. It's known that, crack propagation of the materials strongly governed by the $J_{Ic}$ value. But the value is still difficult to be obtained because of it's complicate and troble-some determination process. In this paper, to prove the validity of the developed test procedure a series of tests were peformed at various temperatures and for different material directions. directions.