• Biotechnology and Bioprocess Engineering:BBE
• /
• v.11 no.5
• /
• pp.391-395
• /
• 2006

Microcapsules containing fragrant oils as a core material were prepared by in situ polymerization, using melamine-formaldehyde prepolymer as the wall material. The several parameters, such as stirring times, stirring rates, emulsifier types, emulsifier concentrations, and the viscosity of the core materials, affect the characteristics of the microcapsules. These parameters were investigated by the analyses of microcapsule size, particle size distribution, and morphology. The average microcapsule size decreased with an increase in stirring time, stirring rate, emulsifier concentration, and viscosity of the core material. It was also found that poly(vinyl alcohol) as a protective colloid could enhance the stability of the melamine-formaldehyde microcapsules.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.321-324
• /
• 1998

Pixel-Design Array Simulation Tool(PDAST) was used to profoundly the gate signal distortion and pixel changing capability, which are the most critical limiting factors for high-quality TFT-LCDs. Since PDAST can simulate the gate, data and pixel voltages of a certain pixel on TFT array at any time and at any location on an array, the effect of the resistivity of gate line material on the pixel operations can be effectively analyzed. The gate signal delay, pixel charging ratio, level-shift of the pixel voltage were simulated with varying the resis5tivity of the gate line material. The information obtained from this study could be utilized to design the larger area and finer image quality panel.

• Advances in nano research
• /
• v.7 no.5
• /
• pp.351-364
• /
• 2019

In this work, dynamic behavior of functionally graded (FG) porous nano-beams is studied based on nonlocal nth-order shear deformation theory which takes into the effect of shear deformation without considering shear correction factors. It has been observed that during the manufacture of "functionally graded materials" (FGMs), micro-voids and porosities can occur inside the material. Thus, in this work, the investigation of the dynamic analysis of FG beams taking into account the influence of these imperfections is established. Material characteristics of the FG beam are supposed to be vary continuously within thickness direction according to a "power-law scheme" which is modified to approximate material characteristics for considering the influence of porosities. A comparative study with the known results in the literature confirms the accuracy and efficiency of the current nonlocal nth-order shear deformation theory.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.1148-1154
• /
• 2009

This study focus on the suggestion of application manual using assembling reference plane design & standard finish material basis upon material classification code. We see it will function as a tool of a linkage between building design and construction standarization in order to enlarge the applicability of house building material that is produced by the module plan. For a estabilishing of this condition, it is neccessary to link the standardization's result of material--design--construction field. According to this neccessity, we are going to suggest information factor that can make relative business manager easily approach to the standardization practical task.

• Journal of Korea Water Resources Association
• /
• v.31 no.5
• /
• pp.539-552
• /
• 1998

When the pier is constructed in the cohesive be, the accuracy maynot be obtained because the equation for calculating the scour at piers is based upon the results which are analyzed through the experiments in the non-cohesive bed. In this paper, the variation of the depth of the pier scour occurred by constructing 5 types of pier in the channel having the cohesive material is examined. The experimental results are analyzed based upon Froude numbers and non-dimensional numbers which are indicated as the flow depths compared to the pier width. The results are also compared with the results obtained using the existing pier scour equations. In this paper, the shape factors, which can be used for calculating the scour depth of the pier in the cohesive channel bed, are suggested. The shape factors are indicated through the ratios between the scour depth at the circular pier and the scour depths at the different types of pier, and are suggested as two stages. In the first stage, in which the water depth compared to the pier width is less than 1.2, the shape factors are given as the equations. However, in the second stage the shape factors are given as the constant values. It is understood that the shape factors suggested in this paper can be properly usd for calculating local scour at piers in the bridges which are constructed in the cohesive channel bed having the characteristics of the bed material which is used in these experiments. Keywords : local scour, maximum scour depth, cohesive bed material, pier shape, pier, shape factor.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.4
• /
• pp.332-337
• /
• 2013

This paper presents a subsequent research work on the roller design of IRB(isolation roller bearing) seismic isolation device presented in Part 1 by focusing on heat treatment. The hardness and friction factor are very important factors of material and after-treatment process selection. Normally, roller bearing consists of roller and retainer. The roller gets high pressure constantly, while the retainer gets tensile and compressive stress. Therefore, sensitive material selection and heat treatment of each part is quite important. In this experimental evaluation, carbon steel, chrome special steel and others are employed and their characteristics after heat treatment are identified. Each material is prepared by refining high frequency heat treatment. The friction factor and static load capacity of manufactured material are experimentally identified and destructive test of material is processed. Optimal material and heat treatment conditions for IRB roller bearing are determined based on experiment results.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.5
• /
• pp.137-143
• /
• 2010

This research is a comparative analysis of the surface gloss of concrete depending on the coating material added to the cast, and includes analyses of the surface gloss of specimens made of cement mortar, with and without the addition of superplasticizer. In terms of coating material, the 7th material, which is part of a liquid packaging material, was shown to have the highest gloss, and was followed by the 3rd material, which uses transparent film. As the level of gloss is shown to vary depending on the material used for the coating film, it can be interpreted that the surface gloss can differ depending on surface particles and chemical composition factors. To make a concrete surface smooth, it is more effective to use a coating material with impermeability and a highly dense surface.

• Computers and Concrete
• /
• v.19 no.1
• /
• pp.87-98
• /
• 2017

In recent year, the coat layer drops and the rebar rust of bridge parapets, which caused the structural performance degradation. In order to achieve the comprehensive rehabilitation, ultra high performance cementitious composites is proposed to existing RC parapet rehabilitation. The influence factors of UHPCC rehabilitation includes two parts, i.e., internal factors related with material, such as UHPCC layer thickness, corrosion ratio of rebars, fiber volume fraction, and external factors related with the load, such as impact speeds, impact angles, vehicle mass. The influence of the factors was analyzed in this paper based on the nonlinear finite element. The analysis results of the maximum dynamic deformation and the peak impact load of parapets revealed the influence of the internal factors and the external factors on anti-collision performance and degree degradation. This research may provide a reference for the comprehensive multifunctional rehabilitation of existing bridge parapets.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.150-157
• /
• 1999

Developed in the study is the analysis of human factors involved in accidents of Korean Construction Projects. The 556 cases are sampled from a survey material 'Serious Accident Cases in the Construction Projects' edited by Korea Industrial Safety Corporation in 1995 through 1997. The analysis of these cases shows that existing classification system is not good for practical applications in real spots since they are difficult for engineers to understand. In this paper, human factors are classified into three groups by extracting the analysis and arrangement of the cases. Futhermore, We'll propose here a new type of accident which is subdivided. If engineers use this type of accident, they will be probably able to analyze efficiently human factors which are involved in accidents and relatied with how it happen. In the case of fall and upset accidents, personal factors seem to be critical when workers are horizontally moving in an unstable manner, and vertically moving without boarding facilities. Futhermore work environmental factors are important when workers release some materials and are performing building and dismantling tasks.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.31-34
• /
• 2000

It is very important to understand the correlation of between inter layer dielectric(ILD) CMP process and various facility factors supplied to equipment system. In this paper, the correlation between the various facility factors supplied to CMP equipment system and ILD CMP process were studied. To prevent the partial over-polishing(edge hot-spot) generated in the wafer edge area during polishing, we analyzed various facilities supplied at supply system. With facility shortage of D.I. water(DIW) pressure, we introduced an adding purified $N_2(PN_2)$ gas in polishing head cleaning station for increasing a cleaning effect. DIW pressure and PN2 gas factors were not related with removal rate, but edge hot-spot of patterned wafer had a serious relation. We estimated two factors (DIW pressure and PN2 gas) for the improvement of CMP process. Especially, we obtained a uniform planarity in patterned wafer and prohibited more than 90% wafer edge over-polishing. In this study, we acknowledged that facility factors supplied to equipment system played an important role in ILD-CMP process.