• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.37-40
• /
• 2002

Superconductor wire fabricated by electrophoresis showed its critical current density depended on parameters such as applied voltage and deposition time. Substrate and suspension solutions. and its properties are also important parameters. When same optimal parameter and condition was used, deposition density of superconductor film affect directly its critical current density. In this study, therefore, electrophoretic deposition technique was utilized for a densification of YBCO superconducting wire, and researches on electrophoretic suspension solutions and additive were experimentally performed for an improvement of the critical current density of fabricated electrophoretically superconducting wire. The samples fabricated in the solution with the additive, 8 vol.% of 1% PEG(1000), showed the highest critical current density.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.6
• /
• pp.962-971
• /
• 2004

This paper has dealt with thermo-physical properties of microencapsulated phase change material slurry as a latent heat storage material having a low melting point. The measured results of the thermo-physical properties of the test microencapsulated phase change material slurry, those are, density, specific heat, thermal conductivity and viscosity, were discussed for the temperature region of solid and liquid phases of the dispersion material (paraffin). The measurements of these properties of microencapsulated phase change material slurry have been carried out by using a specific-gravity meter, a water calorimeter, a differential scanning calorimeter(DSC), a transient hot wire method and rotating type viscometer, respectively. It was clarified that the additional properties law could be applied to the estimation of the density and specific heat of microencapsulated phase change material slurry and also the Euckens equation could be applied to the estimation of the thermal conductivity of this slurry.

• Journal of Surface Science and Engineering
• /
• v.48 no.4
• /
• pp.131-135
• /
• 2015

We investigated the surface morphology and the change of Ag concentration for SnAg electrodeposits according to the current density using labmade and commercial plating solutions. The concentration of Ag in the SnAg electrodeposits decreased with increasing the current density. The Ag concentrations at the conditions of over $50mA/cm^2$ were below 3 wt% and the surface was relatively smooth. Cu pillar bump was fabricated by using SnAg electroplating, and it was reflowed at $240^{\circ}C$ for 90 sec. The cross-sectional microstructure was investigated by using EBSD measurement and it was found that the grain size of SnAg became smaller by increasing the number of reflow treatments.

• Korean Journal of Materials Research
• /
• v.18 no.8
• /
• pp.406-410
• /
• 2008

The properties of pyrolytic carbon (PyC) deposited from $C_2H_2$ and a mixture of $C_2H_2/C_3H_6$ on $ZrO_2$ particles in a fluidized bed reactor were studied by adjusting the deposition temperature, reactant concentration, and the total gas flow rate. The effect of the deposition parameters on the properties of PyC was investigated by analyzing the microstructure and density change. The density could be varied from $1.0\;g/cm^3$ to $2.2\;g/cm^3$ by controlling the deposition parameters. The density decreased and the deposition rate increased as the deposition temperature and reactant concentration increased. The PyC density was largely dependent on the deposition rate irrespective of the type of the reactant gas used.

• Geomechanics and Engineering
• /
• v.13 no.4
• /
• pp.601-619
• /
• 2017

Cantilever retaining wall movements generally depend on the intensity and duration of ground motion, the response of the soil underlying the wall, the response of the backfill, the structural rigidity, and soil-structure interaction (SSI). This paper investigates the effect of material properties on seismic response of backfill-cantilever retaining wall-soil/foundation interaction system considering SSI. The material properties varied include the modulus of elasticity, Poisson's ratio, and mass density of the wall material. A series of nonlinear time history analyses with variation of material properties of the cantilever retaining wall are carried out by using the suggested finite element model (FEM). The backfill and foundation soil are modelled as an elastoplastic medium obeying the Drucker-Prager yield criterion, and the backfill-wall interface behavior is taken into consideration by using interface elements between the wall and soil to allow for de-bonding. The viscous boundary model is used in three dimensions to consider radiational effect of the seismic waves through the soil medium. In the seismic analyses, North-South component of the ground motion recorded during August 17, 1999 Kocaeli Earthquake in Yarimca station is used. Dynamic equations of motions are solved by using Newmark's direct step-by-step integration method. The response quantities incorporate the lateral displacements of the wall relative to the moving base and the stresses in the wall in all directions. The results show that while the modulus of elasticity has a considerable effect on seismic behavior of cantilever retaining wall, the Poisson's ratio and mass density of the wall material have negligible effects on seismic response.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.183-188
• /
• 1996

The compressive stress-strain response of Low Density Polyurethane foam material is modeled using the finite element method. A constitutive equation which include experimental constants based on quasi-static and dynamic uniaxial compression test is proposed. Impact test with different impactor masses and velocities are performed to verify the proposed model. The comparison between impact test and finite element analysis shows good agreements.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.365-368
• /
• 2000

We have studies on the Microstructures and densities as a function of forming pressures and the magnetic properties of the specimens with additive Bi$_2$O$_3$ that sintered at 95$0^{\circ}C$ for 4.5 hours for synthesizing optimal Ni-Cu-Zn ferrite. Green density rose generally as Forming pressure increased from 1.7 ton/cm$^2$to 2.5 ton/cm$^2$and Cold Isostatic Pressure(CIP) method was more effective than Die Pressure(DP) method to high green density. Forming pressure had no influence on apparent density but on the other hand Bi$_2$O$_3$contents were strongly dominant to appaernt density than forming pressure. Bi$_2$O$_3$liquid phases created during sintering process promoted sintering and grain growth so that apparent density, grain size and permeability increased compared to that of the specimens which were sintered with non-additive Bi$_2$O$_3$.

• Korean Journal of Materials Research
• /
• v.33 no.7
• /
• pp.273-278
• /
• 2023

In this study, based on the saturation magnetic flux density experimental values (B_s) of 622 Fe-based bulk metallic glasses (BMGs), regression models were applied to predict B_s using artificial neural networks (ANN), and prediction performance was evaluated. Model performance evaluation was investigated by using the F1 score together with the coefficient of determination (R² score), which is mainly used in regression models. The coefficient of determination can be used as a performance indicator, since it shows the predicted results of the saturation magnetic flux density of full material datasets in a balanced way. However, the BMG alloy contains iron and requires a high saturation magnetic flux density to have excellent applicability as a soft magnetic material, and in this study F1 score was used as a performance indicator to better predict B_s above the threshold value of B_s (1.4 T). After obtaining two ANN models optimized for the R² and F1 score conditions, respectively, their prediction performance was compared for the test data. As a case study to evaluate the prediction performance, new Fe-based BMG datasets that were not included in the training and test datasets were predicted using the two ANN models. The results showed that the model with an excellent F1 score achieved a more accurate prediction for a material with a high saturation magnetic flux density.

• Clean Technology
• /
• v.29 no.4
• /
• pp.249-254
• /
• 2023

In this study, porosity estimation was conducted by the physical properties of zeolite. Because of the difficulty of directly measuring the porosity of particulate matter, the porosity was calculated by applying the measured physical properties of zeolite to the calculation formula presented in various literature. For this purpose, the average particle size, particle size distribution, specific surface area, and pore characteristics of three types of zeolite - zeolite beta, zeolite Y, and ZSM-5 - were measured. In addition, the true density using gas and liquid phases, and two types apparent density (tap and untapped density) were measured. We calculated the porosity using these results, compare and analyzed the results, and evaluated main factors that determine the porosity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.229-232
• /
• 1997

A free space transmission method using standard gain horn antennas in the frequency range from 9.0 to 10.5GHz is applied to determine the dielectric properties of grain such as rough rice, brown rife and barley. The dielectric constant and loss factor, which depend on the moisture content of the wetted grain are obtained from the measured attenuation and phase shift by vector network analyzer. The effect of density fluctuation, which is an important parameter governing the dielectric properties of grain, on the dielectric constant and loss factor is presented. A new density-independent model in terms of measured attenuation and moisture density is proposed for reducing the effects of density fluctuation on the moisture content measurement.