• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.72-77
• /
• 1998

A defect model for UO$_2$ fuel containing soluble fission products was devised based on the defect structure of pure and doped uranias. Using the equilibrium between fuel solid-solution and fission-products and the material balance within the fuel, a tracing method to get the stoichiometry change of urania fuel with burnup was made. This tracing method was applied to high burnup urania fuel and DUPIC fuel. The oxygen potential of urania fuel turned out to increase slightly with burnup. The stoichiometry change was calculated to be negligible due to the buffering role f Mo. The oxygen potential of DUPIC fuel out to be sensitive to the initial chemical state of Mo in the fuel.

• The Korean Journal of Ceramics
• /
• v.5 no.1
• /
• pp.78-81
• /
• 1999

Aluminium titanate is highly anisotropic in thermal expansion. As a result, thermal stresses build up in the material and intergranular cracks can develop. Both the outstanding thermal shock resistance and the low mechanical strength of aluminium titanate ceramics are a result of intergranular microcracking. The authors have previously identified a possibility of remarkably increasing fracture toughness of aluminium titanate without excessive penalty on strength. The paper shows that sintered density and porosity measurements can be used for optimizing the sintering and microstructure of aluminium titanate for an ideal balance between toughness and strength and, hence, the best thermal shock resistance.

• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.62-69
• /
• 1993

Friction and wear behavior of a carbon/carbon composite material for aircraft brake material was experimentally investigated. Friction and wear test setup was designed and built for the experiment. Friction and wear tests were conducted under various sliding conditions. Friction coefficients were measured and processed by a data acquisition system and amount of wear measured by a balance. Stainless steel disk was used as the counterface material. Temperature was also measured by inserting thermocouple 2.5 mm beneath the sliding surface of the carbon/carbon composite specimen. Wear surfaces were observed by SEM, and analyzed by EDAX. The experimental results showed that sliding speed and normal force did not have significant effects on friction coefficient and wear factor of the composite. Temperature increase just below the surface was not large enough to cause any thermal degradation or oxidation which occurred at higher temperature when tested by TGA. Wear film was generated both on the specimen and on the counterface at relatively low sliding speed but cracks, grooves, and wear debris were observed at high sliding speed. Friction coefficient remained almost constant when the sliding speed or normal load was varied. It is believed that the adhesive and abrasive components contributed mainly to the friction coefficient. Wear behavior at low sliding speed was governed by wear film formation and adhesive wear mechanism. At high speed, fiber orientation, ploughing by counterface asperities, and fiber breakage dominated wear of the carbon/carbon composite.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1312-1315
• /
• 2004

Chemical Mechanical Polishing is referred to as a three body tribological system, because it includes two solids in relative motion and the slurry. On the assumption that the abrasives between the pad and the wafer could be a major reason of not only the friction force but also material removal during polishing. The friction force generated by the abrasives was inspected with the change of abrasive size and concentration in this paper. The variation of coefficient of friction with abrasive concentration and size could result from the condition of contact and load balance between wafer and abrasives carried by pad asperity. The simulation was performed in this paper and compared with the result of experiment. The material removal rate also estimated with abrasive concentration and size increasement.

• Journal of Magnetics
• /
• v.3 no.4
• /
• pp.99-104
• /
• 1998

The $ Sm_2Fe_{17}N_x $materials were prepared by the combination consisting of the HDDR (hydrogenation, disproportionation, desorption, and recombination) process and nitrogenation or by the conventional way consisting of nitrogenation only, and the magnetic and thermomagnetic properties of the materials were investigated. The magnetic characterisation of the prepared $ Sm_2Fe_{17}N_x $ materials was performed using a VSM. Thermal stability of the materials was evaluated using a DTA under Ar gas atmosphere. The thermomagnetic characteristics of the materials were examined using a Sucksmith-type balance. The previously HDDR-treated Sm2Fe17parent alloy was found to be nitrogenated more easily compared to the ordinary $ Sm_2Fe_{17}N_x $alloy. The $ Sm_2Fe_{17}N_x $ material produced by the combination method showed a high coercivity (12.9 kOe) even in the state of coarse particle size (around 60 ${\mu}{\textrm}{m}$). It was also revealed that the $ Sm_2Fe_{17}N_x $ material produced by the material produced by the combination showed an unusual TMA tracing featured with a low and constant magnetisation at lower temperature range and a peak just before the Curie temperature. This thermomagnetic characteristic was interpreted in terms of the competition between two counteracting effects; the decrease in magnetisation due to the thermal agitation at an elevated temperature and the increase in magnetisation resulting from the rotation of magnetisation of the fine grains comparable to a critical single domain size due to the decreased magnetocrystalline anisotropy at an elevated temperature.

• Journal of Ginseng Research
• /
• v.43 no.4
• /
• pp.618-624
• /
• 2019

Background: Ginsenoside Re (Re) is one of the major components of Panax ginseng Meyer. Ginsenoside $Rk_3$ ($Rk_3$) is a secondary metabolite of Re. The aim of this study was to investigate and compare the effects and underlying mechanisms of Re and $Rk_3$ on cyclophosphamide-induced myelosuppression. Methods: The mice myelosuppression model was established by intraperitoneal (i.p.) injection of cyclophosphamide. Peripheral blood cells, bone marrow nucleated cells, and colony yield of hematopoietic progenitor cells in vitro were counted. The levels of erythropoietin, thrombopoietin, and granulocyte macrophage colony-stimulating factor in plasma were measured by enzyme-linked immunosorbent assay. Bone marrow cell cycle was performed by flow cytometry. The expression of apoptotic protein bcl-2, bax, and caspase-3 was detected by Western blotting. Results: Both Re and $Rk_3$ could improve peripheral blood cells, bone marrow nucleated cell counts, thymus index, and spleen index. Furthermore, they could enhance the yield of colonies cultured in vitro and make the levels of granulocyte macrophage colony-stimulating factor, erythropoietin, and thrombopoietin normal, reduce the ratio of $G_0/G_1$ phase cells, and increase the proliferation index. Finally, Re and $Rk_3$ could upregulate the expression of bcl-2, whereas they could downregulate the expression of bax and caspase-3. Conclusion: Re and $Rk_3$ could improve the hematopoietic function of myelosuppressed mice. The effect of $Rk_3$ was superior to that of Re at any dose. Regulating the levels of cytokines, promoting cells enter the normal cell cycle, regulating the balance of bcl-2/bax, and inhibiting the expression of caspase-3 may be the effects of Re and $Rk_3$ on myelosuppression.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.2
• /
• pp.126-132
• /
• 2012

In recent years, serious environmental problems occur in coastal area due to high pollution loads from human activity in land. Marine biomass utilization system therefore has been proposed to prompt material circulation between land and sea. Comprehensive assessment is necessary to determine that the proposed system is suitable and sustainable. This study introduces thermodynamic concept exergy, which expresses energy quality, to describe material and energy flowing in the material circulation system. This study presents material, energy and exergy flows in the material circulation system at Sakai city located in the middle of Osaka in Japan. It is found that exergy helps a better understanding of what is a key role is in exergy-efficient material circulation system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.140-140
• /
• 2009

The polymer electrolyte membrane fuel cell(PEMFC) with the advantages of low-operating temperature, high current density, low cost and volume, fast start-up ability, and suitability for discontinuous operation becomes the most reasonable and attractive power system for transportation vehicle and micro-grid power plant in a household. 200W PEM-type FCs system was integrated by this study, then the electrical characteristics and diagnosis of the fuel cell were analyzed with variations on mass flow rate and stack temperature. The ranges of the variations are $20{\sim}70^{\circ}C$ on stack temperature and 1~8L/min on $H_2$ volume.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.47-50
• /
• 2002

The displacemant current measuring system used for detecting the dynamic behavior of monolayers at the air-water interface is described. It basically consists of a film balance, a pair of electrodes connected to each other through a sensitive ammeter. Here, one electrode is suspended in air and the other electrode is placed in the water. With Maxwell-displacement-current-measuring method, the phase transitons of $Poly-{\gamma}-benzyl_{L}$ -glutamate (PBLG) and $Poly-{\gamma}-benzyl_{D}$-glutamate(PBDG) on a water surface were detected. Measured surface pressure, displacement current and dipole moment of monolayers of PBLG and PBDG on the water surface. Also, we measured that compression velocity (30, 40, 50[mm/min]) when the sample spread volume was about 370[ul]-400[ul] and displacement current that occur when differed temperature. From the result, it is known that current is generated in the range of high surface pressures as compression velocity become faster and increase of temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.137-140
• /
• 2002

EM(ElectroMagnetic) pump is used for the purpose of transporting liquid sodium coolant with electrical conductivity in the LMR(Liquid Metal Reactor). In the present study, computer program for the pilot annular linear EM pump has been developed for the maximum flowrate with 200 l/min and maximum developing pressure with 3 bar. Firstly, Balance equation is induced by the equivalent circuit method which is commonly employed to analyze linear induction machines and the calculation of the hydraulic pressure drop. Then, design equation is converted to the computer program and optimum pump variables are determined by this code. The code is verified by the comparative analysis with the characteristic of the commercialized pump.