• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.685-692
• /
• 1998

Since a wet-seal area of Molten Carbonate Fuel Cell (MCFC) operated at $650^{\circ}C$ is exposed to severe environment, a life-time of MCFC is influenced by the corrosion resistance of separator. In order to improve corrosion resistance of 316L stainless steel used as separator material, AI- base alloy such as NiAI has been widely used as coat¬ing material on the wet-seal area. The purpose of this work is to develope a more protective coating material by adding yttrium on NiAI alloy. An immersion test and a polarization test were performed in molten carbonate salt at $650^{\circ}C$ to estimate corrosion resistance of the NiAI alloy and the NiAl/Y alloys with up to L5at% yttrium. NiAl/Y alloys showed better corrosion resistance than NiAI alloy. We found that more than 0.7 at% yttrium was required to improve the corrosion resistance of NiAI alloy in molten carbonate salt at $650^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.701-709
• /
• 2011

In semiconductor wafer fabrication, etching is one of the most critical processes, by which a material layer is selectively removed. Because of difficulty to correct a mistake caused by over etching, it is critical that etch should be performed correctly. This paper proposes a new approach for etch endpoint detection of small open area wafers. The traditional endpoint detection technique uses a few manually selected wavelengths, which are adequate for large open areas. As the integrated circuit devices continue to shrink in geometry and increase in device density, detecting the endpoint for small open areas presents a serious challenge to process engineers. In this work, a high-resolution optical emission spectroscopy (OES) sensor is used to provide the necessary sensitivity for detecting subtle endpoint signal. Partial Least Squares (PLS) method is used to analyze the OES data which reduces dimension of the data and increases gap between classes. Support Vector Machine (SVM) is employed to detect endpoint using the data after PLS. SVM classifies normal etching state and after endpoint state. Two data sets from OES are used in training PLS and SVM. The other data sets are used to test the performance of the model. The results show that the trained PLS and SVM hybrid algorithm model detects endpoint accurately.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.525-526
• /
• 2007

Over-polishing is required to completely remove the material of top surface across whole wafer, in spite of a local dishing problem. This paper introduces the two-step CMP process using protective layer and high selectivity slurry, to reduce dishing amount and variation. The 30nm thick protective oxide layer was deposited on the pattern, and then polished with low selectivity slurry to partially remove the projected area while suppressing the removal rate of the recessed area. After the first step CMP process, high selectivity slurry was used to minimize the dishing amount and variation in pattern structure. Experimental result shows that two-step CMP process can be successfully applicable to reduce the dishing defect generated in over-polishing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.589-592
• /
• 2005

Micro-forming is a suited technology to manufacture very small metallic parts(several $mm{\sim}{\mu}m$). Micro-forming of $Zr_{62}Cu_{17}Ni_{13}Al_8$ bulk metallic glass(BMG) as a candidate material for this developing process are feasible at a relatively low stress in the supercooled liquid state without any crystallization during hot deformation. In this study, micro-formability of a representative bulk metallic glass, $Zr_{62}Cu_{17}Ni_{13}Al_8$, was investigated for micro-forging of U-shape pattern. Micro-formability was estimated by comparing $R_f$ values $(=A_f/A_g)$, where Ag is cross-sectional area of U groove, and $A_f$ the filled area by material. Microforging process was simulated and analyzed by applying finite element method. FEM simulation results should reasonable agreement with the experimental results when the material properties and simulation conditions such as top die speed, remeshing criteria and boundary conditions tightly controlled. The micro-formability of $Zr_{62}Cu_{17}Ni_{13}Al_8$ was increased with increasing load and time in the temperature range of the supercooled liquid state. Also, FEM Simulation using DEFORM was confirmed to be applicable for the micro-forming process simulation.

• Nano
• /
• v.13 no.10
• /
• pp.1850113.1-1850113.11
• /
• 2018

Environmental and energy issues have always been a hot topic of global research. Oil leakage has caused great damage to the environment, affecting a wide area and it is difficult to clean up. In most cases, carbon-based adsorbents are typically utilized to remove oil spills because of their economic benefits and high adsorbent efficiency. At the same time, its excellent material properties can also be used for the preparation of supercapacitors. In this paper, the carbon aerogels were prepared by the one-step method. The prepared materials endowed a 3D network structure with a huge number of micropores and mesoporous, and the material is light-weight, stable, hydrophobic and has affinity for oil (17.02 g/g) to the KGM carbon aerogel. Through the physicchemical characterization, the KGM carbon aerogel shows specific surface area is $689m^2/g$, high water contact angle ($136.64^{\circ}$) and excellent reusability (more than 15 cycle times). In addition, we also discussed the electrochemical properties of the material and obtained the specific electrical capacity of 139 F/g under the condition of 1 A/g.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.672-682
• /
• 2008

The resistance spot welding of TRIP590 steels was investigated to enhance understanding of weld fracture during tensile-shear strength (TSS) test. The main failure modes for spot welds of TRIP590 steels were nugget pullout and interfacial fracture. The peak load to cause a weld interfacial failure was found to be related to fracture toughness of the weld and the weld diameter. Although interfacial fracture occurred in the samples, the load carrying capacity of the weld was high and not significantly affected by the fracture mode. Substantial part of the weld exhibits the characteristic dimple (or elongated dimple) fractures on interfacial fractured surface, in spite of the high hardness values associated with the martensite microstructures. The high load-bearing ability of the weld is directly associated with the area of ductile fracture occurred in weld. Therefore, the judgment of the quality of resistance spot welds in TRIP590 steels, the load carrying capacity of the weld should be considered as an important factor than fracture mode.

• Journal of the Korean Electrochemical Society
• /
• v.24 no.3
• /
• pp.42-51
• /
• 2021

Dissociation into Lithium-polysulfide electrolyte due to repeated cycles during the Lithium/Sulfur battery reaction is a major problem of reduced battery lifespan. We searched for a porous carbon with a large specific surface area that infiltrated S to prevent liquid Lithium-polysulfide from being dissolved in electrolyte, induce adsorption of Lithium-polysulfide, and further increase conductivity. In order to obtain porous carbon spheres with a large specific surface area, the carbon spheres of 1939 m²/g were raised to 2200 m²/g through additional KOH treatment. In addition, through heat treatment with S, a carbon sulfur compound containing 75 wt% of S was fabricate and material analysis was conducted on the possibility of using the cathode material. The electrochemical characteristics of the Reference (622; sulfur: 60%, conductive material: 20%, binder: 20%) pouch cell and the pouch cell made using 75wt% of carbon sulfur compound were analyzed. 75wt% of carbon sulfur pouch cell showed a 20% increase in lifespan and 10% improvement in C-rate compared to the Reference pouch cell after 50 cycles.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.1
• /
• pp.63-73
• /
• 2010

The supply of high quality filling materials for pavement base course or reclamation is getting harder. So, there is an attempt to use soft mudstones as an earth filling material in Pohang area. But the engineering properties of the soil deposit placed with soft mudstones have not been clearly evaluated yet. We investigated the water absorption and softening, the slaking behavior and the geological mechanism in order to obtain an effective way of estimating the magnitude of land subsidence and the reduction of soil strength. The applicability of soft mudstones is examined by a variety of laboratory tests and pilot-scale field tests. In addition, it is necessary to consider the environmental characteristics of soft mudstones as a reclaiming material, Consequently, the results from the current study can be used to prevent any construction defects due to the careless use of soft mudstones for the pavement base course or reclamation.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2008.04a
• /
• pp.203-208
• /
• 2008

The purpose of the study is to establish the concept of residential standard, and at the same time to investigate the area of the minimum residential standard in the countries of the world through the preceding studies. In addition, it also aims at establishing the objective residential standard by comparing the residential standard of Korea with that of foreign countries, examining the problems and finding out the matters to be improved through the comparison of the residential standard in advanced countries with the minimum residential standard of Korea. The standard residential area, derived from the process of examining the minimum residential standard, will be used as the basic material for the calculation of the reasonable area in the surface plan for the study of low-cost housing development. The method of the study is to establish the concept of residential standard and at the same time to find out the problems in the minimum residential standard of Korea and improvement methods through the comparison of the residential standards in other countries. As the result of the studies focused on the area among the residential standards, it is found out that the Korea's residential area per capita is established as the least in comparison with that of advanced countries. The real area decided depending on the size of social space suitable for living can play a role in improving the degree of satisfaction in the person's living in the residential area. Therefore, it is urgently necessary to make a depth study on the surface area of the minimum residential standard, and it is also required to propose the residential standard and directions for the improvement of the qualitative level rather the quantitative expansion of residential structures.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.314-314
• /
• 2022

In the production of rice flour, wet milling is a method of milling rice after soaking it in water, and it takes a lot of time and cost from milling to drying. To overcome this problem, the floury type rice was developed for dry milling and it is known to have round starch granules, low content of damaged starch after milling, and a starch structure similar to wheat. Because of its unique properties different from normal rice, it is necessary to research on processing and characteristics of floury-type rice to expand its utility in the food industry. Therefore, this study aimed to prepare the pregelatinized floury type rice (Baromi2) by autoclave and investigate their physicochemical properties. As the heat treatment time increased, the brightness decreased from 83.8 to 76.8, however, both redness and yellowness increased from 0.57 to 4.5 and from 14.58 to 21.13, respectively. Despite of same treatment time, soaking in water (10 min) before autoclaving increased the solubility and swelling power of Baromi2 over 2 times. The peak viscosity of native Baromi2 was over 2000 RVU, on the other hand, there was a significantly decrease to less than 1000 RVU of pregelatinized Baromi2. Heat treatment without immersion caused partial gelatinization of starch, resulting that some starch granules maintaining their integrity. Whereas there were no starch granules in heat treatment with soaking in water due to complete gelatinization. This study would be helpful to the suggestion of using heat-treated floury-type rice as an intermediate material in the food industry in the future.