• 소성∙가공
• /
• 제17권1호
• /
• pp.9-12
• /
• 2008

Recently, industries and academic institutes have been interested in the rheology forming technology for light weight materials. However, this rheocasting process has advantages such as the high initial investment cost and the lower mechanical properties than thixocasting. In this study, the continuous fabrication of rheological material with a spiral stirring equipment(mechanical stirring system) was newly devised to overcome the disadvantages of rheocasting process. The experimental parameters were stirring time($0{\sim}1200sec$), stirring velocity ($0{\sim}100rpm$) and stirring temperature($650{\sim}680^{\circ}C$). The optimal conditions for fabricated rheological material of A6061 alloy were stirring time at 300sec, stirring velocity at 60rpm and stirring temperature at $650^{\circ}C$. At these results, the equivalent diameter was $45{\sim}65{\mu}m$, mean roundness was $1.4{\sim}1.6$ and Vickers hardness was 60Hv.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.453-456
• /
• 2004

This paper surveys the latest findings on vegetable-oil-based dielectric coolants in power systems. In recent years, environmental concerns have been increased on the use of poorly biodegradable mineral oils in distribution and power transformers in regions where spills from leaks and equipment failure could contaminate the surroundings. In addition, there are demands to improve equipment efficiencies in power systems. In this reason, researches were started in the mid 1990s to develop a fully biodegradable dielectric coolants. Vegetable oil was considered the most likely candidate for a fully biodegradable dielectric coolants. Vegetable-oil-based dielectric coolants provide the advantages of high level of biodegradability, renewable natural resource, non-toxic properties, enhanced fire safety, more effective cooling and good dielectric strength for many electrical equipment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.230-233
• /
• 1999

Because Insulation material is play an important part for normal work of electricity equipment, the study is advanced, but as the voltage of electricity system is raising, we required that new lnsulation material. They have excellent specific against high stress, namely the study of insulation increase and prevention diagnosis of insulation degradation of Epoxy or XLPE and so on. In this thesis. I utilize image processing technique for effective inspection of insulation material degradation.

• 문화기술의 융합
• /
• 제6권1호
• /
• pp.477-483
• /
• 2020

콘크리트 박스 구조물이 열화되어 보수보강이 필요할 경우 스프레이 장비로 구조물 단면에 보수재를 분사하여 부착시키는 방법에 의존하고 있는데 천장 또는 벽체부위의 경우 시공 후 보수재 자중 또는 중력에 의해 부착력이 저하될 수 있으며 지하철 구조물의 경우 진동 등에 의해 초기 부착력이 떨어지는 문제점이 발생한다. 또한 작업자의 숙련도와 시공환경에 따라 보수품질이 변동되기에 이에 대한 보완책이 필요한 실정이다. 본 연구에서는 중력에 의한 보수재의 부착력 저하 및 인력시공에 의한 보수품질의 변동과 같은 문제점을 해결하고자 보수재 시공 후 소정의 압력을 가할 수 있는 기계식 가압장비를 개발하였다. 그리고 가압장비의 성능을 알아보고자 현장조건을 모사할 수 있는 챔버를 제작하여 가압 유무, 단면부위 및 환경조건을 달리한 부착강도를 측정한 결과 가압할 경우 그렇지 않은 경우보다 부위별로 차이가 있었으나 최대 70% 부착강도가 증가하는 효과를 얻을 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.398-402
• /
• 2005

Structureborne noise induced by shipboard equipment is one of the most significant noise source of ships and can be effectively reduced by resiliently mounting them. In this paper, the pole parameter method is investigated for estimating the structureborne noise reduction of resiliently mounted equipment. In addition, we suggest how to evaluate pole parameters from dimensional and material information of each component consisting of resiliently mounted equipment. To validate and discuss the proposed method numerical analysis for single and double resiliently mounted equipment systems using both pole parameter method and FEM have been done.

• 한국산업융합학회 논문집
• /
• 제22권6호
• /
• pp.785-795
• /
• 2019

This paper is a study on the modeling of the quantity estimation model for offshore plant Material handling equipment in FEED(Front End Engineering Design) verification stage using system engineering approach which is an engineering design methods. The relevant engineering execution procedure is not systemized although the operation method and Material handling equipment selection with weight and space constraints is a key part of the FEED. Using the system engineering process, the stakeholder requirements analysis process, the system requirements analysis, and the final system architecture design were sequentially performed, and the process developed through the functional development diagram and Requirement traceability matrix (RTM) was verified. In addition, based on the established process, we propose a Material handling quantity estimation model and Quantity calculation verification Table that can be applied at the FEED verification stage and we verify the applicability through case studies.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1415-1424
• /
• 2009

Measuring dynamic properties of gravel-sized materials demands large specimens. Due to the difficulties in experiment as well as equipment, the dynamic properties of gravel-sized material has rarely been investigated. To realize free-free end condition more properly and stabilize specimen during testing with new specimen support system, a free-free resonant column testing device, which is capable of testing gravel-sized materials and constraining a specimen in free-free boundaries, is developed. We report the calibration of the equipment and preliminary testing results on Jumunjin sand. The testing data are compared with the previous data obtained from the existing fixed-free resonant column test.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.107-110
• /
• 1999

The purpose of this research is for the development of a new type forging equipment H.C.G(Hyundai Continuous Grain-flow) by using two virtual build-up tools rigid viscoplastic FEM and downsized plasticine experiment. This forging equipment consists of consecutive horizontal and vertical pressure while the traditional forging method consists of only vertical pressure. Using this method high quality crankshafts can be forged as it can maintain a continuous grain flow. The factors considered in the development of equipment are die geometry for flawless deformed shape die reaction forces stress/strain distributions and continuous material flow. We carried out several numerical simulations and downsized plasticine experiments for the proper design of the forging equipment. The validity of those simulation results is confirmed by checking with the actual test results. Based on these simulation results the proper design of the H.C.G for ging equipment is enabled.

• 융합경영연구
• /
• 제10권3호
• /
• pp.1-8
• /
• 2022

Purpose: This study aims to examine the effect of SMEs' R&D competence on management performance. Research design, data, and methodology: The empirical data of this study are derived from 2,375 SMEs that participated in the material, parts, and equipment research and development support project conducted from 2014 to 2018. Among them, 2,230 data were analyzed by classifying them into high-tech and low-tech fields. SPSS 24.0 was used for statistical analysis and correlation analysis and T-TEST were applied. Results: It was analyzed that the level of R&D organization, research personnel, and the number of patent registrations all affected operating profit and sales. In particular, it has been proven that research personnel have a greater impact on management performance among the level of R&D organization, research personnel, and the number of patent registrations. In addition, there was a difference between high-tech and low-tech industries in the impact on operating profit and sales, which are indicators of management performance. Conclusions: This study suggests that R&D competence are strengthened to advance the material, parts, and equipment industries and to promote future growth, while differentiated support is needed according to each company's R&D competence and technology level.

• Structural Engineering and Mechanics
• /
• 제33권2호
• /
• pp.257-260
• /
• 2009