• Particle and aerosol research
• /
• v.5 no.4
• /
• pp.179-188
• /
• 2009

The dry deposition fluxes of particulate polychlorinated biphenyls (PCBs) were measured along with their mass size distributions at Seoul and Incheon in fall in 1999. The dry deposition fluxes of PCBs were in the range of $16.7{\sim}62.2ng/m^2/day$. The ambient concentrations of particulate PCBs were in the range of 0.07 to $0.20ng/m^3$. Generally, the mass size distribution of particulate PCBs shows bi-modal distribution. The mass fraction of PCBs in the fine particle fraction ($D_p<2.1 {\mu}m$) was over than 55% of the total PCBs concentrations. It was found that Seoul and Incheon were not the major source of PCBs emissions in Korea. Based on the comparison with the measurement data in summer, 1999, it is likely that both the dry deposition fluxes and ambient particulate PCBs concentrations were not site-specific.

• Korean Journal of Hazardous Materials
• /
• v.6 no.2
• /
• pp.95-104
• /
• 2018

Gas-liquid bubble column reactors are extensively used in industrial processes. A detailed knowledge of bubble size distribution is needed for determining the mass transfer in gas-liquid film. Experimental data on bubble size distribution and liquid-side mass transfer coefficient($k_L$) were used to calculate the estimated time to saturation in bubble column reactor. Also, the gas flux was evaluated to the liquid-side mass transfer coefficient($k_L$) and solubility data for hydrogen sulfide($H_2S$) and chlorine($Cl_2$) absorption into water. Simulation results show that $H_2S$ absorption time to 50 % of saturation concentrations are 611 sec and 1,329 sec when bubble diameters are 0.5 mm and 4.5 mm, while absorbing 1 % $H_2S$ gas. In case of $Cl_2$, absorption time range 657 to 1,400 sec when bubble size range 0.5 mm to 4.5 mm, while absorbing 1 % $Cl_2$ gas. Calculated simulation results can be used in the design of emergency relief bubble reactors.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.197-203
• /
• 2014

The liquid jet breakup has been studied in the areas such as aerosols, spray and combustion. The breakup depends on several physical parameters such as the jet velocity, the nozzle inner diameter, and the density ratio of the water to the jet. This paper deals with characteristics of the jet breakup according to the jet velocity and the nozzle diameter. In order to consider only hydrodynamic factors, all the experiments were conducted in non-boiling conditions. The jet behavior in the water pool was observed by high-speed camera and PIV technique. For the condition of the inner diameter of 6.95 mm and the jet velocity of 2.8 m/s, the debris size of 22 mm gave the largest mass fraction, 39%. For higher jet velocity of 3.1 m/s, the debris size of 14 mm gave the largest mass fraction, 36%. For the nozzle with inner diameter of 9.30 mm, the debris size distribution was different. For jet velocity of 2.8 m/s and 3.1 m/s, the debris size with the largest mass fraction was found to be 14 mm. It was identified that the debris size decreased as the diameter or the jet velocity increased.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.25 no.4
• /
• pp.472-481
• /
• 2015

Objectives: Welding is a major task in shipbuilding yards that generates welding fumes. A significant amount of welding in shipbuilding yards is done on steel. Inevitably, manganese is present in the base metals being joined and the filler wire being used and, consequently, in the fumes to which workers are exposed. The objective of this work was to characterize manganese exposure associated with work area, total and particle size-selective mass concentration, and compare the mass concentrations obtained using a three-piece cassette sampler, size-selective impactor sampler and blood manganese concentrations. Materials: All samples were collected from the main work areas at one shipbuilding yard. We used a three piece cassette sampler and the eight stage cascade impactor sampler for the airborne manganese mass concentration of total and all size fractions, respectively. In addition, we used the results of health examination of workers sampled for airborne manganese. Results: The oder of high concentration of airborne manganese in shipbuilding processes was as follows; block assembly, block erection, outfitting installation, steel cutting, and outfitting preparation. The percentages of samples that exceeded the OES of the ministry of employment and labor by the cassette sampling method was 12.5%, however 59.1% of sampled workers by the impactor sampling method exceeded the TLV of the ACGIH. Conclusions: Even though the manganese concentrations in blood of workers exposed to higher airborne manganese concentration were higher than among those exposed to lower concentrations, there was no difference in blood manganese concentrations among work duration. The data analyzed here by characterizing size-selective mass concentrations indicates that the inhaled manganese of welders in shipbuilding yards could be mostly manganese-containing respirable particle sizes.

• Journal of the Korean earth science society
• /
• v.41 no.1
• /
• pp.1-18
• /
• 2020

This study presented the effects of the assumed mass-size relationship for snow on the simulated surface precipitation by using cloud microphysics parameterizations in Weather Research and Forecasting (WRF) model. The selected cloud microphysics parameterizations are WRF Double-Moment 6-class (WDM6) and WRF Single-Moment 6-class (WSM6) in the WRF model. We replaced the mass-size relationship for snow in WDM6 and WSM6 with Thompson's mass-size relationship retrieved from measurement data. The sensitivity of the modified WDM6 and WSM6 was tested for the idealized 2-dimensional squall line and winter precipitation system over the Korean peninsula, respectively. The modified WDM6 and WSM6 resulted in the increase of graupel/rain mixing ratios and the decrease of snow mixing ratio in the low atmosphere. The changes of hydrometeor mixing ratio and surface precipitation could be due to the collision-coalescence process between raindrops and snow and the graupel melting process.

• Atmosphere
• /
• v.22 no.3
• /
• pp.367-379
• /
• 2012

Measurements of $PM_{10}$ mass concentration, aerosol light scattering and absorption coefficients as well as aerosol size distribution were made to characterize the aerosol physical and optical properties at the two Korean WMO/GAW regional stations, Anmyeondo and Gosan. Episodic cases of the severe Asian dust events occurred in spring of 2009-2010 were studied. Results in this study show that the aerosol size distributions and optical properties at both stations are closely associated with the dust source regions and the transport routes. According to the comparison of the $PM_{10}$ mass concentration at both stations, the aerosol concentrations at Anmyeondo are not always higher than those at Gosan although the distance from the dust source region to Anmyeondo is closer than that of Gosan. The result shows that the aerosol concentrations depend on the transport routes of the dust-containing airmass. The range of mass scattering efficiencies at Anmyeon and Gosan was 0.50~1.45 and $0.62{\sim}1.51m^2g^{-1}$, respectively. The mass scattering efficiencies are comparable to those of the previous studies by Clarke et al. (2004) and Lee (2009). It is noted that anthropogenic fine particles scatter more effectively the sunlight than coarse dust particles. Finally, we found that the aerosol size distribution and optical properties at Anmyeondo and Gosan show somewhat different properties although the samples for the same dust_episodic events are compared.

• Korean Journal of Environment and Ecology
• /
• v.28 no.2
• /
• pp.105-112
• /
• 2014

During incubation, pelagic seabirds undergo large variations in their body mass as a result of concomitant fasting. In Procellariifomes undergoing important changes in body mass through the incubation, body mass regulation could be an important factor in behavioural decisions for changing activities during the incubation. The aim of this study was to investigate the effect of individuals' quality and incubation behaviour on their body mass regulation in Streaked Shearwaters Calonectris leucomelas breeding at Sasudo Island, in Jeju, South Korea during incubation period, June to August in 2013. In our results, we found that there was no relationship between the daily body mass loss and body size or condition of Streaked Shearwaters. However, the daily body mass loss increased significantly as the incubation bout increased. Moreover, the daily incubation bout was positively related to their body size. Consequently, although breeders' qualities were not related to their daily body mass loss during the incubation, the incubation behaviour affecting their daily body mass loss was regulated by their body size. Therefore, the body size of Streaked Shearwater breeders is one of important factors in their decisions for the incubation behaviour.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.5
• /
• pp.397-405
• /
• 2003

Heat and fluid flow in a compressor into which liquid refrigerant is injected for the purpose of reducing discharge gas temperature in a heat pump system has been numerically studied. A mechanistic approach encompassing liquid jet breakup and droplet evaporation has been performed to investigate the effects of liquid injection on the spacial and temporal variation of the gas temperature and pressure inside the compressor cylinder. Various parameters, such as liquid injection mass, time, duration and droplet size, are considered in the present study to elucidate the flow field inside the compressor. As the injection mass is increased, discharge gas temperature is decreased, while the pressure is increased due to the added mass of the injection. For the injected liquid mass corresponding to 15% of the total vapor mass in the cylinder, the discharge gas temperature drops by 22.4 K. It is observed that the droplet size plays a major role in the evaporation rate of the droplets that determines the degree of the discharge temperature drop.

• Journal of the Korean Society of Safety
• /
• v.9 no.1
• /
• pp.76-82
• /
• 1994

Combustion phenomena(characteristics) of organic solvents including various alcohols Immobilized on ceramic balls were studied. Experiments were performed by burning methyl, ethyl, and propyl alcohol immobilized on sands (particle size 0.35mm) and coramic balls(particle size 1~5mm) to measure mass burning rate, height burning rate and combustion temperature. The longer time from ignition to extinguishment was resualted from the larger particle size of ceramic balls and the smaller size of ceramic balls exhibited the higher mass burning rate. Of alcohols tested the relative magnitude of facilitation of combustion was methyl >ethyl >propyl. Combustion temperatare of alcohols, without regard to the types of alcohols, was not increased with smaller ceramic balls(up to 3mm of particle size). However, with larger ceramic balls, combustion temperatare of alcohols was increased by 40~5$0^{\circ}C$ and the highest combustion temperatare was obtained with sands(particle size 0.35mm). Also, second rising was occurred at the combustion time of I5-20min. and this second rising time was increased with the smaller particle. These results will be able to be used for petrochemical industries using particles to evaluate the danger of fire and explosion.

• Fire Science and Engineering
• /
• v.10 no.1
• /
• pp.44-48
• /
• 1996

Burning rate of immobilized methyl and ethyl alcohols on ceramic balls was studied. Experiments were performed by burning methyl, ethyl alcohols immobilized on sands (particle size 0.35mm) and ceramic balls (particle size 1-5mm) to measure mass burning rate, height burning rate and combustion temperature. The longer time from ignition to extinguishment was resulted from the larger particle size of ceramic balls and the smaller size of ceramic balls exhibited the higher mass burning rate. Of alcohols tested the relative magnitude of facilitation of combustion was methyl ＞ ethyl. Combustion temperature of alcohols, without regard to the types of alcohols, was not increased with smaller ceramic balls(up to 3mm of particle size). However, with larger ceramic balls, combustion temperatare of alcohols was increased by 40-50$^{\circ}$ and the highest combustion temperatare was obtained with sands (particle size 0.35mm).