• Journal of Biosystems Engineering
• /
• 제27권3호
• /
• pp.185-194
• /
• 2002

The objective of this study was to analyze a stability of sideways overturning of a forwarder developed by the Forestry Research Institute. The stability analysis was conducted using a multibody dynamic analysis program. VisualNastran Desktop. A solid model of the forwarder was constructed and its physical properties such as mass, mass center and mass moment of inertia were determined on 3D CAD modeler of the Solid Edge 8.0. 3D simulations of sideways overturning of the forwarder were also performed on the Visual Nastran using the solid model when it traveled across the slope and traversed over an up-hill side obstacle. Stability comparison between a bogie-wheeled and a 6-wheeled forwarders was also made and found that the bogie-wheeled forwarder was more stable than the 6-wheeled one on slopes. The safety speeds of the forwarder predicted by the simulation under various conditions can be used as a guideline for safe operations of forwarders in mountainous area. The technique of using a solid model for the sability analysis can also be applied successfully to other vehicles like agricultural tractors, loaders and construction equipments.

• 항공우주기술
• /
• 제6권1호
• /
• pp.201-208
• /
• 2007

75톤급 액체 로켓 엔진용 터보펌프의 연료펌프 및 터빈에 대한 회전체 동역학 설계가 이루어졌다. 후방 베어링으로부터 터빈까지의 거리를 베어링 하중 설계에 대한 설계 변수로 고려하였고, 터빈의 질량 및 전방 베어링과 후방 베어링의 강성을 변화시키면서 회전속도에 따른 비동기 고유진동수 해석을 수행하여 연료펌프/터빈의 임계속도를 고찰하였다. 터빈의 큰 관성으로 인하여 전방 베어링의 강성이 임계속도에 미치는 영향은 무시할만 한 것으로 나타났다. 후방 베어링의 강성이 $2{\times}10^{8}N/m$ 이상일 경우, 장축의 후방 베어링 간 축길이 및 20 kg이하의 터빈 질량에서 연료펌프/터빈 회전체의 임계속도는 설계속도 11,000 rpm 대비 70% 이상에 있음이 확인되었다.

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.19-27
• /
• 2018

It follows from the basic principles of mechanics of deformable solids relating to the strength, stability and propagation of elastic waves that the Earth's inner core cannot exist in the form of a spherical structure in the assumed thermobaric conditions and calculation values of physico-mechanical parameters. Pressure level reaches a value that is significantly greater than the theoretical limit of medium strength in the model approximations at the surface of the sphere of the inner core. On the other hand, equilibrium state of the sphere is unstable on the geometric forming at much lower loads under the influence of the "dead" surface loads. In case of the action of "follower" loads, the assumed pressure value on the surface of the sphere is comparable with the value of the critical load of "internal" instability. In these cases, due to the instability of the equilibrium state, propagation of homogeneous deformations becomes uneven in the sphere. Moreover, the elastic waves with actual velocity cannot propagate in such conditions in solid medium. Violation of these fundamental conditions of mechanics required in determining the physical and mechanical properties of the medium should be taken into account in the integrated interpretations of seismic and laboratory (experimental) data. In this case, application of the linear theory of elasticity and elastic waves does not ensure the reliability of results on the structure and composition of the Earth's core despite compliance with the required integral conditions on the mass, moment of inertia and natural oscillations of the Earth.

• Structural Engineering and Mechanics
• /
• 제55권3호
• /
• pp.655-674
• /
• 2015

In this paper, a new and simplified method is presented in which the natural frequencies of the uniform and non-uniform beams are calculated through simple mathematical relationships. The various vibration problems such as: Rayleigh beam under variable axial force, axial vibration of a bar with and without end discrete spring, torsional vibration of a bar with an attached mass moment of inertia, flexural vibration of the beam with laterally distributed elastic springs and also flexural vibration of the beam with effects of viscose damping are investigated. The governing differential equations are first obtained and then; according to a harmonic vibration, are converted into single variable equations in terms of location. Through repetitive integrations, the governing equations are converted into weak form integral equations. The mode shape functions of the vibration are approximated using a power series. Substitution of the power series into the integral equations results in a system of linear algebraic equations. The natural frequencies are determined by calculation of a non-trivial solution for system of equations. The efficiency and convergence rate of the current approach are investigated through comparison of the numerical results obtained with those obtained from other published references and results of available finite element software.

• 대한조선학회지
• /
• 제14권3호
• /
• pp.13-22
• /
• 1977

The hydrodynamic forces acting on a forced oscillating 2-dimensional cylinder on a free surface of a fluid of a finite depth are calculated by distributing singularities on the immersed body surface. And the Haskind-Newman relation in a fluid of a finite depth is derived. The wave exciting force of the cylinder to an oscillation is also calculated by using the above relation. The method is applied to a circular cylinder swaying in a water of finite depth, and then, to a rectangular cylinder heaving, swaying, and rolling. The results of above cases give a good agreement with those by earlier investigators such as Bai, Keil, and Yeung. Also, this method is applied to a Lewis form cylinder with a half beam-to-draft ratio of 1.0 and a sectional area coefficient of 0.941, and to a bulbous section cylinder which is hard to represent by a mapping function. The results reveal that the hydrodynamic forces in heave increase as the depth of a water decrease, but in sway or roll, the tendency of the hydrodynamic forces is difficult to say in a few words. The exciting force to heave for a bulbous section cylinder becomes zero at two frequencies. The added mass moment of inertia for roll is seemed to mainly depend on the sectional shape than the water depth.

• 대한기계학회논문집A
• /
• 제21권11호
• /
• pp.1957-1964
• /
• 1997

Torsional vibration is to vibrate strongly when the ignition pulses of the engine is excited with natural frequency of driveline. Torsional vibration like this can cause various noises as rattle and booming. For this study multi-degree of freedom analysis model of torsional vibration, which is combined with mass moment of inertia and torsional spring, was developed toward two wheel drive, four wheel drive and torsional vibration characteristics were compared and analyzed through the natural frequences, mode shapes and frequency response characteristics which was acquired by the simulation of it. The pertinence of that model was proved by the field test and the outcome of the simulations coincided with feeling test. Therefore, four wheel drive simulation model is considered to be useful thing for reducing torsional vibration of driveline and developing full-time four wheel drive vehicles.

• 대한기계학회논문집A
• /
• 제28권9호
• /
• pp.1359-1367
• /
• 2004

The purpose of this study is to predict the dynamic transmission error of the helical gear system. To do so, the equations of motion in the helical gear system which consists of motor, coupling, gear, torque sensor, and brake are derived. As the input parameters, the mass moment of inertia by a 3D CAD software and the equivalent stiffness of the bearings and shaft are calculated and the coupling stiffness is measured. The static transmission error as an excitation is calculated by in-house program. Dynamic transmission error is predicted by solving the equations of motion. Mode shape, the dynamic mesh force and the bearing force are also calculated. In this analysis, the relationship between the dynamic mesh force and the bearing force and mode shape behavior in gear mesh are checked. As a result, the magnitude of mesh force is highly related with the gear mesh behavior in mode shape. The finite element analysis is conducted to find out the natural frequency of gear system. The natural frequencies by finite element analysis have a good agreement with the results by equation of motion. Finally, dynamic transmission error is measured by the specially designed experiment and the results by equation of motion are validated.

• 대한기계학회논문집
• /
• 제10권5호
• /
• pp.689-697
• /
• 1986

본 연구에서는 3자유도(3방향의 병진운동만 고려) 고무마운트모형의 타당성을 검증하기 위하여, 먼저 고무자체의 물성치인 강성계수와 감쇠계수를 진동수와 초기변 형률에 따라 실험을 통해 구하였다. 질량행렬의 모든요소를 쉽게 구할 수 있는 간단 한 시험구조물을 제작하고 여기에 고무아운트를 부착하여 6자유도를 갖는 모의 엔진- 마운트계를 구성한 후 가진실험을 통해 얻은 오무드 매개변수들과 고무의 물성치를 이 용한 컴퓨터 시뮬레이션의 결과를 비교함으로써 고무아운트 모형의 타당성을 검증하였 다. 특히 본 연구에는 유압가진 실험으로부터 얻은 실험결과를 바탕으로 고무의 강 성계수를 주파수의 1차함수로 고려한 경우와 전진동수 영역에서 균일하다고 가정하는 경우를 비교하였다.

• 전기학회논문지
• /
• 제59권11호
• /
• pp.2073-2082
• /
• 2010

The 4-th generation of mobile communication aims to realize global, fast and mobile communication service. The satellite communication charges a key role in this field. In this study, an OTM(On-The-Move) antenna which is mounted on ground vehicles and is used for mobile communication between vehicle and satellite was addressed. Since vehicles move during communication, active antenna line-of-sight stabilization is a core technology to guarantee high satellite communication quality. Stabilization of a satellite tracking antenna which consists of 2-DOF gimbals, an elevation gimbal over an azimuth gimbal, was considered in this study. Various disturbance torques such as static and dynamic mass imbalance torques, variation of moment of inertia according to elevation angle, friction torque related to vehicle motion, equivalent disturbance torque due to antenna roll motion, etc. were analyzed. As a robust stabilization control, rate feedback with sliding mode control and position feedback with proportional+integral control was suggested. To compensate antenna roll motion, a supplementary roll rate feed forward control was included beside of the feedback control loop. The feasibility of the analysis and the proposed control design were verified along with some simulation results.

• 대한인간공학회지
• /
• 제30권6호
• /
• pp.715-725
• /
• 2011

Objective: This study is aimed at developing Articulated Human Models(AHM) using superquadrics to improve the geometric accuracy of the body shape. Background: The previous work presents the AHM with geometrical simplification such as ellipsoids to improve analysis efficiency. However, because of the simplicity, their physical properties such as a center of mass and moment of inertia are computed with errors compared to their actual values. Method: This paper introduces a three steps method to present the AHM with superquadrics. First, a 3D whole body scan data are divided into 17 body segments according to body joints. Second, superquadric fitting is employed to minimize the Euclidean distance between body segments and superquadrics. Finally, Fee-Form Deformation is used to improve accuracy over superquadric fitting. Results: Our computational experiment shows that the superquadric models give better accuracy of dynamic analysis than that of ellipsoid ones. Conclusion: We generate the AHM composed of 17 superquadrics and 16 joints using superquadric fitting. Application: The AHM using superquadrics can be used as the base model for dynamics and ergonomics applications with better accuracy because it presents the human motion effectively.