• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.102-109
• /
• 1986

Based on the Hartenberg-Denavit symbolic equation, which is one of equations for the kinematic analysis of three dimensional (3-D) linkage, a generalized kinematic motion equation is derived utilizing Euler angles and employing the coordinates transformation. The derived equation can feasibly be used for the motion analysis of any type of 3-D linkages as well as 2-D ones. In order to simulate the general motion of 3-D linkgages on digital computer, the generalized equation is programmed through the process of numerical analysis after converting the equation to the type of Newton-Raphson formula and denoting it in matrix form. The feasibility of theoretically derived equation is experimentally proved by comparing the results from the computer with those from experimental setup of three differrent but generally empolyed 3-D linkages.

• New & Renewable Energy
• /
• v.9 no.2
• /
• pp.23-29
• /
• 2013

Furnace and laser is currently the most important doping process. However furnace is typically difficult appling for selective emitters. Laser requires an expensive equipment and induces a structural damage due to high temperature using laser. This study has developed a new atmospheric pressure plasma source and research atmospheric pressure plasma doping. Atmospheric pressure plasma source injected Ar gas is applied a low frequency (a few 10 kHz) and discharged the plasma. We used P type silicon wafers of solar cell. We set the doping parameter that plasma treatment time was 6s and 30s, and the current of making the plasma is 70 mA and 120 mA. As result of experiment, prolonged plasma process time and highly plasma current occur deeper doping depth and improve sheet resistance. We investigated doping profile of phosphorus paste by SIMS (Secondary Ion Mass Spectroscopy) and obtained the sheet resistance using generally formula. Additionally, grasped the wafer surface image with SEM (Scanning Electron Microscopy) to investigate surface damage of doped wafer. Therefore we confirm the possibility making the selective emitter of solar cell applied atmospheric pressure plasma doping with phosphorus paste.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6715-6721
• /
• 2015

Recently, DNA data of missing person, killed person, and missing child continue to increase but most of statistical calculation for paternity confirmation is being done through manual methods or Excel. Therefore, we need development of a software which is able to facilitate both systematic management and effective analysis of Short Tandem Repeat (STR) derived from DNA data. Without extensive testing, through a twenty-month study was developed a web-based system which performs paternity analysis and kinship analysis easily based on the various options. The former uses an existing algorithm for paternity index and the latter does Identity by descent (IBD) formula. Due to our system validated over real datasets in terms of likelihood ratio and probability of paternity, it ensures increased reliability as well as effective management and analysis of DNA data in mass disaster. In addition, it includes advanced features such as an integrated environment, user-centered interface, process automation and so on.

• Korean Journal of Community Nutrition
• /
• v.3 no.1
• /
• pp.3-11
• /
• 1998

This study was aimed to evaluate any influence of environmental factors associated with feeding on infants' growth. One hundred infants(62 males and 38 females) aged 4-9 months were measured for length and were weighed. Their mothers were interviewed using questionnaires including general and environmental characteristics and maternal feeding attitude, ideal body habitus, infant's food behavior, and infant's food behavior, and infant's temperament. A further study was conducted on 29 infants at the time their ages reached 12 months. Their dietary intakes were assessed, and blood hemoglobin and serum ferritin concentrations were measured. Z-scores of weight-for-age(WAZ) and Z-scores of height-for-age(HAZ) of 4-9 month- old infants were not correlated with age, education level, income, weight, and height of their parents. Formula-fed infants had significantly lower WAZ and body mass index (BMI) than those of breast fed infants. WAZ was significantly correlated with maternal feeding attitude, but not with ideal body habitus, infant's food behavior or infant's temperament. WAZ of 12-months after birth because of supplementary foods introduced from 6 months of age. WAZ and BMI were positively correlated with blood hemoglobin concentration. Therefore, to ensure proper growth of infants, efforts should be given to postental factors such as breast-feeding, maternal feeding attitude, adequate iron status as well as prenatal factors. (Korean J Community Nutrition 3(1) : 3∼11, 1998)

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.59 no.3
• /
• pp.359-363
• /
• 2014

Soybean seed is a good source of plant protein in human consumables such as baby formula and protein concentrate. The seeds contain an abundance of storage proteins, namely ${\beta}$-conglycin and glycinin that account for ~ 70-80% of the total seed protein content. Proteome profiling has been proved to be an efficient way that can help us to investigate the seed storage proteins. In the present study, the seeds were removed from the pods and the cotylendonary tissues were separated from the testa for proteome analysis in order to investigate the seed storage proteins. A systematic proteome profiling was conducted through one-dimensional gel electrophoresis followed by MALDI-TOF-TOF mass spectrometry in the seeds (cotyledonary tissue) of soybean genotypes. Two dimensional gels stained with CBB, a total of 10 proteins were identified and analyzed using MASCOT search engine according to the similarity of sequences with previously characterized proteins along with the UniProt database. A total of ten proteins such as glycinin Gy4 precursor, glycinin G3 precursor, glycinin G1 precursor, glycinin chain A2B1a precursor, glycinin chain A2B1a precursor were identified in our investigation. However, the glycinin subunit may be considered to play important roles in soybean breeding and biochemical characterization. In addition, the improved technique will be useful to dissect the genetic control of glycinin expression in soybean.

• Korean Journal of Pharmacognosy
• /
• v.49 no.1
• /
• pp.76-83
• /
• 2018

A traditional herbal formula, Gyeji-tang has been used to treat the early colds, headache, chills, and fever in Asian countries. In this study, we were performed simultaneous determination of the 14 bioactive marker compounds, gallic acid, spinosin, paeoniflorin, albiflorin, liquiritin apioside, liquiritin, 6'''-feruloylspinosin, liquilitigenin, coumarin, cinnmamic acid, benzoylpaeoniflorin, cinnamaldehyde, glycyrrhizin, and 6-gingerol in Gyeji-tang using an ultra-performance liquid chromatography-electrospray ionization-mass spectrometry (UPLC-ESI-MS/MS). Analytical column was used a Waters Acquity UPLC BEH $C_{18}$ analytical column ($2.1{\times}100mm$, $1.7{\mu}m$) and maintained at $45^{\circ}C$ with a flow rate of 0.3 mL/min. The mobile phase consists of 0.1% (v/v) formic acid in water and acetonitrile with gradient elution. The MS analysis was conducted using multiple reaction monitoring in the positive and negative modes by a Waters ACQUITY TQD LC-MS/MS system. The calibration curves of 14 bioactive marker compounds showed linearity with correlation coefficients ${\geq}0.9798$. The limits of detection and quantification values were in the range of 0.11-6.66 ng/mL and 0.34-19.99 ng/mL, respectively. As a result of the analysis using the established LC-MS/MS method, the amounts of tested 14 compounds in the lyophilized Gyeji-tang sample were detected up to $85.7{\mu}g/g$. These results may be useful for quality assessment of a traditional herbal formulas.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.79-79
• /
• 2001

백판지는 포장용기로 사용되기 때문에 인쇄적성 이외에 다양한 후가공적성이 요구 된다. V Varnish Coating도 이러한 후가공적성 중의 하나로서 국내 인쇄소에서는 기계 코팅으로 불리 우며, 목적은 표면에 고분자수지 피막을 입힘으로써 인쇄물의 광택을 높여서 상품가치를 높이고 수운침투와 같은 외부환경의 변화로부터 상품을 안전하게 보관하기 위함이다. arnish C Coating은 인쇄기의 마지막 Unit에서 인쇄와 동일한 방식으로 진행되는데, 코팅액의 배합은 인쇄소와 인쇄물에 따라 상이하다. 본 연구는 Varnish Coating(OI하 기계코팅) 광택향상을 통 한 품질개선 목적으로 수행되었다. 기계 코팅의 특 성 을 파 악 하 기 위 해 서 Gas Chromatography / Mass Spectrometer와 FT -IR Sp e ectrometer를 사용하여 성문운석을 실시해본 결과 코팅액으로 사용되는 광택바니스는 아크 랄과 페놀수지를 툴루엔 계열의 용매에 녹인 용액이고, 흐$\mid$석제로 쓰이는 인쇄바니스는 스티 렌수지를 동일한 용매에 녹인 용액으로 조사되었다. 기계코팅광택 저하현상의 원인파악을 위해서 도공층의 공극구조를 Mercury Porosimeter를 이용하여 파악한 결과 기공의 부피가 상 대적으로 크게 나타났다. 위의 결과를 토대로 기계코팅광택 저하는 코팅액이 과도한 기공부피를 갖는 도공층 내부 로 대부분 홉수되고 표면에 적은 양만이 잔류하기 때문으로 판단하고 해결방안은 도공층의 기공부피를 줄이는 쪽으로 정하였다. Mayor Coater와 QC를 이용하여 Coating Color Formula t tion 번경실힘을 진행하여 도공지 물성을 분석하였다. 그 결과 Double Coating의 Top Color에 서 강력한 상호작용을 하는 Protein과 콜레이를 감량 하고 경질탄산칼숨을 배제하여 기공의 부피를 줄인 경우 기계코팅광택 향상효과가 두드러지게 나타났다. 이러한 Lab 실험을 바탕으로 결정된 Color Formulation에 대한 현장실험을 진행하였고 Lab 평가 및 실인쇄 평가 결과 원하는 수준의 기계코팅광택 향상을 얻을 수 있었다. 몇 차례의 현장실험과 Long-Run Test한 제품들에 대한 물성을 문석한 결과 기계코팅굉택은 인쇄 광택과 같은 경향을 나타냈으며 실협실적으로 간단하게 측정되는 물성 중에서 Air Permeability와 강한 음의 상관관계롤 보였다.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.8
• /
• pp.79-88
• /
• 2012

In this study, the tunnel loads acting on the concrete lining are analyzed by comparing three methods - Terzaghi table, Terzaghi formula and Ground-Lining Interaction (G.L.I) model. The tunnel loads are analyzed by FLAC 2D. And the G.L.I model is analyzed under various rock mass ratings, tunnel depths (20~80m) and in-situ stress ratios ($K_0$=0.5~2.0). Terzaghi's method can be applied only to weathered rocks and soils, and cannot reflect the effect of various tunnel depths and in-situ stress ratio. The proposed G.L.I model can not only be applied to various ground conditions, but also relieves the tunnel loads by up to 30%.

• Journal of Radiation Protection and Research
• /
• v.43 no.2
• /
• pp.75-84
• /
• 2018

Background: Gamma-ray spectrometry helps in radiation shielding problems and different applications of radioisotopes. Experimental arrangements including broad beam geometries are widely used. The aim is to investigate and evaluate the ${\gamma}-ray$ spectra via attenuation by environmental materials. Materials and Methods: The photo peak to nominated parts in the ${\gamma}-ray$ spectra and the attenuation coefficients ${\mu}_b/{\rho}$ from broad beam geometries are measured for the materials water, soil, sand and cement at the energies 0.662, 1.25, and 1.332 MeV with a $3{^{\prime}^{\prime}}{\times}3{^{\prime}^{\prime}}$ NaI(Tl) detector. Results and Discussion: The ${\gamma}-ray$ spectra vary according to changes in the effective atomic number $Z_{eff}$ of the attenuator, the photon energy and the solid angle. The peak to total ratios are the most sensitive parts to variations in the experimental conditions and overturn in the region 0.663 MeV to 1.332 MeV. This is indicated as inversion trend. The results are discussed in view of $Z_{eff}$ and the experimental conditions. The intensity build-up is larger at the lower energy and larger scattering angles in agreement with Klein-Nishina formula and other results. The build-up factor B is$${\sim_=}$$1 at high ${\gamma}-energies$ and small scattering angles. Conclusion: The sensitivity to material characteristics decrease gradually from peak: to total, to Compton valley, to Compton plateau ratios. Rigorous collimation is necessary at small energies. Cement, of the largest $Z_{eff}$, is characterized by the maximum broad beam mass attenuation coefficients ${\mu}_b/{\rho}$. The obtained results provide information to decide for the suitable experimental set-up based on aim of the work.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.694-701
• /
• 1990

The cycle of heat engine which produces the maximum power output is constructed when heat sources are finitely constant, and the maximum power as a thermodynamic limit of the engine, is obtained. The characteristics of the maximum power cycle are as follows, which represent the operation conditions and design conditions of the heat engine to produce the maximum power output. In heat exchangers, the temperature profiles of the heat source and the working fluid have the same functional formula and the ratio of the working fluid temperature to the heat source temperature is constant. When heat capacity flow rates(product of the specific heat and the mass flow rate) of the working fluid as well as the heat source are constant, the values of those of working fluid exist between those of two heat sources. The relation of the temperature and the heat capacity flow rate is established without the states of the heat sources and the capacities of heat exchangers, which is ( $T_{h}$/ $T_{H}$)( $C_{h}$/ $C_{H}$)=( $T_{1}$/ $T_{L}$)( $c_{1}$/ $c_{L}$)=1. The capacity of the heat exchanger of hot side is equal to that of cold side regardless of the states of the heat sources and the total capacities of heat exchangers.hangers.ers.