• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.807-809
• /
• 1998

We give pressure stimulation into organic thin films and detect the induced displacement current, In processing of a device manufacture, we can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/organic thin films(Kapton-Polyimide)/Au and I-V properties of the device is measured from 0(V) to +5(V). The maximum value of measured current is increased as the number of accumulated layers are decreased. The resistance for the number of accumulated layers, the energy density for an input voltage show desired results.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.53-59
• /
• 2010

Preliminary design of a ground plate, a device installed close to the aircraft model for wind tunnel test to simulate the ground effect, was performed by a numerical simulation. A two-dimensional numerical study was performed initially to decide the optimal leading edge and flap configurations. Then, three-dimensional studies were conducted to decide the optimal flap deflection angle for pressure distribution reduction since the plate and the plate supporting system generate static pressure difference between the upper and lower flow regions. Three-dimensional simulation additionally studied the effect of the clearance between the plate and the wind tunnel side wall. For the efficiency of computation, half model was simulated and a symmetric boundary condition was applied on the center plane. Based on the preliminary design, a ground plate was designed, manufactured and tested at the Korea Aerospace Research Institute(KARI) wind tunnel. The measured pressure differences versus flap deflection angle agreed well with the predicted results.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.494-499
• /
• 2001

This research carried out the experimental manufacture of the improved fastening device and its performance test as well as the structural improvement of the prototype of a new type of fastening device developed through G7 Project during the first year of the second phase. Firstly, a supplementary design for each part of the prototype was carried out in order to improve its performance and a structural analysis in order to review the stress on the fastening spring. Secondly, another prototype was manufactured and then a performance test was carried out with the criteria used for the same kind of test on the authorized ones, both at home and abroad. Finally, the usability of the device was reviewed by comparing above-mentioned test result with that of those already under commercial use.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.110-116
• /
• 2015

A 3D camera-based on-site work-related musculoskeletal disorder risk assessment(WMDs) tool has been developed. The device consists of Kinect a 3D camera manufactured by Microsoft, a servo-motor, and a mobile robot. To complement inherent narrow field of view(FOV) of Kinect, Kinect is rotated according to PID servo-control algorithm by a servo-motor attached underneath, to track movement of a subject, producing skeleton-based motion data. With servo-control, full 360 degrees tracking of a test subject is possible by single Kinect. It was found from experimental tests that the proposed device can be successfully employed for on-site WMDs risk assessing tool.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.1
• /
• pp.40-45
• /
• 2008

This paper proposes a tube pump composed of small-sized cams and followers for an implantable intrathecal drug infusion device. Each followers is driven by a cam and liquid is discharged by a sequential reciprocal motion of the followers. The advantage of this structure is that it allows the pump to be clean and valveless. To design a small-sized, low power pump some analysis were performed to determine the design parameters of the cam, follower and the tube. To verify the feasibility of the experiment, a prototype was manufactured and its operating characteristics were investigated. Experimental results were in accordance with the expected results obtained from analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.134-139
• /
• 2002

We have made known the study of shape development of interference device for vehicle noise control. It's primary object greatly attenuate the noise due to transport vehicle by small products installed on the noise barrier edge. Also, it is able to improve the insertion loss of a noise barrier without increasing the height. The present time, we set up a newly manufactured products on the noise barrier edge and testify to it's the performance make use of an experiment and evaluation for the reduction of highway traffic noise. In this paper the frequency characteristic of interference device of noise barriers with attached newly developed products in terms of shape, absorptive material and split panel, are examined using field test at highway.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1998.11a
• /
• pp.112-115
• /
• 1998

We investigate the qualities of organic materials by which can manufacture organic thin films for solar cells and make thin films for insulation layers of an insulated cable. We give pressure stimulation into organic thin films and detect the induced displacement current. In processing of a device manufacture, We can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/organic thin films(polyimide)/Au and I-V characteristic of the device is measured from 0[V] to +5[V]. The maximum value of measured current is increased as the number of accumulated layers are decreased. The resistance for the number of accumulated layers, the energy density for an input voltage show desired results, and the insulation of a thin film is better as the interval between electrodes is larger.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.417-422
• /
• 2002

One of the major limitations of productivity and quality in metal cutting is the machining accuracy of machine tools. The machining accuracy is affected by geometric errors, thermally-induced errors, and the deterioration of the machine tools. Geometric and thermal errors of machine tools should be measured and compensated to manufacture high quality products. In metal cutting, the machining accuracy is more affected by thermal errors than by geometric errors. In this study, the compensation device and temperature-based algorithm have been implemented on the machining center in order to compensate thermal error of machine tools under the real-time. The thermal errors are predicted using the neural network and multi-regression modeling methods. In order to compensate thermal characteristics under several operating conditions, experiments performed with five gap sensors and manufactured compensation device on the horizontal machining center.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.491-494
• /
• 1999

We have examined the electrical properties of arachidic acid Langmuir (L) films by using a displacement current measuring technique with pressure stimulation. We give pressure stimulation into organic thin films and detect the Induced displacement current. The structure of manufactured device is Au/arachidic acid/Al, the number of accumulated layers are 17, 19 and 21. Also, we then examined of the MIM device by means of I-V The I-V characteristic of the device is measured from 0 to +1[V]. The insulation property of a thin film is better as the distance between electrodes is larger.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.96-104
• /
• 1997

The objective of this research project was to develop the wooden footpath block to reuse of wood waste. Some physical and mechanical properties of the wooden block such as water absorption, thickness swelling, modulus of rupture, internal bond, density profile and impact resistance were studied. Water absorption and thickness swelling of the wooden block were greatly reduced when the wooden block was pressed inside the forming device than by conventional hot pressing. Also, Modulus of rupture and internal bond of the wooden block were increased greatly when the pressing was completed inside the forming device. The density profile of the wooden block was improved up to 93.5%, minimum to average density ratio. The wooden block manufactured in this study have excellent physical and mechanical prperties in comparison with existing wood based materials. So, these wooden blocks are applicable to footpth block or other exterior members.