• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.4
• /
• pp.33-37
• /
• 2007

In this paper, a dynamic analysis of a helicopter landing gear with considering flexible structural modes has been investigated. The main body of the helicopter has been modeled as a flexible body using FEM code, then a few selected vibration modes of the helicopter main body have been used as basis for the dynamic analysis of the helicopter landing gear. The simulation of dynamic analysis was carried out on the base of ADAMS aircraft module. It has been found by a series of simulation that the flexible structural modes has a significant effect on the dynamic characteristics of helicopter landing gear as the flexibility of the main body is increased.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.55-59
• /
• 2013

Transverse vibrations of ship's aft end and deckhouse among the various modes of hull structures are induced mainly by transverse exciting forces and moments of main engine such as ${\times}$ and h-moment. Avoidance of resonance should be made in a intial design stage in case there is a prediction for resonance between main engine and transverse modes of deckhouse. This study shows a case of change in type of main engine from 12 cylinders to 10 without modification of hull structures in engine room requested by a shipowner of 8,600 TEU class container carrier and proposes a guide to the effective ways of structural arrangement for avoiding resonance between transverse exciting force and surrounding structures of main engine in engine room through case studies.

• International Journal of Automotive Technology
• /
• v.8 no.4
• /
• pp.477-481
• /
• 2007

In this article we present a new, reference model based, unified strategy for engine control. Three main modes are considered: first is the driver control mode where the driver controls the engine via the pedal position; second is the dashpot mode, that is, when the driver takes his foot off the pedal; and, lastly is the idle speed control mode. These modes are unified so that seamless transitions between modes now becomes possible. The unification is achieved due to the introduction of a reference model for the engine speed whereby only the desired engine speed is different for different modes while the structure of the control system remains the same for all the modes. The scheme includes an observer that estimates unknown engine load torque. A proof of robustness with respect to unknown load disturbances both within the operating modes and during intermode transitions is given.

• Korean Journal of Hydrosciences
• /
• v.1
• /
• pp.99-106
• /
• 1990

An extensive biological nutrient removal pilot plant study of anoxic/anaerobic/ aerobic treatment process was conducted to eastblish an optimum operational mode using primary dffluent. Two operational modes, (1) Qr/Q was 3.0 and maintaining EMLSS of 3100 mg/L in which the best operational results were obtained from previous bench scale study using synthetic wastewater (2) Qr/Q was 0.5 and EMLSS of 2200 mg/L which was compatible with the main plant, were Compared and evaluated for removal of nitrogen and/or phosphorous under field conditions. The nitrogen removal increased with increasing recycle ratios, but the phosphorous removal revealed more consistent results with 83percent removal efficiency in the second mode compared with 80 percent in the first mode. Above all, the two modes equally showed good BOD and nitrogen removals by nitrification-denitrification processes. It was also observed that no scum formed in the pilot plant and the sludge exhibited excellent settling characteristic all the time. The modified biological nutrient removal train can be adopted to the main plant without any major changes of their operational modes.

• Journal of Korean Society of Transportation
• /
• v.11 no.2
• /
• pp.45-62
• /
• 1993

The major objective of this study is to analyze the differences between operating costs of teleconferencing and alternative transportation modes for the conference in major compaines. Alternative transportation modes include road, rail, and air transportation mode. A case study is conducted using the data gathered for Pohang Steel Coperations. The main results are: (1) the operating cost of the teleconferencing is cheaper than operating cost of transportation modes when the number of teleconferencing are over 12 frequencs, and the number of person are over 15. Results reveal that teleconferencing turns out to be effective means of conference. (2) the amount of differences of operating costs on teleconsferencing and transportation modes gets higher according to the time elapsed. In particular, when teleconferencing cost is compared to operating cost of road transportation, it is found that the cost saving of 2.75 billion won in year 2001 can be realized.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.1035-1046
• /
• 2015

This study presents a practical implementation of a multi-mode two-phase interleaved boost converter for fuel cell electric vehicle application. The main operating modes, which include two continuous conducting modes and four discontinuous conducting modes, are discussed. The boundaries and transitions among these modes are analyzed with consideration of the inductor parasitic resistance. The safe operational area is analyzed through a comparison of the different operating modes. The output voltage and power characteristics with open-loop or closed-loop operation are also discussed. Key performance parameters, including the DC voltage gain, input ripple current, output ripple voltage, and switch stresses, are presented and supported by simulation and experimental results.

• Steel and Composite Structures
• /
• v.46 no.2
• /
• pp.221-236
• /
• 2023

In order to study the seismic response of the main plant of steel reinforced concrete (SRC) structure of the CAP1400 nuclear power plant under the influence of different high-mode vibration, the 1/7 model structure was manufactured and its dynamic characteristics was tested. Secondly, the finite element model of SRC frame-bent structure was established, the seismic response was analyzed by mode-superposition response spectrum method. Taking the combination result of the 500 vibration modes as the standard, the error of the base reactions, inter-story drift, bending moment and shear of different modes were calculated. Then, based on the results, the influence of high-mode vibration on the seismic response of the SRC frame-bent structure of the main plant was analyzed. The results show that when the 34 vibration modes were intercepted, the mass participation coefficient of the vertical and horizontal vibration mode was above 90%, which can meet the requirements of design code. There is a large error between the seismic response calculated by the 34 and 500 vibration modes, and the error decreases as the number of modes increases. When 60 modes were selected, the error can be reduced to about 1%. The error of the maximum bottom moment of the bottom column appeared in the position of the bent column. Finally, according to the characteristics of the seismic influence coefficient αj of each mode, the mode contribution coefficient γj•Xji was defined to reflect the contribution of each mode to the seismic action.

• Korea Trade Review
• /
• v.46 no.5
• /
• pp.115-130
• /
• 2021

The main purpose of this study is to analyze the causal relationship between import-export goods and transportation modes. To this end, five major commodity groups were selected from 2010 to 2018 such as Machinery and transport equipment (SITC 7), manufactured goods classified chiefly by material (SITC 6), chemicals and related products, n.e.s. (SITC 5), mineral, fuels, lubricants, and related materials (SITC 3), and miscellaneous manufactured articles (SITC 8). And using the panel VECM, the difference between transportation modes such as ports and airports was compared and analyzed through panel granger causality, Impulse response function, Forecasting error variance decomposition. As a result, it is confirmed that the causal relationship between major product groups and transportation modes showed different causal relationships depending on the characteristics of port and air transportation.

• Journal of Distribution Science
• /
• v.16 no.1
• /
• pp.59-71
• /
• 2018

Purpose - Recognizing the importance of small and medium enterprises and venture enterprises for the domestic economy, the purpose of the present study is to select factor termed export modes from among various export success strategies and factors that can help those enterprises secure export competitiveness in the world market to analyze the effects of export modes on the amounts of exports and periods until export after the foundation of those enterprises. Research design, data, and methodology - A structured questionnaire was used as a tool to derive the purpose of the study, and a questionnaire survey was conducted using a mobile survey technique that facilitated the distribution of questionnaire sheets and the collection of results. The main methodology used is crossover analysis, and the regression analysis technique was applied to verify the study results derived, thereby securing the reliability and validity of the final results derived. Results - Small and medium venture enterprises with shorter periods of time until the first export success after establishment adopted direct export modes more frequently, and those enterprises with larger amounts of the first export after establishment adopted direct export modes more frequently. The results of quantitative analysis, indicating that 66.1% of those enterprises with an export amount exceeding one billion won adopted direct export modes, can be said to support the foregoing. The crossover analysis results derived as such were reanalyzed using the PPML regression analysis technique to quantitatively identify that the amounts of the first export of enterprises that adopted direct export modes were larger than those of enterprises that adopted indirect export modes by 120%. Conclusions - The present study implies differentiated values in three aspects. First, the present study investigated and presented the export success factors and strategies of small and medium venture enterprises in a total of 14 countries in the Asian region, European region, North American region, African region, and South American region. Second, it intensively investigated five export modes to identify and verify that they were affecting the export success of small and medium venture enterprises. Third, based on the results of the investigation, the present study presented two marketing implications in the pragmatic aspect.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.864-871
• /
• 2015

Recently, one of the main research on the power distribution system is the microgrid. The microgrid is a combination of power sources and loads, which is controllable and has separable connection. The main objective of microgrid is the deployment of the renewable clean energy and the enhancement of load-side reliability. The modern power sources and loads have DC I/O interfaces, which is the major advantage of DC microgrid compared to the conventional AC grid. The components in the microgrid have diverse features, so there is need of proper coordination control. For achieving economic feature, the active power of renewable energy resources is regarded as major control parameter and the whole operation modes of DC microgrid are defined, and the proper operations of each component are described. From the inherent characteristics of DC, there are two control variables: voltage and active power. Through analysis of operation modes, it is possible to determine exact control objectives and optimized voltage & power control strategy in each mode. Because of consideration of whole operation modes, regardless of the number and capacity of components, this coordination control method can be used without modification. This paper defines operation mode of DC microgrid with several DC sources and suggests economic and efficient coordinated control methods. Simulation with PSCAD proves effectiveness.