• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.50-59
• /
• 2006

The risk of fault reactivation in the Gippsland Basin was calculated using the FAST (Fault Analysis Seal Technology) technique, which determines fault reactivation risk by estimating the increase in pore pressure required to cause reactivation within the present-day stress field. The stress regime in the Gippsland Basin is on the boundary between strike-slip and reverse faulting: maximum horizontal stress $({\sim}\;40.5\;Mpa/km)$ > vertical stress (21 Mpa/km) ${\sim}$ minimum horizontal stress (20 MPa/km). Pore pressure is hydrostatic above the Campanian Volcanics of the Golden Beach Subgroup. The NW-SE maximum horizontal stress orientation $(139^{\circ}N)$ determined herein is broadly consistent with previous estimates, and verifies a NW-SE maximum horizontal stress orientation in the Gippsland Basin. Fault reactivation risk in the Gippsland Basin was calculated using two fault strength scenarios; cohesionless faults $(C=0;{\mu}=0.65)$ and healed faults $(C=5.4;\;{\mu}=0.78)$. The orientations of faults with relatively high and relatively low reactivation potential are almost identical for healed and cohesionless fault strength scenarios. High-angle faults striking NE-SW are unlikely to reactivate in the current stress regime. High-angle faults oriented SSE-NNW and ENE-WSW have the highest fault reactivation risk. Additionally, low-angle faults (thrust faults) striking NE-SW have a relatively high risk of reactivation. The highest reactivation risk for optimally oriented faults corresponds to an estimated pore pressure increase (Delta-P) of 3.8 MPa $({\sim}548\;psi)$ for cohesionless faults and 15.6 MPa $({\sim}2262\;psi)$ for healed faults. The absolute values of pore pressure increase obtained from fault reactivation analysis presented in this paper are subject to large errors because of uncertainties in the geomechanical model (in situ stress and rock strength data). In particular, the maximum horizontal stress magnitude and fault strength data are poorly constrained. Therefore, fault reactivation analysis cannot be used to directly measure the maximum allowable pore pressure increase within a reservoir. We argue that fault reactivation analysis of this type can only be used for assessing the relative risk of fault reactivation and not to determine the maximum allowable pore pressure increase a fault can withstand prior to reactivation.

• Journal of the Korean Society of Groundwater Environment
• /
• v.6 no.2
• /
• pp.59-65
• /
• 1999

Both the groundwater changes due to different pumping rates and the geochemistry of thermal waters in the Suanbo area are considered in this study. The observation of groundwater level change since 1991 shows that the change is directly correlated with pumping rates of thermal waters and reveals the retardation of ca. 5 weeks after pumping. The hydrogeological aquifer in the area is under reducing condition. The thermal waters are of Na-HCO$_3$ type. and are alkaline (pH=8.5∼8.7) with low TDS values (274∼284 mg/l) and high concentrations of Na (68∼72 mg/l). F (6.4∼8.9 mg/l), and HCO$_3$(136∼146 mg/l). Oxygen and hydrogen isotope ratios of thermal water indicate a meteoric water origin. The activities of Rn-222 and Ra-226 in both thermal water and local groundwater were determined to delineate possible geochemical controls on the Rn-222 and Ra-226. The Rn-222 concentrations are several orders of magnitude greater than the Ra-226 concentrations. The concentrations of Rn-222 range from 190 to 7.490 pCi/1 with an average of 2,522 pCil/l. and those of Ra-226 average 0.32 pCi/1 with the range from 0.25 to 0.42 pCi/1. The concentrations of Rn-222 and Ra-226 are inversely correlated with EC and alkalinity. The pH it positively correlated with Ra-226. The correlation between Rn-222 and Ra-226 is poor. Thermal waters in the study area are produced from highly fractured phyllite. The thermal water qualify. CSAMT (controled-source audiofrequency magnetotelluric) prospecting, and petrological evidences, however, indicate that the heat is possibly transmitted through deep normal faults reaching a deep granite batholith, and the phyllite acts only as a groundwater pathway.

• Journal of Venture Innovation
• /
• v.3 no.1
• /
• pp.117-142
• /
• 2020

The purpose of this study is to explore the factors affecting the 6th industry experience by Schmitt experience model. The newly introduced variables are the cognitive experience, emotional experience, and social experience that are reconstructed based on Schmitt's experience theory and gender, family as a moderrating variable and trust as a mediation variable. In addition to experience intention. The hypothesis was set as follows. the experience factors that are the cognitive factor, the emotional factor, and the social factor will have a positive(+) influence on the intention to experience. Mooring factors will have a negative(-) effect on intention to experience. For statistical analysis, SPSS 24 and AMOS 23 statistical packages were used to test the research hypothesis. The research was based on 320 questionnaire data and tested by 314 valid responses were analyzed. As a result of the research, First, cognitive, emotional, and social factors had positive(+) effects on experience intention. Among the factors that directly affect the experience intention, the magnitude of influence appeared in the order of cognitive factors > social factors > emotional factors > mooring factors. Second, mooring factors have negative(-) effects on experience intention. Third, Trust has been partially influenced by factors of attraction, cognitive, emotional, and social. Fourth, there are significant statistical differences between men and women in cognitive and mooring factors in the path differences. Fifth, Social factors and mooring factors differed significantly in the composition of the household. Social factors with significant differences in path analysis have also been statistically demonstrated. The results of this study are academically verified that the cognitive, emotional, and social factors have an important influence on the experience intention in the 6th industry experience and the Schmitt's experience model proposed in this study is useful framework of analysis. In practical terms, it could provide implications for what factors should be strategically and marketingly focused to activate the 6th industry experience.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.4
• /
• pp.5-16
• /
• 2018

In the current study, the engineering behaviour of prebored and precast steel pipe piles was examined from a series of full-scale field measurements by conducting static pile load tests, dynamic pile load tests (EOID and restrike tests) and Class-A and Class-C1 type numerical analysis. The study includes the pile load - settlement relations, allowable pile capacity and shear stress transfer mechanism. Compared to the allowable pile capacity obtained from the static pile load tests, the dynamic pile load tests and the numerical simulation showed surprisingly large variations. Overall among these the restrike tests displayed the best results, however the reliability of the predictions from the numerical analysis was lower than those estimated from the dynamic pile load tests. The allowable pile capacity obtained from the EOID tests and the restrike tests indicated 20.0%-181.0% (avg: 69.3%) and 48.2%-181.1% (avg: 92.1%) of the corresponding measured values from the static pile loading tests, respectively. Furthermore, the computed results from the Class-A type analysis showed the largest scatters (37.1%-210.5%, avg: 121.2%). In the EOID tests, a majority of the external load were carried by the end bearing pile capacity, however, similar skin friction and end bearing capacity in magnitude were mobilised in the restrike tests. The measured end bearing pile capacity from the restrike tests were smaller than was measured from the EOID tests. The present study has revealed that if the impact energy is not sufficient in a restrike test, the end bearing pile capacity most likely will be underestimated. The shear stresses computed from the numerical analysis deviated substantially from the measured pile force distributions. It can be concluded that the engineering behaviour of the pile is heavily affected if a slime layer exists near the pile tip, and that the smaller the stiffness of the slime and the thicker the slime, the greater the settlement of the pile.

• KDI Journal of Economic Policy
• /
• v.31 no.2
• /
• pp.127-153
• /
• 2009

There is a growing concern about potential harmful effect of second-hand or environmental tobacco smoking. As a result, smoking bans in workplace become more prevalent worldwide. In Korea, workplace smoking ban policy become more restrictive in 2003 when National health enhancing law was amended. The new law requires all office buildings larger than 3,000 square meters (multi-purpose buildings larger than 2,000 square meters) should be smoke free. Therefore, a lot of indoor office became non smoking area. Previous studies in other counties often found contradicting answers for the effects of workplace smoking ban on smoking behavior. In addition, there was no study in Korea yet that examines the causal impacts of smoking ban on smoking behavior. The situation in Korea might be different from other countries. Using 2001 and 2005 Korea National Health and Nutrition surveys which are representative for population in Korea we try to examine the impacts of law change on current smoker and cigarettes smoked per day. The amended law impacted the whole country at the same time and there was a declining trend in smoking rate even before the legislation update. So, the challenge here is to tease out the true impact only. We compare indoor working occupations which are constrained by the law change with outdoor working occupations which are less impacted. Since the data has been collected before (2001) and after (2005) the law change for treated (indoor working occupations) and control (outdoor working occupations) groups we will use difference in difference method. We restrict our sample to working age (between 20 and 65) since these are the relevant population by the workplace smoking ban policy. We also restrict the sample to indoor occupations (executive or administrative and administrative support) and outdoor occupations (sales and low skilled worker) after dropping unemployed and someone working for military since it is not clear whether these occupations are treated group or control group. This classification was supported when we examined the answers for workplace smoking ban policy existing only in 2005 survey. Sixty eight percent of indoor occupations reported having an office smoking ban policy compared to forty percent of outdoor occupation answering workplace smoking ban policy. The estimated impacts on current smoker are 4.1 percentage point decline and cigarettes per day show statistically significant decline of 2.5 cigarettes per day. Taking into account consumption of average sixteen cigarettes per day among smokers it is sixteen percent decline in smoking rate which is substantial. We tested robustness using the same sample across two surveys and also using tobit model. Our results are robust against both concerns. It is possible that our measure of treated and control group have measurement error which will lead to attenuation bias. However, we are finding statistically significant impacts which might be a lower bound of the true estimates. The magnitude of our finding is not much different from previous finding of significant impacts. For cigarettes per day previous estimates varied from 1.37 to 3.9 and for current smoker it showed between 1%p and 7.8%p.

• Journal of the Korean earth science society
• /
• v.28 no.4
• /
• pp.478-490
• /
• 2007

With groundwater data of seawater intrusion monitoring network in coastal areas of Korea's main land, we analyzed types of seawater intrusion through the coastal aquifer. The data including groundwater level, temperature and electrical conductivity obtained from 45 monitoring wells at 25 watershed regions were evaluated. Based on statistical analysis, correlation analysis and variation type analysis, groundwater levels were mainly affected by rainfall and artificial pumping. About 78% of the monitoring wells showed average temperature higher than $15^{\circ}C$ and about 58% of them showed minimum variations less than $0.2^{\circ}C$. Electrical conductivities showed a large magnitude of variation and irregular characteristics compared with groundwater levels and temperatures. Average electrical conductivities lower than $2,000\;{\mu}S/cm$ were observed at 28 monitoring wells while those of higher than $10,000\;{\mu}S/cm$ were done at 9 monitoring wells. From the cross-correlation analysis, groundwater levels were mostly affected by precipitation while temperature and electrical conductivity showed very low correlation. Meanwhile tidal variations strongly affected the groundwater levels comparing to precipitation. We classified the long-term monitoring data according to variation types such as constant process, linear trend, cyclic variation, impulse, step function and ramp. Impulse type was dominant for variations of groundwater level, which was largely affected by rainfall or artificial pumping, the constant process was dominant for temperature. Compared with groundwater level and temperature, electrical conductivities showed various types like linear trend, step function and ramp. According to the discrepancy of variation characteristics for monitoring data at each well in the same region, periodical analysis of monitoring data is essentially required.

• Journal of Oral Medicine and Pain
• /
• v.32 no.1
• /
• pp.105-111
• /
• 2007

Correlation between occlusal contact pattern and TMD have been hypothesized and partially investigated but results are controversial and not conclusive. The purposes of this study were to compare right-to-left difference of occlusal contact pattern, through contact points, contact force and occlusal balance, in the patients with unilateral TMD and also to evaluate its change related with TMD treatment. 36 patients with unilateral TMD from Department of Oral Medicine in Dankook University Dental Hospital were selected in this study (M:F=7:29, mean age of $29.2{\pm}14.8$ years). A computerized T-Scan II system (Tekscan, INC., USA) was employed for occlusal analysis and the simultaneity and occlusal balance through the number of tooth contact and magnitude of contact force were determined before and after TMD treatment. The number of contact points and contact force was more on the unaffected side than the affected side before treatment (p=0.056 and p=0.060, respectively) while significant difference between both sides was not found after treatment. The number of contact points and contact force on the affected sides significantly increased after treatment (p=0.038 and p=0.052), but the unaffected sides exhibited no significant difference between before and after treatment. In addition, sides difference in relative contact force decreased from about 27% to about 12% after TMD treatment (p=0.001). According to the results of this study, it is likely that unilateral TMD impairs right-to-left occlusal balance and that conservative TMD treatment alleviates the imbalance, subsequently leading to more symmetrical occlusal condition with increased contact points and force.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.15 no.1
• /
• pp.167-184
• /
• 2020

This study analyzed the effects of information orientation and technology commercialization ability on technological performance of corporate workers. Information Orientation consisted of information technology capability, information management ability, information behavior and value, and technology commercialization capability consisted of productization capability, production capability, and marketing capability as sub-variables, and technology accumulation capacity was used as a coordinating variable. An empirical analysis was performed on 349 online and offline questionnaires collected from corporate employees. Analysis results using SPSS v22.0 and Process macro v3.4 First, information orientation and technical performance were found to have a significant effect.In addition, information orientation had a significant effect on technology commercialization capability. The magnitude of the influence on the productive capacity and the productive capacity in the variable of competency was in the order of information technology ability, information management ability, information behavior and value, but the influence on marketing capability was different from the previous results. Information management ability and information technology ability were in order. Second, the product commercialization capability, production capability, and marketing ability of technology commercialization ability had a significant effect on technology performance independently of information orientation. Third, the information technology ability and information management ability had a significant influence on the technical performance, but the indirect effect through the commercialization ability and marketing ability in information behavior and value was significant, the indirect effect of transit was not significant. Fourth, only the interaction terms of production capacity and technology accumulation capacity were significant among the sub-variables of technology commercialization capacity, and technology accumulation capacity, commercialization capacity, and marketing ability were not significant. Therefore, the relationship between productive capacity and technological performance can be interpreted as lower in firms with high technology accumulating ability than in lower firms, subsequent studies will require the introduction of other independent variables, models through the introduction of parameters and control variables.

• Asia pacific journal of information systems
• /
• v.18 no.2
• /
• pp.41-72
• /
• 2008

The purpose of this study is the investigation of the effects of user participation, network effect, social influence, and usefulness on stickiness and continued use on Internet communities. In this research, stickiness refers to repeat visit and visit duration to an Internet community. Continued use means the willingness to continue to use an Internet community in the future. Internet community-based companies can earn money through selling the digital contents such as game, music, and avatar, advertizing on internet site, or offering an affiliate marketing. For such money making, stickiness and continued use of Internet users is much more important than the number of Internet users. We tried to answer following three questions. Fist, what is the effects of user participation on stickiness and continued use on Internet communities? Second, by what is user participation formed? Third, are network effect, social influence, and usefulness that was significant at prior research about technology acceptance model(TAM) still significant on internet communities? In this study, user participation, network effect, social influence, and usefulness are independent variables, stickiness is mediating variable, and continued use is dependent variable. Among independent variables, we are focused on user participation. User participation means that Internet user participates in the development of Internet community site (called mini-hompy or blog in Korea). User participation was studied from 1970 to 1997 at the research area of information system. But since 1997 when Internet started to spread to the public, user participation has hardly been studied. Given the importance of user participation at the success of Internet-based companies, it is very meaningful to study the research topic of user participation. To test the proposed model, we used a data set generated from the survey. The survey instrument was designed on the basis of a comprehensive literature review and interviews of experts, and was refined through several rounds of pretests, revisions, and pilot tests. The respondents of survey were the undergraduates and the graduate students who mainly used Internet communities. Data analysis was conducted using 217 respondents(response rate, 97.7 percent). We used structural equation modeling(SEM) implemented in partial least square(PLS). We chose PLS for two reason. First, our model has formative constructs. PLS uses components-based algorithm and can estimated formative constructs. Second, PLS is more appropriate when the research model is in an early stage of development. A review of the literature suggests that empirical tests of user participation is still sparse. The test of model was executed in the order of three research questions. First user participation had the direct effects on stickiness(${\beta}$=0.150, p<0.01) and continued use (${\beta}$=0.119, p<0.05). And user participation, as a partial mediation model, had a indirect effect on continued use mediated through stickiness (${\beta}$=0.007, p<0.05). Second, optional participation and prosuming participation significantly formed user participation. Optional participation, with a path magnitude as high as 0.986 (p<0.001), is a key determinant for the strength of user participation. Third, Network effect (${\beta}$=0.236, p<0.001). social influence (${\beta}$=0.135, p<0.05), and usefulness (${\beta}$=0.343, p<0.001) had directly significant impacts on stickiness. But network effect and social influence, as a full mediation model, had both indirectly significant impacts on continued use mediated through stickiness (${\beta}$=0.11, p<0.001, and ${\beta}$=0.063, p<0.05, respectively). Compared with this result, usefulness, as a partial mediation model, had a direct impact on continued use and a indirect impact on continued use mediated through stickiness. This study has three contributions. First this is the first empirical study showing that user participation is the significant driver of continued use. The researchers of information system have hardly studies user participation since late 1990s. And the researchers of marketing have studied a few lately. Second, this study enhanced the understanding of user participation. Up to recently, user participation has been studied from the bipolar viewpoint of participation v.s non-participation. Also, even the study on participation has been studied from the point of limited optional participation. But, this study proved the existence of prosuming participation to design and produce products or services, besides optional participation. And this study empirically proved that optional participation and prosuming participation were the key determinant for user participation. Third, our study compliments traditional studies of TAM. According prior literature about of TAM, the constructs of network effect, social influence, and usefulness had effects on the technology adoption. This study proved that these constructs still are significant on Internet communities.

• Korean Journal of Biological Psychiatry
• /
• v.5 no.1
• /
• pp.95-101
• /
• 1998

The changes of electroencephalogram(EEG) in patients with dementia of Alzheimer's type are most commonly studied by analyzing power or magnitude in traditionally defined frequency bands. However because of the absence of an identified metric which quantifies the complex amount of information, there are many limitations in using such a linear method. According to the chaos theory, irregular signals of EEG can be also resulted from low dimensional deterministic chaos. Chaotic nonlinear dynamics in the EEG can be studied by calculating the largest Lyapunov exponent($L_1$). The authors have analyzed EEG epochs from three patients with dementia of Alzheimer's type and three matched control subjects. The largest $L_1$ is calculated from EEG epochs consisting of 16,384 data points per channel in 15 channels. The results showed that patients with dementia of Alzheimer's type had significantly lower $L_1$ than non-demented controls on 8 channels. Topographic analysis showed that the $L_1$ were significantly lower in patients with Alzheimer's disease on all the frontal, temporal, central, and occipital head regions. These results show that brains of patients with dementia of Alzheimer's type have a decreased chaotic quality of electrophysiological behavior. We conclude that the nonlinear analysis such as calculating the $L_1$ can be a promising tool for detecting relative changes in the complexity of brain dynamics.