• Journal of Magnetics
• /
• 제14권4호
• /
• pp.172-174
• /
• 2009

Nanolithography by atomic force microscope local oxidation was applied to the fabrication of planar-type Ni/Ni oxide/Ni junctions from 10 nm-thick Ni films. The junction characteristics were sensitive to the lithography conditions such as the bias voltage. Successful oxidation produced junctions of nonlinear current-voltage characteristics, implying the formation of oxide barriers. Magnetoresistance (MR) at low temperatures resembled that of spin valves.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.128-135
• /
• 1995

Atomic force microscopy/friction force microscopy (AFM/FFM) techniques are increasingly used for tribological studies of engineering surfaces at scales, ranging from atomic and molecular to microscales. These techniques have been used to study surface roughness, adhesion, friction, scratching/wear, indentation, detection of material transfer, and boundary lubrication and for nanofabrication/nanomachining purposes. Micro/nanotribological studies of single-crystal silicon, natural diamond, magnetic media (magnetic tapes and disks) and magnetic heads have been conducted. Commonly measured roughness parameters are found to be scale dependent, requiring the need of scale-independent fractal parameters to characterize surface roughness. Measurements of atomic-scale friction of a freshly-cleaved highly-oriented pyrolytic graphite exhibited the same periodicity as that of corresponding topography. However, the peaks in friction and those in corresponding topography were displaced relative to each other. Variations in atomic-scale friction and the observed displacement has been explained by the variations in interatomic forces in the normal and lateral directions. Local variation in microscale friction is found to correspond to the local slope suggesting that a ratchet mechanism is responsible for this variation. Directionality in the friction is observed on both micro- and macro scales which results from the surface preparation and anisotropy in surface roughness. Microscale friction is generally found to be smaller than the macrofriction as there is less ploughing contribution in microscale measurements. Microscale friction is load dependent and friction values increase with an increase in the normal load approaching to the macrofriction at contact stresses higher than the hardness of the softer material. Wear rate for single-crystal silicon is approximately constant for various loads and test durations. However, for magnetic disks with a multilayered thin-film structure, the wear of the diamond like carbon overcoat is catastrophic. Breakdown of thin films can be detected with AFM. Evolution of the wear has also been studied using AFM. Wear is found to be initiated at nono scratches. AFM has been modified to obtain load-displacement curves and for nanoindentation hardness measurements with depth of indentation as low as 1 mm. Scratching and indentation on nanoscales are the powerful ways to screen for adhesion and resistance to deformation of ultrathin fdms. Detection of material transfer on a nanoscale is possible with AFM. Boundary lubrication studies and measurement of lubricant-film thichness with a lateral resolution on a nanoscale have been conducted using AFM. Self-assembled monolyers and chemically-bonded lubricant films with a mobile fraction are superior in wear resistance. Finally, AFM has also shown to be useful for nanofabrication/nanomachining. Friction and wear on micro-and nanoscales have been found to be generally smaller compared to that at macroscales. Therefore, micro/nanotribological studies may help def'me the regimes for ultra-low friction and near zero wear.

• Journal of Magnetics
• /
• 제9권4호
• /
• pp.116-120
• /
• 2004

Hexagonal barium-ferrite ($BaFe_{12}O_{19}$, magnetoplumbite structure; BaM) film with perpendicularly c-axis orientation was successfully deposited on (100) silicon substrates with an MgO (111) underlayer by rf diode sputtering and in-situ heating at $920^{\circ}C$. The magnetic and structural properties of 0.27 ${\mu}m$ thick BaM films on MgO (111) underlayers were compared to films of the same thickness deposited onto single-crystal MgO (111) and c-plane ($000{\ell}$) sapphire ($Al_2O_3$) substrates by vibrating sample magnetometry (VSM), x-ray diffractometer (XRD), and atomic force microscopy (AFM). The thickness dependence of MgO (111) underlayers on silicon wafer was found to have a large effect on both magnetic and structural properties of the BaM film. The thickness of 15 nm MgO (111) underlayers produced BaM films with almost identical magnetic and structural properties as the single-crystal substrates; this can be explained by the lower surface roughness for thinner underlayer thicknesses. The magnetization saturation ($M_s$) and the ratio $H_{cII}/H_{c{\bot}}$ for the BaM film with a 15 nm MgO (111) underlayer is 217 emu/cc and 0.24, respectively. This is similar to the results for the BaM films deposited on the single-crystal MgO (111) and sapphire substrates of 197 emu/cc and 0.10, 200 emu/cc and 0.12, respectively. Therefore, the proposed MgO (111) underlayer can be used in many applications to promote c-axis orientation without the cost of expensive substrates.

• Tribology and Lubricants
• /
• 제31권2호
• /
• pp.62-68
• /
• 2015

A magnetorheological (MR) fluid is a smart material whose rheological behavior can be controlled by varying the parameters of the applied magnetic field. Because the damping force and shear force of an MR fluid can be controlled using a magnetic field, it is widely employed in many industrial applications, such as in vehicle vibration control, powertrains, high-precision grinding processes, valves, and seals. However, the characteristics of friction caused by iron particles inside the MR fluid need to be understood and improved so that it can be used in practical applications. Surface process technologies such as polytetrafluoroethylene (PTFE) coatings and diamond-like carbon (DLC) coatings are widely used to improve the surface friction properties. This study examines the friction characteristics of an MR fluid with different surface process technologies such as PTFE coatings and DLC coatings, by using a reciprocating friction tester. The coefficients of friction are in the following descending order: MR fluid without any coating, MR fluid with a DLC coating, and MR fluid with a PTFE coating. Scanning electron microscopy is used to observe the worn surfaces before and after the experiment. In addition, energy dispersive X-ray spectroscopy is used to analyze the chemical composition of the worn surface. Through a comparison of the results, the friction characteristics of the MR fluid based on the different coating technologies are analyzed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.375-375
• /
• 2009

For many large-scale applications of high-temperature superconducting materials, large critical current density($J_c$) in high applied magnetic fields are required. A number of methods have been reported to introduce artificial pinning centers(APCs) in $YBa_2Cu_3O_{7-\delta}$(YBCO) films for enhancement of their $J_c$. We report measurements of critical current in $YBa_2Cu_3O_{7-\delta}$ films deposited by PLD on $SrTiO_3$ substrates decorated with Au nanoparticles. Au nanoparticles were synthesized on STO substrates with self assembled monolayer. Microstructural analysis of the obtained YBCO films was performed by using cross-section transmission electron microscopy(TEM). Phase and textural analysis was done using X-ray diffraction. The surface morphology and surface roughness(Ra) of the layers was measured by atomic force microscopy(AFM).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.251-251
• /
• 2012

A lot of studies are undergoing on the magneto-optical (MO) properties of patterned magnetic systems for the reason that they have potential application to information technology such as ultrahigh-speed computing. Moreover, they can be considered as the future candidates for high-density MO storage devices. Not only the technical aspects, but there have been also tremendous interests in studying their properties related to the fundamental physics. The MO Kerr-rotation effects (both in reflected and the diffracted modes) and the magnetic force microscopy (MFM) are very useful techniques to investigate the micromagnetic properties of such periodic structures. Hence, in this study, we report on the MO properties of bilayered Cobalt (Co)/ nickel (Ni) micro-patterned anti-dot arrays. Such a ferromagnetic structure was made by sequentially depositing co (40 nm)/Ni (5 nm) bilayer on a Si substrate. The anti-dot patterning with hole diameter of $1{\mu}m$ was done only on the upper Co layer using photolithography technique, while the Ni underlayer was kept uniform. The longitudinal Kerr rotation (LKR) of the zeroth- and the first-order diffracted beams were measured at an incidence of $30^{\circ}$ by using a photoelastic modulator method. The external magnetic field was applied perpendicularly to the reflected and the diffracted beams using an electromagnet capable of a maximum field of ${\pm}5$ kOe. Significantly, it was observed that the LKR of the first-order diffracted beam is nearly 4 times larger than that of the zeroth-order beam. The simulated results for the hysteresis loops matched qualitatively well with the experimentally obtained ones. In conjunction with the LKR, we also investigated the magnetic-domain structure by using a MFM system, which were analyzed to elucidate the origin of the enhanced MO rotation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.218.2-218.2
• /
• 2014

그래핀은 높은 전기 전도도와 열전도도, 기계적 강도를 가지고 있고 동시에 높은 전자이동도($200,000cm^2{\cdot}V{\cdot}^1{\cdot}s{\cdot}^1$) 특성을 갖는 물질로써 차세대 소재로 각광받고 있다. 하지만 그래핀을 소자에 응용하기 위해서는 전사공정과 lithography 공정 과정에서 발생되는 PMMA(Poly methyl methacrylate) residue를 완벽하게 제거해야 하는 문제점이 있다. 특히, lithography 공정 중 완벽하게 PMMA residue 가 제거되지 않고 잔류해 있을 경우에 소자의 life time, performance에 악영향을 준다는 보고가 있다. 이와같은 문제를 해결하기 위해 화학적 cleaning, 열처리를 통한 cleaning, 전류 인가에 의한 cleaning과 같은 방법들을 이용하여 그래핀의 PMMA residue를 제거하는 공정들이 보고되고 있지만, 화학적 cleaning 방법의 경우 chloroform 이라는 독성물질 사용으로 인해 산업적으로 응용이 어렵고, 열처리 방법은 전극 등의 금속이 $200^{\circ}C$ 이상의 높은 온도에서 장시간 노출될 경우 쉽게 손상을 입으며, 전류 인가에 의한 cleaning 방법은 국부적으로만 효과를 볼 수 있기 때문에 lithography 공정 후 PMMA residue를 효과적으로 제거하기에는 한계를 보이고 있다. 본 연구에서는 Ar을 이용하는 Ion beam 시스템을 통해 beam energy를 제어함으로써 PMMA residue를 효과적으로 제거하는 연구를 진행하였다. 최적화된 플라즈마 발생 조건을 찾기 위해 QMS(Quadrupole Mass Spectrometer)를 이용하여 입사하는 ion energy와 flux 양을 컨트롤 하였고, 250 W에서 최적화된 ion energy distribution 영역이 존재한다는 것을 확인할 수 있었다. 또한, 25 Gauss 정도의 electro-magnetic field를 이용하여 Ar의 ion energy를 10 eV 이하로 낮추어 damage를 최소화함으로써 효과적으로 그래핀을 cleaning 할 수 있었다. Cleaning과정에서 ion bombardment에 의해 발생한 damage는 $250^{\circ}C$에서 6시간 동안 annealing 공정을 거치면서 회복되는 것을 Raman spectroscopy의 D peak ($1335cm{\cdot}^1$) / G peak ($1572cm{\cdot}^1$) ratio 로 확인할 수 있었고, PMMA residue의 cleaning 여부는 G peak ($1580cm{\cdot}^1$)의 blue shift와 2D peak ($2670cm{\cdot}^1$)의 red shift를 통해 확인하였다. 그리고 AFM (Atomic Force Microscopy)을 이용하여 cleaning 공정과정에서 RMS roughness가 4.99 nm에서 2.01 nm로 감소하는 것을 관찰하였다. 마지막으로, PMMA residue의 cleaning 정도를 정량적으로 분석하기 위해 XPS (X-ray Photoelectron Spectroscopy)를 이용하여 sp2 C-C bonding이 74.96%에서 87.66%로 증가함을 확인을 할 수 있었다.

• KSTLE International Journal
• /
• 제1권1호
• /
• pp.12-20
• /
• 2000

Nano-wear and friction of carbon overcoated laser-textured and mechanically-textured computer hard disk were characterised after contact start/stop (CSS) wear test. Various analytical and mechanical testing techniques were employed to study the changes in topography, roughness, chemical elements, mechanical properties and friction characteristics of the coating arising from the contact start/stop wear test These techniques include: the atomic force microscopy (AFM), the continuous nano-indentation test, the nano-scratch test, the time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and the auger electron spectroscopy (AES). It was shown that the surface roughness of the laser-textured (LT) bump and mechanically textured (MT) Bone was reduced approximately am and 7nm, respectively, after the CSS wear test. The elastic modulus and hardness values increased after the CSS test, indicating straining hardening of the top coating layer, A critical load was also identified fer adhesion failure between the magnetic layer and the Ni-P layer, The TOF-SIMS analysis also revealed some reduction in the intensity of C and $C_2$$F_59$, confirming the wear of lubricant elements on the coating surface.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.263-270
• /
• 1998

상용화된 박막 코팅 자기 저장 디스크의 기계역학 및 윤활적 물성치를 도출하기 위하여 Nano-Indentation 과 Nano-Scratch 실험이 수행되었다. 자기 디스크는 원주방향으로 일정한의 분석을 위하여 AFM(Atomic Force Microscopy)이 사용되었다. 텍스처 방향에 따른 표면조도의 변화는 가우스 확률 분포(Gaussian probability distribution)와 Weibull누적 확률 이론(Weibull cumulative probability theory)에 의하여 분석되었다. 표면 조도와 마찰계수는 텍스처의 스캐닝(scanning) 방향에 의존한다는 것이 확인 되었다.

• Molecules and Cells
• /
• 제45권1호
• /
• pp.33-40
• /
• 2022

The various DNA-protein interactions associated with the expression of genetic information involve double-stranded DNA (dsDNA) bending. Due to the importance of the formation of the dsDNA bending structure, dsDNA bending properties have long been investigated in the biophysics field. Conventionally, DNA bendability is characterized by innate averaging data from bulk experiments. The advent of single-molecule methods, such as atomic force microscopy, optical and magnetic tweezers, tethered particle motion, and single-molecule fluorescence resonance energy transfer measurement, has provided valuable tools to investigate not only the static structures but also the dynamic properties of bent dsDNA. Here, we reviewed the single-molecule methods that have been used for investigating dsDNA bendability and new findings related to dsDNA bending. Single-molecule approaches are promising tools for revealing the unknown properties of dsDNA related to its bending, particularly in cells.